Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM (w/o Occupant Classification System)
RM3620E _58 Vehicle Interior _076406 SEAT BELT _0374978 SEAT BELT WARNING SYSTEM(w/o Occupant Classification System) J

SEAT BELT  SEAT BELT WARNING SYSTEM(w/o Occupant Classification System)  Driver Side Seat Belt Warning Light does not Operate  


DESCRIPTION

The seat belt warning light on the combination meter assembly illuminates, blinks or turns off in accordance with the state of the front seat inner belt assembly (for Driver Side).

WIRING DIAGRAM

E414182E01
3.01,0.865 3.208,1.031 0.198,0.167 10 false 33 4.271,1 4.667,1.385 0.396,0.385 10 false DBKL 5.906,2.146 7.104,2.646 1.198,0.5 10 false Combination Meter Assembly 0.813,3.344 2.531,3.552 1.719,0.208 10 false : CAN Communication Line 3.99,0.844 4.188,1.073 0.198,0.229 10 false 18 1.865,0.854 2.063,1.125 0.198,0.271 10 false 3 0.583,0.875 0.823,1.219 0.24,0.344 10 false 2 3.813,2.302 5.458,2.677 1.646,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 0.208,1.417 1.281,1.76 1.073,0.344 10 false N36*1, M38*2 0.208,1.583 2.146,2.063 1.938,0.479 10 false Front Seat Inner Belt Assembly (for Driver Side) 2.51,1.573 4.135,2.115 1.625,0.542 10 false Instrument Panel Junction Block Assembly 0.375,2.927 3.563,3.271 3.188,0.344 10 false *2: for RHD 0.385,2.573 3.573,2.917 3.188,0.344 10 false *1: for LHD 3.833,2.115 4.104,2.354 0.271,0.24 10 false A 1.573,1.094 1.729,1.292 0.156,0.198 10 false + 0.823,1.115 0.979,1.313 0.156,0.198 10 false E 1.438,2.573 4.625,2.917 3.188,0.344 10 false *3: for LHD, Manual Transaxle 1.396,2.917 4.583,3.26 3.188,0.344 10 false *4: except LHD, Manual Transaxle 2.521,1.396 4.667,1.594 2.146,0.198 10 false 4N*3, 4H*4

CAUTION / NOTICE / HINT

NOTICE:

The seat belt warning system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM (w/o Occupant Classification System)>HOW TO PROCEED WITH TROUBLESHOOTING


HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat. Check that the operation of the seat belt warning light is normal first.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM (w/o Occupant Classification System)>OPERATION CHECK

If the seat belt warning light does not operate for both the driver seat and front passenger seat, replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


PROCEDURE

1.READ VALUE USING GTS (D SEAT BUCKLE SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Seat Buckle SW Driver seat belt buckle switch OFF or ON OFF: Driver seat belt unfastened
ON: Driver seat belt fastened
-
Body Electrical > Main Body > Data List
Tester Display
D Seat Buckle SW
50003 123 14
OK:

ON or OFF appears on the GTS screen according to the driver seat belt condition.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER SIDE)
2.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER SIDE)
a.

Remove the front seat inner belt assembly (for Driver Side).



b.

Inspect the front seat inner belt assembly (for Driver Side).



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER SIDE) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER SIDE)

3.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER SIDE) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)

*1: for LHD

*2: for RHD

*3: for Manual Transaxle

*4: except Manual Transaxle


a.

Disconnect the N36*1 or M38*2 front seat inner belt assembly (for Driver Side) connector.


b.

Disconnect the 4N*3 or 4H*4 instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD, Manual Transaxle
Tester Connection Condition Specified Condition
4N-33 - N36-3 (+) Always Below 1 Ω
N36-3 (+) or 4N-33 - Body ground Always 10 kΩ or higher
N36-2 (E) - Body ground Always Below 1 Ω

for LHD, except Manual Transaxle
Tester Connection Condition Specified Condition
4H-33 - N36-3 (+) Always Below 1 Ω
N36-3 (+) or 4H-33 - Body ground Always 10 kΩ or higher
N36-2 (E) - Body ground Always Below 1 Ω

except LHD, Manual Transaxle
Tester Connection Condition Specified Condition
4H-33 - M38-3 (+) Always Below 1 Ω
M38-3 (+) or 4H-33 - Body ground Always 10 kΩ or higher
M38-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.


B491251C10
1.948,0.719 2.365,0.958 0.417,0.24 5.552,0.625 5.948,0.865 0.396,0.24 5.552,0.229 5.948,0.469 0.396,0.24 2.427,1.979 2.427,1.552 false 5.667,0.656 5.979,0.854 0.313,0.198 10 false 4H 2.115,0.76 2.427,0.958 0.313,0.198 10 false A 0.344,0.167 0.656,0.365 0.313,0.198 10 false *a 2.25,2 2.865,2.198 0.615,0.198 10 false DBKL 5.667,0.26 5.979,0.458 0.313,0.198 10 false 4N 6.073,0.26 6.385,0.458 0.313,0.198 10 false *A 6.073,0.646 6.385,0.844 0.313,0.198 10 false *B
*A for LHD, Manual Transaxle *B except LHD, Manual Transaxle
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD, Manual Transaxle
Tester Connection Condition Specified Condition
A-18 (DBKL) - 4N-33 Always Below 1 Ω

except LHD, Manual Transaxle
Tester Connection Condition Specified Condition
A-18 (DBKL) - 4H-33 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG