Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for LHD with Vacuum Brake Booster) › 2018.10–2020.08
RM3620E _54 Brake _076411 BRAKE SYSTEM (OTHER) _0377037 BRAKE BOOSTER(for LHD with Vacuum Brake Booster) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for LHD with Vacuum Brake Booster)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake booster assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:
(Click here)
for M20A-FKS:
(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:
·

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Make sure to release vacuum from the brake booster assembly before removing the brake master cylinder sub-assembly from the brake booster assembly.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.


Hide 47201 2.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY

Hide 73900 5.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 87211 6.REMOVE NO. 1 AIR DUCT

Hide 84340 7.REMOVE STOP LIGHT SWITCH ASSEMBLY

Hide 9.SEPARATE WIRE HARNESS

a.
C406469

Disconnect the connector.


b.

Disengage the 2 clamps to separate the wire harness from the brake pedal support assembly.


Hide 10.LOOSEN LOCK NUT

a.
C406555C01
1.01,1.74 1.104,1.74 1.104,1.74 1.667,1.073 true 2.896,1.813 2.771,1.813 2.771,1.813 1.99,1.177 true 0.792,1.667 1.01,1.854 0.219,0.188 10 true *1 2.948,1.74 3.135,1.917 0.188,0.177 10 true *2
*1 Lock Nut
*2 Brake Master Cylinder Push Rod Clevis


Loosen the lock nut of the brake master cylinder push rod clevis.


Hide 44772 12.DISCONNECT CHECK VALVE TO CONNECTOR TUBE HOSE

a.
C406551

Slide the clip and disconnect the check valve to connector tube hose from the brake booster assembly.


Hide 44610 13.REMOVE BRAKE BOOSTER ASSEMBLY

a.
C406550

Remove the bolt and nut.


b.

Disengage the guide and separate the wire harness.


c.
C406556C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the vehicle body as shown in the illustration.


d.
C406552

Disconnect the connector from the vacuum warning switch assembly.


e.
C406553

w/ Stop and Start System:

i.

Disconnect the connector from the vacuum sensor assembly.



f.
C406561

Disengage the 5 clamps to separate the brake tube clamp from the brake lines.


g.
C406560

Disengage the 5 clamps to remove the brake tube clamp from the brake lines.


h.
C406559

Disengage the 5 clamps to remove the brake tube clamp from the brake lines.


i.
C406558

Disengage the 3 clamps to separate the brake tube clamp from the brake lines.


j.

Remove the bolt and clamp to remove the 2 brake tube clamps from the vehicle body.

C406562


k.
C406554C02
0.833,0.25 1,0.25 1,0.25 1.469,0.708 true 0.74,0.667 0.906,0.667 0.906,0.667 1.406,0.969 true 0.646,0.156 0.854,0.365 0.208,0.208 10 true *a 0.542,0.573 0.75,0.781 0.208,0.208 10 true *b
*a From 1st Chamber of Brake Master Cylinder Sub-assembly
*b From 2nd Chamber of Brake Master Cylinder Sub-assembly


Using a union nut wrench, remove the 2 brake lines from the brake actuator assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




l.
C406557

Remove the 4 nuts.

NOTICE:

Do not apply excessive force to the brake lines.



m.

Remove the brake master cylinder push rod clevis and lock nut from the brake booster assembly.


n.

Remove the brake booster assembly from the vehicle body.

NOTICE:

Do not apply excessive force to the brake lines.



Hide 44785 14.REMOVE BRAKE BOOSTER GASKET

a.

Remove the brake booster gasket from the brake booster assembly.