Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR (for Center Pillar) › 2018.10–2019.02
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0374455 SIDE AIRBAG SENSOR(for Center Pillar) A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR(for Center Pillar)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89831E 1.INSTALL FLOOR SIDE AIRBAG SENSOR LH

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·
B392779

If this procedure is performed without disconnecting the negative (-) auxiliary battery terminal, the airbag may deploy even if an impact is applied only to the floor side airbag sensor LH. Therefore, make sure that the negative (-) auxiliary battery terminal is disconnected before performing this procedure.




c.
B523469C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and hold the floor side airbag sensor LH in place.


d.

Install the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the floor side airbag sensor LH has been dropped, replace it with a new one.

·

When installing the floor side airbag sensor LH, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

·

Tighten the bolt while holding the floor side airbag sensor LH because the floor side airbag sensor LH claw is easily damaged.




e.

Check that there is no looseness in the installation parts of the floor side airbag sensor LH.


f.

Connect the airbag connector.

i.

Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

H043304C29
3.208,1.271 3.208,1.354 3.208,1.354 3.5,1.354 false 3.115,2.615 3.115,2.708 3.115,2.708 3.531,2.708 false 5.938,1.26 6.031,1.26 6.031,1.26 6.031,0.938 false 5.938,2.583 6.031,2.583 6.031,2.583 6.031,2.26 false 5.469,1.313 5.469,1.156 5.469,1.156 5.646,0.948 true 4.781,2.125 5.031,2.125 5.031,2.125 5.417,2.125 true 3.563,1.271 3.74,1.417 0.177,0.146 10 false *c 3.583,2.625 3.76,2.792 0.177,0.167 10 false *c 5.781,1.188 5.958,1.333 0.177,0.146 10 false *c 5.781,2.51 5.958,2.656 0.177,0.146 10 false *c 0.792,0.344 1.625,1.125 0.833,0.781 10 true *a 0.792,1.833 1.552,2.458 0.76,0.625 10 true *b 3.979,0.344 4.813,1.146 0.833,0.802 10 true *a 3.979,1.833 4.74,2.458 0.76,0.625 10 true *b 5.417,1.333 5.594,1.479 0.177,0.146 10 false *d 4.604,2.042 4.781,2.188 0.177,0.146 10 false *d
*a Correct *b Incorrect
*c CPA *d Housing



ii.

While holding the CPA, be sure to engage the connectors until they are locked and check that the CPA is in its original position (when locking, make sure that a click sound can be heard).

NOTICE:

Do not push down the upper part of the CPA shown in the illustration when connecting the airbag connector.


B312074C31
2.208,0.802 2.563,0.51 true 2.406,1 2.75,0.708 true 2.469,1.396 2.469,1.719 false 2.802,0.646 3.01,0.854 0.208,0.208 10 false *b 2.396,1.729 2.635,1.948 0.24,0.219 10 false *c 5.948,2.208 6.219,2.458 0.271,0.25 10 false *d 2.615,0.417 2.865,0.646 0.25,0.229 10 false *a
*a CPA Upper Part *b Housing Lock
*c CPA *d Connection is Completed




Hide 62414A 2.INSTALL LOWER CENTER PILLAR GARNISH LH

a.

Install the lower center pillar garnish LH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


b.

Return the front door opening trim weatherstrip LH to its original position.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR OPENING TRIM WEATHERSTRIP>INSTALLATION


c.

Return the rear door opening trim weatherstrip LH to its original position.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP>INSTALLATION


Hide 73233 3.INSTALL LAP BELT OUTER ANCHOR COVER

Hide 67918E 4.INSTALL REAR DOOR SCUFF PLATE LH

Hide 72693 5.INSTALL REAR SEAT CUSHION LOCK HOOK (for Gasoline Model)

Hide 6.INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY (for Gasoline Model)

Hide 67914B 7.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 8.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 65351A 9.INSTALL BATTERY HOLE COVER (for HV Model)

Hide 58416K 10.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 58410B 11.INSTALL DECK BOARD ASSEMBLY (for HV Model)