Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM3620E _59 Vehicle Exterior _077130 LIGHTING (EXT) _0375584 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B2439  Headlight LH Circuit  B243A  Headlight RH Circuit  


DESCRIPTION

The headlight ECU sub-assembly LH and headlight ECU sub-assembly RH internally boost the power supply voltage to ensure a constant supplied current for the Lo/Hi beam LED of their respective headlight.

By monitoring the LED power supply voltage, abnormal current and malfunctions can be detected.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
B2439 Headlight LH Circuit
Detection condition:

All of the following conditions are met:

-

Ignition switch ON

-

Low beam headlights on



Malfunction status:
·

Headlight LED unit assembly malfunction

·

Open/short in Lo/Hi beam circuit


Malfunction duration:

10 seconds or more


·

Headlight LED unit assembly LH

·

Headlight unit assembly LH

·

Headlight ECU sub-assembly LH


Headlight ECU sub-assembly LH -
B243A Headlight RH Circuit
Detection condition:

All of the following conditions are met:

-

Ignition switch ON

-

Low beam headlights on



Malfunction status:
·

Headlight LED unit assembly malfunction

·

Open/short in Lo/Hi beam circuit


Malfunction duration:

10 seconds or more


·

Headlight LED unit assembly RH

·

Headlight unit assembly RH

·

Headlight ECU sub-assembly RH


Headlight ECU sub-assembly RH -

WIRING DIAGRAM

for Triple Beam Headlight


E406766E01
0.156,4.26 4.135,4.458 3.979,0.198 10 false Headlight ECU Sub-assembly 3.146,3.854 7.125,4.052 3.979,0.198 10 false Headlight Unit Assembly 0.927,0.875 4.906,1.073 3.979,0.198 10 false LOLED2 0.927,2.156 2.167,2.396 1.24,0.24 10 false LOLED0 1.542,0.802 2.781,1.042 1.24,0.24 10 false 4 1.531,2.063 2.771,2.302 1.24,0.24 10 false 3 4.458,0.792 5.698,1.031 1.24,0.24 10 false 1 4.469,1.458 5.708,1.698 1.24,0.24 10 false 4 4.458,1.771 5.698,2.01 1.24,0.24 10 false 3 4.458,2.073 5.698,2.313 1.24,0.24 10 false 6 5.542,2.031 6.781,2.271 1.24,0.24 10 false Hi Beam 5.542,1.208 6.781,1.448 1.24,0.24 10 false Lo Beam 2.104,3.271 4.365,3.479 2.26,0.208 10 false Electrical Light Source Control Gear 4.563,3.271 6.521,3.479 1.958,0.208 10 false Headlight LED Unit Assembly 0.177,4.104 4.156,4.302 3.979,0.198 10 false B 2.104,3.115 4.063,3.323 1.958,0.208 10 false C 4.563,3.104 6.521,3.313 1.958,0.208 10 false D 3.688,0.781 4.927,1.021 1.24,0.24 10 false 7 3.688,1.76 4.927,2 1.24,0.24 10 false 1 3.698,1.469 4.938,1.708 1.24,0.24 10 false 2 3.698,2.073 4.938,2.313 1.24,0.24 10 false 5 2.625,2.063 3.865,2.302 1.24,0.24 10 false 6 2.625,0.792 3.865,1.031 1.24,0.24 10 false 8 1.083,2.698 2.323,2.938 1.24,0.24 10 false FANP 1.51,2.594 2.75,2.833 1.24,0.24 10 false 15 2.635,2.604 3.875,2.844 1.24,0.24 10 false 3


for Single Beam Headlight


E333074E45
0.229,3.271 2.271,3.583 2.042,0.313 10 false Headlight ECU Sub-assembly 3.094,2.938 4.74,3.375 1.646,0.438 10 false Headlight Unit Assembly 4.594,2.448 6.76,2.688 2.167,0.24 10 false Headlight LED Unit Assembly 5.49,1.469 6.573,1.76 1.083,0.292 10 false Lo/Hi Beam 1.552,1.219 1.771,1.417 0.219,0.198 10 false 4 1.552,1.615 1.771,1.833 0.219,0.219 10 false 3 4.448,1.219 4.604,1.417 0.156,0.198 10 false 1 4.448,1.625 4.604,1.823 0.156,0.198 10 false 6 4.594,2.271 4.75,2.469 0.156,0.198 10 false C 0.219,3.125 0.375,3.323 0.156,0.198 10 false B 0.927,1.313 1.615,1.542 0.688,0.229 10 false LOLED2 0.927,1.719 1.615,1.948 0.688,0.229 10 false LOLED0


CAUTION / NOTICE / HINT

NOTICE:

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>INITIALIZATION


PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.


e.

Clear the DTCs.

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361
Body Electrical > HL AutoLeveling (Sub) > Clear DTCs
50002 414

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Operate the light control switch to turn on the low beam headlights and wait 10 seconds or more.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.


f.

Check for DTCs.

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
Body Electrical > HL AutoLeveling (Sub) > Trouble Codes
50001 414
OK:

DTC B2439 and B243A are not output.



Result:
Result Proceed to
OK A
NG (DTC B2439 is output) B
NG (DTC B243A is output) C



A

B

3.CHECK HEADLIGHT UNIT ASSEMBLY LH

C

10.CHECK HEADLIGHT UNIT ASSEMBLY RH
3.CHECK HEADLIGHT UNIT ASSEMBLY LH
a.

Interchange the headlight unit assembly LH with RH and connect the connectors.

for Triple Beam Headlight:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Triple Beam Headlight)>DISASSEMBLY

for Single Beam Headlight:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for Single Beam Headlight)>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.


e.

Clear the DTCs.

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361
Body Electrical > HL AutoLeveling (Sub) > Clear DTCs
50002 414

Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Operate the light control switch to turn on the low beam headlights and wait 10 seconds or more.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.


f.

Check for DTCs.

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
Body Electrical > HL AutoLeveling (Sub) > Trouble Codes
50001 414

Result:
Result Proceed to
DTC B2439 is output A
DTC B243A is output B



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

B

6.CONFIRM MODEL
6.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for Triple Beam Headlight A
for Single Beam Headlight B



A

7.INSPECT HEADLIGHT UNIT ASSEMBLY LH

B

9.INSPECT HEADLIGHT UNIT ASSEMBLY LH
7.INSPECT HEADLIGHT UNIT ASSEMBLY LH
E411292C01
1.302,0.51 1.677,0.76 0.375,0.25 6.125,0.427 6.5,0.677 0.375,0.25 3.938,0.5 4.313,0.75 0.375,0.25 1.219,1.99 1.292,1.469 true 0.625,2.01 1.167,1.458 true 1.854,1.99 1.427,1.635 true 0.156,0.698 0.469,0.896 0.313,0.198 10 false *a 5.479,0.75 5.792,0.948 0.313,0.198 10 false *c 1.438,0.552 1.75,0.75 0.313,0.198 10 false B 6.281,0.458 6.594,0.656 0.313,0.198 10 false D 1.031,2.052 1.677,2.292 0.646,0.24 10 false LOLED2 0.323,2.052 0.969,2.292 0.646,0.24 10 false LOLED0 4.083,0.542 4.396,0.74 0.313,0.198 10 false C 2.802,0.708 3.115,0.906 0.313,0.198 10 false *b 1.781,2.052 2.427,2.292 0.646,0.24 10 false FANP
*a Component without harness connected
(to Headlight ECU Sub-assembly LH)
*b Component without harness connected
(to Electrical Light Source Control Gear LH)
*c Component without harness connected
(to Headlight LED Unit Assembly LH)
- -




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Wiring Color Condition Specified Condition
B-4 (LOLED2) - C-8 V Always Below 1 Ω
B-3 (LOLED0) - C-6 O Always Below 1 Ω
B-15 (FANP) - C-3 G Always Below 1 Ω
C-7 - D-1 L Always Below 1 Ω
C-2 - D-4 B Always Below 1 Ω
C-1 - D-3 Y Always Below 1 Ω
C-5 - D-6 BR Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HEADLIGHT LED UNIT ASSEMBLY LH

NG

8.CHECK HEADLIGHT LED UNIT ASSEMBLY LH
a.

Temporarily replace the headlight LED unit assembly LH with a new one or normally functioning one.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Triple Beam Headlight)>DISASSEMBLY


b.

Check the operation of the Lo/Hi beam light.

·

Turn the ignition switch to ON.

·

Turn the light control switch to the AUTO or HEAD position.


OK:

Lo/Hi beam light operates normally.



Result:
Proceed to
OK
NG



OK

END (HEADLIGHT LED UNIT ASSEMBLY LH IS DEFECTIVE)

NG

9.INSPECT HEADLIGHT UNIT ASSEMBLY LH
E411289C01
1.708,0.354 2.073,0.656 0.365,0.302 4.844,0.417 5.208,0.719 0.365,0.302 1.198,2.125 1.604,1.448 true 1.844,2.156 1.719,1.458 true 0.615,0.438 0.927,0.635 0.313,0.198 10 false *a 4.115,0.469 4.427,0.667 0.313,0.198 10 false *b 1.854,0.417 2.167,0.615 0.313,0.198 10 false B 4.969,0.51 5.281,0.708 0.313,0.198 10 false C 1.031,2.167 1.708,2.385 0.677,0.219 10 false LOLED0 1.76,2.188 2.438,2.406 0.677,0.219 10 false LOLED2
*a Component without harness connected
(to Headlight ECU Sub-assembly LH)
*b Component without harness connected
(to Headlight LED Unit Assembly LH)




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Wiring Color Condition Specified Condition
B-4 (LOLED2) - C-1 BR Always Below 1 Ω
B-3 (LOLED0) - C-6 W Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

10.CHECK HEADLIGHT UNIT ASSEMBLY RH
a.

Interchange the headlight unit assembly RH with LH and connect the connectors.

for Triple Beam Headlight:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Triple Beam Headlight)>DISASSEMBLY

for Single Beam Headlight:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for Single Beam Headlight)>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

11.CLEAR DTC
11.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.


e.

Clear the DTCs.

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361
Body Electrical > HL AutoLeveling (Sub) > Clear DTCs
50002 414

Result:
Proceed to
NEXT



NEXT

12.CHECK FOR DTC
12.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Operate the light control switch to turn on the low beam headlights and wait 10 seconds or more.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.


f.

Check for DTCs.

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
Body Electrical > HL AutoLeveling (Sub) > Trouble Codes
50001 414

Result:
Result Proceed to
DTC B243A is output A
DTC B2439 is output B



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

B

13.CONFIRM MODEL
13.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for Triple Beam Headlight A
for Single Beam Headlight B



A

14.INSPECT HEADLIGHT UNIT ASSEMBLY RH

B

16.INSPECT HEADLIGHT UNIT ASSEMBLY RH
14.INSPECT HEADLIGHT UNIT ASSEMBLY RH
E411292C01
1.302,0.51 1.677,0.76 0.375,0.25 6.125,0.427 6.5,0.677 0.375,0.25 3.938,0.5 4.313,0.75 0.375,0.25 1.219,1.99 1.292,1.469 true 0.625,2.01 1.167,1.458 true 1.854,1.99 1.427,1.635 true 0.156,0.698 0.469,0.896 0.313,0.198 10 false *a 5.479,0.75 5.792,0.948 0.313,0.198 10 false *c 1.438,0.552 1.75,0.75 0.313,0.198 10 false B 6.281,0.458 6.594,0.656 0.313,0.198 10 false D 1.031,2.052 1.677,2.292 0.646,0.24 10 false LOLED2 0.323,2.052 0.969,2.292 0.646,0.24 10 false LOLED0 4.083,0.542 4.396,0.74 0.313,0.198 10 false C 2.802,0.708 3.115,0.906 0.313,0.198 10 false *b 1.781,2.052 2.427,2.292 0.646,0.24 10 false FANP
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to Electrical Light Source Control Gear RH)
*c Component without harness connected
(to Headlight LED Unit Assembly RH)
- -




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Wiring Color Condition Specified Condition
B-4 (LOLED2) - C-8 V Always Below 1 Ω
B-3 (LOLED0) - C-6 O Always Below 1 Ω
B-15 (FANP) - C-3 G Always Below 1 Ω
C-7 - D-1 L Always Below 1 Ω
C-2 - D-4 B Always Below 1 Ω
C-1 - D-3 Y Always Below 1 Ω
C-5 - D-6 BR Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

15.CHECK HEADLIGHT LED UNIT ASSEMBLY RH

NG

15.CHECK HEADLIGHT LED UNIT ASSEMBLY RH
a.

Temporarily replace the headlight LED unit assembly RH with a new one or normally functioning one.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Triple Beam Headlight)>DISASSEMBLY


b.

Check the operation of the Lo/Hi beam light.

·

Turn the ignition switch to ON.

·

Turn the light control switch to the AUTO or HEAD position.


OK:

Lo/Hi beam light operates normally.



Result:
Proceed to
OK
NG



OK

END (HEADLIGHT LED UNIT ASSEMBLY RH IS DEFECTIVE)

NG

16.INSPECT HEADLIGHT UNIT ASSEMBLY RH
E411289C01
1.708,0.354 2.073,0.656 0.365,0.302 4.844,0.417 5.208,0.719 0.365,0.302 1.198,2.125 1.604,1.448 true 1.844,2.156 1.719,1.458 true 0.615,0.438 0.927,0.635 0.313,0.198 10 false *a 4.115,0.469 4.427,0.667 0.313,0.198 10 false *b 1.854,0.417 2.167,0.615 0.313,0.198 10 false B 4.969,0.51 5.281,0.708 0.313,0.198 10 false C 1.031,2.167 1.708,2.385 0.677,0.219 10 false LOLED0 1.76,2.188 2.438,2.406 0.677,0.219 10 false LOLED2
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to Headlight LED Unit Assembly RH)




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Wiring Color Condition Specified Condition
B-4 (LOLED2) - C-1 BR Always Below 1 Ω
B-3 (LOLED0) - C-6 W Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG