Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM (w/o Occupant Classification System)
RM3620E _58 Vehicle Interior _076406 SEAT BELT _0374978 SEAT BELT WARNING SYSTEM(w/o Occupant Classification System) J

SEAT BELT  SEAT BELT WARNING SYSTEM(w/o Occupant Classification System)  Rear Seat Belt Warning Light Malfunction  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects whether either the rear doors are open or closed based on the courtesy light switch condition and then sends the rear door status signal to the combination meter assembly. The combination meter assembly detects the rear seat belt state. The rear seat belt warning light on the combination meter assembly illuminates, blinks or turns off in accordance with the rear door state, vehicle speed and rear seat belt state.

WIRING DIAGRAM

w/o Rear Seat Occupant Detection Sensor:
E414184E01
5.188,0.521 5.802,0.719 0.615,0.198 10 false RLSB 5.219,1.031 5.833,1.229 0.615,0.198 10 false RCSB 5.208,2.302 5.823,2.5 0.615,0.198 10 false RRSB 4.917,0.979 5.229,1.177 0.313,0.198 10 false 19 4.906,0.427 5.219,0.625 0.313,0.198 10 false 36 4.917,2.229 5.229,2.427 0.313,0.198 10 false 35 3.75,0.375 4.063,0.573 0.313,0.198 10 false 5 2.344,2.219 2.656,2.417 0.313,0.198 10 false 4 3.208,0.427 3.625,0.625 0.417,0.198 10 false LBR+ 2.521,0.438 2.938,0.635 0.417,0.198 10 false LBR- 2.542,0.979 2.958,1.177 0.417,0.198 10 false CBR- 3.208,0.948 3.625,1.146 0.417,0.198 10 false CBR+ 2.302,0.365 2.615,0.563 0.313,0.198 10 false 4 3.708,2.25 4.021,2.448 0.313,0.198 10 false 5 2.198,2.906 4.271,3.198 2.073,0.292 10 false Rear Seat Inner Belt Assembly 2.219,2.75 2.833,2.948 0.615,0.198 10 false N37 2.281,1.583 3.99,1.948 1.708,0.365 10 false Rear Seat Inner with Center Belt Assembly LH 2.208,0.885 2.521,1.083 0.313,0.198 10 false 3 3.208,2.24 3.625,2.438 0.417,0.198 10 false RBR+ 2.542,2.24 2.958,2.438 0.417,0.198 10 false RBR- 0.5,5.323 3.635,5.594 3.135,0.271 10 false M5 2.198,3.74 2.51,3.938 0.313,0.198 10 false 1 3.25,3.854 3.865,4.052 0.615,0.198 10 false 4H 3.646,4.896 4.26,5.094 0.615,0.198 10 false 4A 3.24,3.667 3.854,3.865 0.615,0.198 10 false 24 3.635,4.708 4.25,4.906 0.615,0.198 10 false 31 4.917,3.76 5.229,3.958 0.313,0.198 10 false 13 4.99,4.771 5.302,4.969 0.313,0.198 10 false 2 5.188,3.802 5.802,4 0.615,0.198 10 false LCTY 5.198,4.885 5.813,5.083 0.615,0.198 10 false RCTY 3.49,5.323 5.094,5.885 1.604,0.563 10 false Instrument Panel Junction Block Assembly 4.792,2.813 6.104,3.156 1.313,0.344 10 false G19 3.677,1.073 4.135,1.271 0.458,0.198 10 false N39 2.156,1.063 2.615,1.26 0.458,0.198 10 false N39 3.667,0.552 4.125,0.75 0.458,0.198 10 false N38 2.156,0.542 2.615,0.74 0.458,0.198 10 false N38 3.781,0.896 4.094,1.094 0.313,0.198 10 false 4 4.771,2.99 6.604,3.281 1.833,0.292 10 false Combination Meter Assembly 2.208,4.802 2.521,5 0.313,0.198 10 false 1 0.51,5.49 3.646,5.76 3.135,0.271 10 false Rear Door Courtesy Light Switch Assembly RH 0.635,4.25 3.771,4.521 3.135,0.271 10 false N8 3.688,3.688 4.302,3.885 0.615,0.198 10 false 24 3.625,3.854 4.24,4.052 0.615,0.198 10 false 4N 3.24,4.052 4.073,4.323 0.833,0.271 10 false *1 3.635,4.052 4.469,4.323 0.833,0.271 10 false *2 0.594,4.396 3.729,4.667 3.135,0.271 10 false Rear Door Courtesy Light Switch Assembly LH 4.885,5.927 6.521,6.26 1.635,0.333 10 false A 4.865,6.073 6.5,6.406 1.635,0.333 10 false Main Body ECU (Multiplex Network Body ECU) 0.99,6.406 4.125,6.677 3.135,0.271 10 false : CAN Communication Line 2.813,0.708 3.385,0.969 0.573,0.26 10 false (for LH) 2.729,1.24 3.479,1.563 0.75,0.323 10 false (for Center) 0.271,5.833 3.406,6.104 3.135,0.271 10 false *1: except Manual Transaxle 0.271,6.125 3.406,6.396 3.135,0.271 10 false *2: for Manual Transaxle

w/ Rear Seat Occupant Detection Sensor:
E414185E01
2.875,6.438 4.208,6.833 1.333,0.396 10 false Rear Seat Inner Belt Assembly 5.708,6.375 6.958,6.771 1.25,0.396 10 false G19 5.708,6.542 6.958,6.938 1.25,0.396 10 false Combination Meter Assembly 5.969,4.917 6.885,5.24 0.917,0.323 10 false RRSB 5.948,2.458 6.865,2.781 0.917,0.323 10 false RCSB 5.958,1.031 6.875,1.354 0.917,0.323 10 false RLSB 4.146,1.042 5.063,1.365 0.917,0.323 10 false N38 4.24,0.854 5.156,1.177 0.917,0.323 10 false 5 4.229,1.521 5.146,1.844 0.917,0.323 10 false 4 4.229,2.26 5.146,2.583 0.917,0.323 10 false 4 4.24,5.438 5.156,5.76 0.917,0.323 10 false 4 4.24,4.771 5.156,5.094 0.917,0.323 10 false 5 4.219,2.969 5.135,3.292 0.917,0.323 10 false 3 4.146,1.708 5.063,2.031 0.917,0.323 10 false N38 4.135,2.469 5.052,2.792 0.917,0.323 10 false N39 4.135,3.146 5.052,3.469 0.917,0.323 10 false N39 4.146,4.969 5.063,5.292 0.917,0.323 10 false N37 4.146,5.646 5.063,5.969 0.917,0.323 10 false N37 2.635,1.042 3.552,1.365 0.917,0.323 10 false z15 2.646,1.698 3.563,2.021 0.917,0.323 10 false z15 2.625,2.469 3.542,2.792 0.917,0.323 10 false z16 2.635,3.125 3.552,3.448 0.917,0.323 10 false z16 2.625,4.969 3.542,5.292 0.917,0.323 10 false z17 2.625,5.625 3.542,5.948 0.917,0.323 10 false z17 2.698,5.458 3.615,5.781 0.917,0.323 10 false 2 2.698,2.948 3.615,3.271 0.917,0.323 10 false 2 2.719,1.5 3.635,1.823 0.917,0.323 10 false 2 2.688,0.833 3.604,1.156 0.917,0.323 10 false 1 2.688,2.271 3.604,2.594 0.917,0.323 10 false 1 2.688,4.781 3.604,5.104 0.917,0.323 10 false 1 3.177,2.656 4.094,2.979 0.917,0.323 10 false (for Center) 3.198,1.229 4.115,1.552 0.917,0.323 10 false (for LH) 0.792,6.396 2.583,6.771 1.792,0.375 10 false Rear Seat Cushion Pad 0.74,5.979 2.531,6.354 1.792,0.375 10 false Occupant Detection Sensor 0.75,3.51 2.542,3.885 1.792,0.375 10 false Occupant Detection Sensor 0.771,2.094 2.563,2.469 1.792,0.375 10 false Occupant Detection Sensor 5.646,4.844 6.563,5.167 0.917,0.323 10 false 35 5.656,2.354 6.573,2.677 0.917,0.323 10 false 19 5.646,0.906 6.563,1.229 0.917,0.323 10 false 36 2.677,3.823 4.406,4.229 1.729,0.406 10 false Rear Seat Inner with Center Belt Assembly LH 3.635,2.281 4.552,2.604 0.917,0.323 10 false CBR+ 3.656,3.042 4.573,3.365 0.917,0.323 10 false CBR- 3.677,4.833 4.594,5.156 0.917,0.323 10 false RBR+ 3.698,5.542 4.615,5.865 0.917,0.323 10 false RBR- 3.667,0.896 4.583,1.219 0.917,0.323 10 false LBR+ 3.677,1.615 4.594,1.938 0.917,0.323 10 false LBR-

CAUTION / NOTICE / HINT

NOTICE:
·

The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM (w/o Occupant Classification System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.SYSTEM CHECK
a.

Check the vehicle specification.


Result:
Result Proceed to
w/o Rear Occupant Detection Sensor A
w/ Rear Occupant Detection Sensor B



A

2.READ VALUE USING GTS

B

3.READ VALUE USING GTS
2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door Courtesy SW Rear door courtesy light switch RH signal OFF or ON OFF: Rear door RH closed
ON: Rear door RH open
-
RL Door Courtesy SW Rear door courtesy light switch LH signal OFF or ON OFF: Rear door LH closed
ON: Rear door LH open
-
Body Electrical > Main Body > Data List
Tester Display
RR Door Courtesy SW
RL Door Courtesy SW
50003 123 24,25
OK:

The GTS display changes correctly in response to the rear door condition.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS

NG

3.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Right Seat Buckle / Occupant Detection Warning Switch Rear seat inner belt buckle signal ON or OFF
w/o Rear Seat Occupant Detection Sensor

OFF: Rear RH seat belt fastened

ON: Rear RH seat belt not fastened


w/ Rear Seat Occupant Detection Sensor

OFF: Rear RH seat belt fastened and occupied

ON: Rear RH seat belt not fastened and occupied


-
Rear Left Seat Buckle / Occupant Detection Warning Switch Rear seat inner with center belt LH (for LH) buckle signal ON or OFF
w/o Rear Seat Occupant Detection Sensor

OFF: Rear LH seat belt (for LH) fastened

ON: Rear LH seat belt (for LH) not fastened


w/ Rear Seat Occupant Detection Sensor

OFF: Rear LH seat belt (for LH) fastened and occupied

ON: Rear LH seat belt (for LH) not fastened and occupied


-
Rear Center Seat Buckle / Occupant Detection Warning Switch Rear seat inner with center belt LH (for Center) buckle signal ON or OFF
w/o Rear Seat Occupant Detection Sensor

OFF: Rear LH seat belt (for Center) fastened

ON: Rear LH seat belt (for Center) not fastened


w/ Rear Seat Occupant Detection Sensor

OFF: Rear LH seat belt (for Center) fastened and occupied

ON: Rear LH seat belt (for Center) not fastened and occupied


-
Body Electrical > Combination Meter > Data List
Tester Display
Rear Right Seat Buckle / Occupant Detection Warning Switch
Rear Left Seat Buckle / Occupant Detection Warning Switch
Rear Center Seat Buckle / Occupant Detection Warning Switch
50003 409 30,31,32

Result:
Result Proceed to
All item is normal A
"Rear Right Seat Buckle / Occupant Detection Warning Switch" item does not switch to "ON" or "OFF" according to the rear seat belt condition (w/o Rear Seat Occupant Detection Sensor) B
"Rear Left Seat Buckle / Occupant Detection Warning Switch" item does not switch to "ON" or "OFF" according to the rear LH seat belt condition (w/o Rear Seat Occupant Detection Sensor) C
"Rear Center Seat Buckle / Occupant Detection Warning Switch" item does not switch to "ON" or "OFF" according to the rear LH seat belt condition (w/o Rear Seat Occupant Detection Sensor) D
"Rear Right Seat Buckle / Occupant Detection Warning Switch" item does not switch to "ON" or "OFF" according to the rear seat belt condition (w/ Rear Seat Occupant Detection Sensor) E
"Rear Left Seat Buckle / Occupant Detection Warning Switch" item does not switch to "ON" or "OFF" according to the rear LH seat belt condition (w/ Rear Seat Occupant Detection Sensor) F
"Rear Center Seat Buckle / Occupant Detection Warning Switch" item does not switch to "ON" or "OFF" according to the rear LH seat belt condition (w/ Rear Seat Occupant Detection Sensor) G



A

REPLACE COMBINATION METER ASSEMBLY

B

4.INSPECT REAR SEAT INNER BELT ASSEMBLY

C

6.INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

D

8.INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

E

10.INSPECT REAR SEAT INNER BELT ASSEMBLY

F

13.INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

G

16.INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH
4.INSPECT REAR SEAT INNER BELT ASSEMBLY
a.

Remove the rear seat inner belt assembly.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY>REMOVAL


b.

Inspect the rear seat inner belt assembly.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPLACE REAR SEAT INNER BELT ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the N37 rear seat inner belt assembly connector.


b.

Disconnect the G19 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N37-5 (RBR+) - G19-35 (RRSB) Always Below 1 Ω
N37-5 (RBR+) or G19-35 (RRSB) - Body ground Always 10 kΩ or higher
N37-4 (RBR-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH
a.

Remove the rear seat inner with center belt assembly LH.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY>REMOVAL


b.

Inspect the rear seat inner with center belt assembly LH.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

7.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the N38 rear seat inner with center belt assembly LH connector.


b.

Disconnect the G19 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N38-5 (LBR+) - G19-36 (RLSB) Always Below 1 Ω
N38-5 (LBR+) or G19-36 (RLSB) - Body ground Always 10 kΩ or higher
N38-4 (LBR-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH
a.

Remove the rear seat inner with center belt assembly LH.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY>REMOVAL


b.

Inspect the rear seat inner with center belt assembly LH.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

9.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the N39 rear seat inner with center belt assembly LH connector.


b.

Disconnect the G19 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N39-4 (CBR+) - G19-19 (RCSB) Always Below 1 Ω
N39-4 (CBR+) or G19-19 (RCSB) - Body ground Always 10 kΩ or higher
N39-3 (CBR-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT REAR SEAT INNER BELT ASSEMBLY
a.

Remove the rear seat inner belt assembly.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY>REMOVAL


b.

Inspect the rear seat inner belt assembly.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

11.INSPECT REAR SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)

NG

REPLACE REAR SEAT INNER BELT ASSEMBLY

11.INSPECT REAR SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)
a.

Remove the rear seat cushion pad (occupant detection sensor).

Click hereVehicle Interior>SEAT>OCCUPANT DETECTION SENSOR(for Rear Seat)>REMOVAL


b.

Inspect the rear seat cushion pad (occupant detection sensor).

Click hereVehicle Interior>SEAT>OCCUPANT DETECTION SENSOR(for Rear Seat)>INSPECTION


Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPLACE REAR SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)

12.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the N37 rear seat inner belt assembly connector.


b.

Disconnect the G19 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N37-5 (RBR+) - G19-35 (RRSB) Always Below 1 Ω
N37-5 (RBR+) or G19-35 (RRSB) - Body ground Always 10 kΩ or higher
N37-4 (RBR-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH
a.

Remove the rear seat inner with center belt assembly LH.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY>REMOVAL


b.

Inspect the rear seat inner with center belt assembly LH.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

14.INSPECT REAR SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)

NG

REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

14.INSPECT REAR SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)
a.

Remove the rear seat cushion pad (occupant detection sensor).

Click hereVehicle Interior>SEAT>OCCUPANT DETECTION SENSOR(for Rear Seat)>REMOVAL


b.

Inspect the rear seat cushion pad (occupant detection sensor).

Click hereVehicle Interior>SEAT>OCCUPANT DETECTION SENSOR(for Rear Seat)>INSPECTION


Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPLACE REAR SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)

15.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the N38 rear seat inner with center belt assembly LH connector.


b.

Disconnect the G19 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N38-5 (LBR+) - G19-36 (RLSB) Always Below 1 Ω
N38-5 (LBR+) or G19-36 (RLSB) - Body ground Always 10 kΩ or higher
N38-4 (LBR-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH
a.

Remove the rear seat inner with center belt assembly LH.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY>REMOVAL


b.

Inspect the rear seat inner with center belt assembly LH.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

17.INSPECT REAR SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)

NG

REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

17.INSPECT REAR SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)
a.

Remove the rear seat cushion pad (occupant detection sensor).

Click hereVehicle Interior>SEAT>OCCUPANT DETECTION SENSOR(for Rear Seat)>REMOVAL


b.

Inspect the rear seat cushion pad (occupant detection sensor).

Click hereVehicle Interior>SEAT>OCCUPANT DETECTION SENSOR(for Rear Seat)>INSPECTION


Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPLACE REAR SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)

18.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the N39 rear seat inner with center belt assembly LH connector.


b.

Disconnect the G19 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N39-4 (CBR+) - G19-19 (RCSB) Always Below 1 Ω
N39-4 (CBR+) or G19-19 (RCSB) - Body ground Always 10 kΩ or higher
N39-3 (CBR-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR