Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR AIRBAG SENSOR › 2018.10–2019.02
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0374456 REAR AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  REAR AIRBAG SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89860C 1.INSTALL NO. 2 SIDE AIRBAG SENSOR ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·
B392779

If this procedure is performed without disconnecting the negative (-) auxiliary battery terminal of the battery, the airbag may deploy even if an impact is applied only to the No. 2 side airbag sensor assembly. Therefore, make sure that the negative (-) auxiliary battery terminal of the battery is disconnected before performing this procedure.




c.
B523174C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and hold the No. 2 side airbag sensor assembly in place.


d.

Install the No. 2 side airbag sensor assembly with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the No. 2 side airbag sensor assembly has been dropped, replace it with a new one.

·

When installing the No. 2 side airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

·

Tighten the bolt while holding the No. 2 side airbag sensor assembly because the No. 2 side airbag sensor assembly claw is easily damaged.




e.

Check that there is no looseness in the installation parts of the No. 2 side airbag sensor assembly.


f.

Connect the airbag connector.

i.

Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

B319865C14
2.719,1.406 3.26,1.406 false 5.958,1.417 6.5,1.417 false 0.531,1.771 0.802,1.771 false 3.333,1.323 3.646,1.479 0.313,0.156 10 false *c 6.552,1.333 6.865,1.49 0.313,0.156 10 false *c 1.75,1.042 2.135,1.24 0.385,0.198 10 true *a 5,1.021 5.292,1.188 0.292,0.167 10 true *b 0.354,1.698 0.667,1.854 0.313,0.156 10 false *d 0.042,0.052 5.885,0.583 5.844,0.531 6 true . 1.313,0.49 7.094,0.76 5.781,0.271 6 true . 1.323,0.604 2.656,0.99 1.333,0.385 6 true . 4.615,0.552 5.948,0.938 1.333,0.385 6 true .
*a Correct *b Incorrect
*c CPA *d Housing



ii.

While holding the CPA, be sure to engage the connectors until they are locked and check that the CPA is in its original position (when locking, make sure that a click sound can be heard).

NOTICE:

Do not push down the upper part of the CPA shown in the illustration when connecting the airbag connector.


B403898C01
1.594,1.958 1.594,1.208 false 3.469,1.167 3.125,0.583 true 5.448,0.906 5.76,1.063 0.313,0.156 10 false *c 1.542,2.01 1.854,2.167 0.313,0.156 10 false *a 2.938,0.479 3.25,0.635 0.313,0.156 10 false *b
*a CPA *b CPA Upper Part
*c Connection is Completed - -
V113147

Connect in this Direction - -




Hide 62552F 2.INSTALL REAR SEAT SIDE GARNISH LH

a.

Install the rear seat No. 3 side garnish LH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


b.

Return the rear door opening trim weatherstrip LH to its original position.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP>INSTALLATION


Hide 67918E 3.INSTALL REAR DOOR SCUFF PLATE LH (for Gasoline Model)

Hide 4.INSTALL REAR SEAT ASSEMBLY

Hide 5.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 65351A 6.INSTALL BATTERY HOLE COVER (for HV Model)

Hide 58416K 7.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 58410B 8.INSTALL DECK BOARD ASSEMBLY (for HV Model)

Hide 11.PERFORM SYSTEM INITIALIZATION AND CALIBRATION