Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT AIRBAG SENSOR › 2018.10–2019.02
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0374453 FRONT AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT AIRBAG SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front airbag sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system
·

for A25A-FKS:

(Click here)

·

for M20A-FKS:

(Click here)


Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 4.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 89174A 6.REMOVE FRONT AIRBAG SENSOR LH

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·
B392779

If this procedure is performed without disconnecting the negative (-) auxiliary battery terminal of the battery, the airbag may deploy even if an impact is applied only to the front airbag sensor. Therefore, make sure that the negative (-) auxiliary battery terminal of the battery is disconnected before performing this procedure.




c.

Disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.

Push down the housing lock and slide the CPA. (At this time, the connector cannot be disconnected yet.)

B340847C06
4.26,1.01 4.625,0.594 4.625,0.594 4.979,0.594 true 3.354,1.698 3.594,1.698 3.594,1.698 3.729,1.229 true 3.021,0.438 3.333,0.438 3.333,0.438 3.646,0.76 true 5.031,0.49 5.344,0.646 0.313,0.156 10 false *a 3.177,1.594 3.49,1.75 0.313,0.156 10 false *b 2.844,0.323 3.146,0.531 0.302,0.208 10 false *c 5.469,2.104 5.771,2.313 0.302,0.208 10 false *d
*a Housing Lock *b CPA
*c CPA Upper Part *d Connector Lock is Released



ii.

Push the housing lock again and disconnect the connector.

NOTICE:

Do not push down the upper part of the CPA shown in the illustration when disconnecting the airbag connector.



iii.

After disconnecting the connector, check that the position of the housing lock is correct as shown in the illustration.

H043304C21
3.208,1.271 3.208,1.354 3.208,1.354 3.5,1.354 false 3.115,2.615 3.115,2.708 3.115,2.708 3.531,2.708 false 5.938,1.26 6.031,1.26 6.031,1.26 6.031,0.938 false 5.938,2.583 6.031,2.583 6.031,2.583 6.031,2.26 false 5.469,1.313 5.469,1.156 5.469,1.156 5.646,0.948 true 4.781,2.125 5.031,2.125 5.031,2.125 5.417,2.125 true 3.563,1.271 3.74,1.417 0.177,0.146 10 false *a 3.583,2.625 3.76,2.792 0.177,0.167 10 false *a 5.781,1.188 5.958,1.333 0.177,0.146 10 false *a 5.781,2.51 5.958,2.656 0.177,0.146 10 false *a 0.792,0.344 1.625,1.125 0.833,0.781 10 true *c 0.792,1.833 1.552,2.458 0.76,0.625 10 true *d 3.979,0.344 4.813,1.146 0.833,0.802 10 true *c 3.979,1.833 4.74,2.458 0.76,0.625 10 true *d 5.417,1.333 5.594,1.479 0.177,0.146 10 false *b 4.604,2.042 4.781,2.188 0.177,0.146 10 false *b
*a CPA *b Housing
*c Correct *d Incorrect




d.
B523167C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the bolt.

NOTICE:
·

Loosen the bolt while holding the front airbag sensor LH because the front airbag sensor LH claw is easily damaged.

·

If the front airbag sensor LH has been dropped, replace it with a new one.




e.

Detach the claw to remove the front airbag sensor LH.