Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR (for Front Door) › 2018.10–2019.02
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0374454 SIDE AIRBAG SENSOR(for Front Door) A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR(for Front Door)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 8983AA 1.INSTALL SIDE AIRBAG PRESSURE SENSOR LH

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·
B392779

If this procedure is performed without disconnecting the negative (-) auxiliary battery terminal, the airbag may deploy even if an impact is applied only to the side airbag pressure sensor LH. Therefore, make sure that the negative (-) auxiliary battery terminal is disconnected before performing this procedure.




c.

Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


i.

Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

H043304C29
3.208,1.271 3.208,1.354 3.208,1.354 3.5,1.354 false 3.115,2.615 3.115,2.708 3.115,2.708 3.531,2.708 false 5.938,1.26 6.031,1.26 6.031,1.26 6.031,0.938 false 5.938,2.583 6.031,2.583 6.031,2.583 6.031,2.26 false 5.469,1.313 5.469,1.156 5.469,1.156 5.646,0.948 true 4.781,2.125 5.031,2.125 5.031,2.125 5.417,2.125 true 3.563,1.271 3.74,1.417 0.177,0.146 10 false *c 3.583,2.625 3.76,2.792 0.177,0.167 10 false *c 5.781,1.188 5.958,1.333 0.177,0.146 10 false *c 5.781,2.51 5.958,2.656 0.177,0.146 10 false *c 0.792,0.344 1.625,1.125 0.833,0.781 10 true *a 0.792,1.833 1.552,2.458 0.76,0.625 10 true *b 3.979,0.344 4.813,1.146 0.833,0.802 10 true *a 3.979,1.833 4.74,2.458 0.76,0.625 10 true *b 5.417,1.333 5.594,1.479 0.177,0.146 10 false *d 4.604,2.042 4.781,2.188 0.177,0.146 10 false *d
*a Correct *b Incorrect
*c CPA *d Housing



ii.

While holding the CPA be sure to engage the connectors until they are locked and check that the CPA is in its original position (when locking, make sure that a click sound can be heard).

NOTICE:

Do not push down the upper part of the CPA shown in the illustration when connecting the airbag connector.


B312074C31
2.208,0.802 2.563,0.51 true 2.406,1 2.75,0.708 true 2.469,1.396 2.469,1.719 false 2.802,0.646 3.01,0.854 0.208,0.208 10 false *b 2.396,1.729 2.635,1.948 0.24,0.219 10 false *c 5.948,2.208 6.219,2.458 0.271,0.25 10 false *d 2.615,0.417 2.865,0.646 0.25,0.229 10 false *a
*a CPA Upper Part *b Housing Lock
*c CPA *d Connection is Completed




d.
B523171

Attach the claw to hold the side airbag pressure sensor LH in place.

NOTICE:
·

If the side airbag pressure sensor LH has been dropped, replace it with a new one.

·

When installing the side airbag pressure sensor LH, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

·
B520059

Waterproof rubber seals that are damaged on the side airbag pressure sensor LH (blue area in illustration) cannot be reused.




e.

Install the nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


f.

Check that there is no looseness in the installation parts of the side airbag pressure sensor LH.


Hide 67832 2.INSTALL FRONT DOOR SERVICE HOLE COVER LH

Hide 67602 3.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 4.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

Hide 5.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

Hide 74642A 6.INSTALL FRONT DOOR ASSIST GRIP COVER LH

Hide 69278B 7.INSTALL FRONT DOOR INSIDE HANDLE BEZEL LH

Hide 8.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 65351A 9.INSTALL BATTERY HOLE COVER (for HV Model)

Hide 58416K 10.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 58410B 11.INSTALL DECK BOARD ASSEMBLY (for HV Model)

Hide 14.PERFORM SYSTEM INITIALIZATION AND CALIBRATION