Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ Vacuum Brake Booster)
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379311 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/ Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/ Vacuum Brake Booster)  P057112  Brake Switch "A" Circuit Short to Battery  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives stop light switch assembly signals and uses them to determine whether or not the brakes are applied.

DTCs may be stored if either of the following occurs:

·

Stop light switch assembly stuck on malfunction.

·

The accelerator and brake pedals are depressed simultaneously.*


HINT:

*: The skid control ECU (brake actuator assembly) may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously. However, this does not indicate a malfunction.


DTC No. Detection Item DTC Detection Condition Trouble Area
P057112 Brake Switch "A" Circuit Short to Battery The vehicle speed is 10 km/h (6 mph) or more, the accelerator pedal is depressed, the master cylinder pressure is 0.5 MPa (5.1 kgf/cm2, 72.5 psi) or less, and the stop light switch assembly is on for 60 seconds or more.
·

Stop light switch assembly

·

Stop light switch assembly installation

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)

·

ECM

·

Shift lock control ECU (shift lock control unit assembly)

·

Certification ECU (smart key ECU assembly)

·

TCM*



*: for Continuously Variable Transaxle

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ Vacuum Brake Booster)>UTILITY

·

DTC precaution

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ Vacuum Brake Booster)>PRECAUTION

Procedure to Clear Warning Lights (When not Clearing DTCs)
Procedure
1.

Repair or replacement.

2.

Turn the ignition switch to ON.

3.

Drive the vehicle and depress the brake pedal 2 or 3 times to clear the warning lights.





PROCEDURE

1.CHECK BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Check the brake pedal height and stop light switch assembly installation.

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for LHD with Vacuum Brake Booster)>ADJUSTMENT

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(for RHD with Vacuum Brake Booster)>ADJUSTMENT

OK:

The brake pedal height and stop light switch assembly installation are normal.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY OUTPUT CIRCUIT)

NG

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY OUTPUT CIRCUIT)
a.
C401043C23
0.396,0.667 0.833,0.927 0.438,0.26 2.167,1.677 1.854,1.052 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 2.177,1.708 2.333,1.906 0.156,0.198 10 false L 0.49,0.729 0.979,1.063 0.49,0.333 10 false A40
*a Component with harness connected
(Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-3 (L) - Body ground Brake pedal released Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.
A418954C29
1.5,0.25 1.917,0.5 0.417,0.25 1.281,1.854 1.531,1.354 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.583,0.292 2.042,0.49 0.458,0.198 10 false A40 1.198,1.854 1.375,2.073 0.177,0.219 10 false L
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A40 stop light switch assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-3 (L) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.
A418954C29
1.5,0.25 1.917,0.5 0.417,0.25 1.281,1.854 1.531,1.354 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.583,0.292 2.042,0.49 0.458,0.198 10 false A40 1.198,1.854 1.375,2.073 0.177,0.219 10 false L
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A40 stop light switch assembly connector.


d.

Disconnect the A24 ECM connector.


e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-3 (L) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SHIFT LOCK CONTROL UNIT ASSEMBLY)
5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.
A418954C29
1.5,0.25 1.917,0.5 0.417,0.25 1.281,1.854 1.531,1.354 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.583,0.292 2.042,0.49 0.458,0.198 10 false A40 1.198,1.854 1.375,2.073 0.177,0.219 10 false L
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A40 stop light switch assembly connector.


d.

Disconnect the A24 ECM connector.


e.

w/ Entry and Start System:

Disconnect the G26 shift lock control ECU (shift lock control unit assembly) connector.


f.

w/o Entry and Start System:

Disconnect the G27 shift lock control ECU (shift lock control unit assembly) connector.


g.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-3 (L) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SMART KEY ECU ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SMART KEY ECU ASSEMBLY)
a.
A418954C29
1.5,0.25 1.917,0.5 0.417,0.25 1.281,1.854 1.531,1.354 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.583,0.292 2.042,0.49 0.458,0.198 10 false A40 1.198,1.854 1.375,2.073 0.177,0.219 10 false L
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A40 stop light switch assembly connector.


d.

Disconnect the A24 ECM connector.


e.

w/ Entry and Start System:

Disconnect the G26 shift lock control ECU (shift lock control unit assembly) connector.


f.

w/o Entry and Start System:

Disconnect the G27 shift lock control ECU (shift lock control unit assembly) connector.


g.

Disconnect the M7 certification ECU (smart key ECU assembly) connector.


h.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-3 (L) - Body ground Always Below 1.5 V



Result:
Result Proceed to
OK A
NG (except Continuously Variable Transaxle) B
NG (for Continuously Variable Transaxle) C



A

REPLACE SMART KEY ECU ASSEMBLY

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

7.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)
7.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)
a.
A418954C29
1.5,0.25 1.917,0.5 0.417,0.25 1.281,1.854 1.531,1.354 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.583,0.292 2.042,0.49 0.458,0.198 10 false A40 1.198,1.854 1.375,2.073 0.177,0.219 10 false L
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A40 stop light switch assembly connector.


d.

Disconnect the A24 ECM connector.


e.

w/ Entry and Start System:

Disconnect the G26 shift lock control ECU (shift lock control unit assembly) connector.


f.

w/o Entry and Start System:

Disconnect the G27 shift lock control ECU (shift lock control unit assembly) connector.


g.

Disconnect the M7 certification ECU (smart key ECU assembly) connector.


h.

Disconnect the C33 TCM connector.


i.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



j.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-3 (L) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR