Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for RHD with Vacuum Brake Booster)
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0376836 BRAKE ACTUATOR(for RHD with Vacuum Brake Booster) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for RHD with Vacuum Brake Booster)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

The parking brake indicator light blinks (red) when the ignition switch is turned to ON after replacing the brake actuator assembly. Operate the electric parking brake switch assembly to turn off the parking brake indicator light.


PROCEDURE

Hide 44547B 1.INSTALL BRAKE ACTUATOR BRACKET CUSHION

a.

Install the 3 brake actuator bracket cushions to the brake actuator bracket assembly.


b.

Install the 3 No. 1 brake actuator case collars to the brake actuator bracket cushion.

NOTICE:

Make sure that the No. 1 brake actuator case collar is in full contact with the brake actuator bracket cushion.



c.

Install the brake actuator bracket assembly with the 3 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 44510 2.INSTALL BRAKE ACTUATOR ASSEMBLY

a.

Temporarily install the brake actuator assembly to the brake actuator bracket assembly with the 3 bolts.


b.
C407941N01
1.698,1.938 1.854,2.135 0.156,0.198 10 true 1 2.021,1.729 2.177,1.927 0.156,0.198 10 true 2 2.594,1.604 2.75,1.802 0.156,0.198 10 true 3

Tighten the 3 bolts in the order shown in the illustration.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)

NOTICE:
·

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake tubes because the brake actuator assembly is filled with brake fluid.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator assembly when carrying it.

·

Make sure that the brake actuator assembly is in full contact with the brake actuator bracket assembly.




Hide 3.INSTALL BRAKE ACTUATOR WITH BRACKET

a.
C407933

Engage the clamp to install a new brake tube clamp to brake actuator bracket assembly.


b.
C407934

for Manual Transaxle:

i.

Engage the clamp to install a new clutch master cylinder tube clamp to the brake actuator bracket assembly.



c.
C407932N01
0.875,1.583 1.052,1.771 0.177,0.188 10 true 1 2.125,1.594 2.26,1.75 0.135,0.156 10 true 3 2.969,1.156 3.104,1.313 0.135,0.156 10 true 2

Temporarily install the brake actuator with bracket to the vehicle body with the 2 bolts and nut.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Install the brake actuator with bracket while avoiding the brake lines.



d.

Fully tighten the 2 bolts and nut in the order shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


e.
C407930

Engage the clamp to connect the brake lines to the brake tube clamp.


f.
C407931

for Manual Transaxle:

i.

Engage the clamp to connect the clutch master cylinder to flexible hose tube to the clutch master cylinder tube clamp.



g.
C407937

Engage the 5 clamps to install a new brake tube clamp to the brake lines.


h.
C407936C02
1.875,0.865 2.281,0.271 2.281,0.271 2.385,0.271 true 0.813,1.552 0.885,1.552 0.885,1.552 1.396,1.188 true 1.302,0.271 1.51,0.271 1.51,0.271 1.677,0.958 true 1.271,1.573 1.479,1.573 1.479,1.573 1.563,1.115 true 1.49,1.958 1.594,1.958 1.594,1.958 1.688,1.385 true 1.979,1.135 2.573,0.844 2.573,0.844 2.677,0.844 true 2.729,0.75 2.896,0.917 0.167,0.167 10 true *a 1.271,1.865 1.448,2.031 0.177,0.167 10 true *b 2.448,0.177 2.625,0.344 0.177,0.167 10 true *c 1.094,0.188 1.26,0.354 0.167,0.167 10 true *d 1.052,1.49 1.229,1.656 0.177,0.167 10 true *e 0.573,1.458 0.74,1.625 0.167,0.167 10 true *f
*a From 1st Chamber of Brake Master Cylinder Sub-assembly
*b From 2nd Chamber of Brake Master Cylinder Sub-assembly
*c To Front Wheel Cylinder Assembly RH
*d To Rear Wheel Cylinder Assembly LH
*e To Rear Wheel Cylinder Assembly RH
*f To Front Wheel Cylinder Assembly LH


Temporarily tighten the 6 brake lines to the correct positions on the brake actuator assembly as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




i.
C408155C02
2.729,2.656 2.865,3.063 2.865,3.063 2.938,3.063 false 1.771,2.938 2.083,3.094 0.313,0.156 10 false *a 2.979,2.979 3.292,3.135 0.313,0.156 10 false *b 0.938,1.333 1.083,1.5 0.146,0.167 10 true A 1.125,0.771 1.271,0.938 0.146,0.167 10 true A 1.615,0.469 1.76,0.635 0.146,0.167 10 true A 1.885,0.406 2.021,0.573 0.135,0.167 10 true A 2.198,0.75 2.344,0.917 0.146,0.167 10 true B 1.323,1.677 1.469,1.844 0.146,0.167 10 true B
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten each brake line.

Torque:
Specified tightening torque (A) : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)
Specified tightening torque (B) : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow the brake tubes to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tubes from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

(A): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

(B): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




j.
C408156C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake actuator assembly and lock the lock lever.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the actuator connector can be connected smoothly.

·

Do not allow water, oil or dirt to enter the connector.




Hide 55704B 7.INSTALL COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 8.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

HINT:

Use the same procedure as for LHD.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION


Hide 9. ACCELERATION SENSOR ZERO POINT CALIBRATION AND STORE SYSTEM INFORMATION MEMORIZATION

Hide 12.PERFORM INITIALIZATION

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (w/ Vacuum Brake Booster)>PRECAUTION

HINT:

The parking brake indicator light blinks (red) when the ignition switch is turned to ON after replacing the brake actuator assembly. Operate the electric parking brake switch assembly to turn off the parking brake indicator light.