Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379312 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster)  C1247  Stroke Sensor  C1346  Abnormal Learning of Stroke Sensor Zero Point (Test Mode DTC)  C1392  Zero Point Calibration of Stroke Sensor undone  


DESCRIPTION

The brake pedal stroke sensor assembly sends a signal about the pedal stroke to the skid control ECU (brake booster with master cylinder assembly).

DTC C1346 will be cleared when the brake pedal stroke sensor assembly sends a brake pedal stroke sensor assembly signal or when Test Mode ends. DTC C1346 is output only in Test Mode.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1247 Stroke Sensor 211
212
213
214
215
216
217
218
219
220
221
222
223
·

INF Code: 211

-

Sensor supply voltage (VCM1) is 4.75 V or less, or 5.25 V or more for 0.2 seconds or more.


·

INF Code: 212

-

Sensor output voltage 1 (SKS1) is less than 5.5%, or 94% or more (less than 0.27 V, or 4.7 V or more) of sensor supply voltage (VCM1) for 0.2 seconds or more.


·

INF Code: 213

-

Sensor output voltage 2 (SKS2) is less than 5.5%, or 94% or more (less than 0.27 V, or 4.7 V or more) of sensor supply voltage (VCSK) for 0.2 seconds or more.


·

INF Code: 214

-

Either of the following is detected:

(1)

Fluctuation of sensor output 1 (SKS1) is out of specification.

(2)

The difference between the present value and last value of sensor output voltage 1 (SKS1) is 8.5% or more (0.43 V or more) of sensor supply voltage (VCM1) for 0.2 seconds or more.



·

INF Code: 215

-

Either of the following is detected:

(1)

Fluctuation of sensor output 2 (SKS2) is out of specification.

(2)

The difference between the present value and last value of the sensor output voltage 2 (SKS2) is 8.5% or more (0.43 V or more) of the sensor supply voltage (VCM1) for 0.2 seconds or more.



·

INF Code: 216

-

Either of the following is detected:

(1)

Pedal off position (zero point stored value) is out of specification.

(2)

The zero point stored value for the sensor output voltage 1 (SKS1) is deviates -17% to 25.9% (0.15 to 2.3 V) or more from the theoretical value.



·

INF Code: 217

-

Either of the following is detected:

(1)

Pedal off position (zero point stored value) is out of specification.

(2)

The zero point stored value for the sensor output voltage 2 (SKS2) deviates -31.7% to 17% (2.42 to 4.85 V) or more from the theoretical value.



·

INF Code: 218

-

An excessive difference between the change in sensor output 1 (SKS1) and sensor output 2 (SKS2) is detected for 0.2 seconds or more.


·

INF Code: 219

-

Sensor data is invalid for 0.2 seconds or more.

(Skid control ECU (Brake booster with master cylinder assembly) internal monitor circuit malfunction.)


·

INF Code: 220

-

The sum of sensor output voltage 1 (SKS1) and sensor output voltage 2 (SKS2) deviates 15% or more from the theoretical value 5 V.


·

INF Code: 221

-

An excessive difference exists between the variation in sensor output voltage 1 (SKS1) and sensor output voltage 2 (SKS2).


·

INF Code: 222

-

Sensor power source voltage (VCM1) remains at 4.75 V or less or 5.25 V or more and the sensor data is invalid for 0.2 seconds or longer.


·

INF Code: 223

-

Sensor data is invalid for 0.2 seconds or more.

(Open, short or noise.)



·

INF Code: 211

-

Open or short in brake pedal stroke sensor assembly power supply circuit

-

Improperly connected connector, deformation or corrosion of terminals

-

Skid control ECU (Brake booster with master cylinder assembly)


·

INF Code: 212, 213, 214, 215, 216, 217, 218, 219, 220, 221, 222, 223

-

Open or short in wire harness

-

Improperly connected connector, deformation or corrosion of terminals

-

Brake pedal stroke sensor assembly



-
C1346 Abnormal Learning of Stroke Sensor Zero Point (Test Mode DTC) - Detected only during Test Mode.
·

Brake pedal stroke sensor assembly

·

Brake pedal stroke sensor assembly circuit


-
C1392 Zero Point Calibration of Stroke Sensor undone - Zero point calibration of brake pedal stroke sensor assembly is unfinished.
·

Brake pedal stroke sensor zero point calibration incomplete (Initialization and calibration of linear solenoid valve incomplete)

·

Skid control ECU (Brake booster with master cylinder assembly)


-

DTC Detection Conditions: C1247 INF Code: 214
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status Fluctuation of sensor output 1 (SKS1) is out of specification ○ -
The difference between the present value and last value of the sensor output voltage 1(SKS1) is 8.5% or more (0.43 V or more) of the sensor supply voltage (VCM1) - ○
Detection Time - 0.2 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1247 INF Code: 215
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status Fluctuation of sensor output 2 (SKS2) is out of specification ○ -
The difference between the present value and last value of the sensor output voltage 2(SKS2) is 8.5% or more (0.43 V or more) of the sensor supply voltage (VCM1) - ○
Detection Time - 0.2 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1247 INF Code: 216
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status Pedal off position (zero point stored value) is out of specification ○ -
The zero point stored value for the sensor output voltage 1 (SKS1) is deviates -17% to 25.9% (0.15 to 2.3 V) or more from the theoretical value - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1247 INF Code: 217
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status Pedal off position (zero point stored value) is out of specification ○ -
The zero point stored value for the sensor output voltage 2 (SKS2) deviates -31.7% to 17% (2.42 to 4.85 V) or more from the theoretical value - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C407567E04
0.438,3.927 2.917,4.344 2.479,0.417 10 false Brake Pedal Stroke Sensor Assembly 2.208,1.521 2.99,1.865 0.781,0.344 10 false SKS1 2.167,1.073 3.042,1.396 0.875,0.323 10 false VCSK 2.24,1.938 2.99,2.354 0.75,0.417 10 false SKG 2.188,2.771 3.052,3.115 0.865,0.344 10 false SKS2 5.781,1.521 6.573,2.01 0.792,0.49 10 false SKS 5.771,1.083 6.594,1.438 0.823,0.354 10 false VCSK 5.781,1.958 6.531,2.344 0.75,0.385 10 false SKG 5.771,2.813 6.396,3.177 0.625,0.365 10 false SKS2 2.708,2.75 3.344,3.073 0.635,0.323 10 false 2*1, 4*2 2.708,1.51 3.385,1.854 0.677,0.344 10 false 4*1, 2*2 2.698,1.948 3.281,2.313 0.583,0.365 10 false 1 2.708,1.052 3.313,1.333 0.604,0.281 10 false 3 4.667,3.833 5.26,4.135 0.594,0.302 10 false A42 5.51,1.073 6.188,1.49 0.677,0.417 10 false 39 5.521,1.49 6.083,1.854 0.563,0.365 10 false 42 5.51,1.958 5.885,2.219 0.375,0.26 10 false 41 5.01,3.802 7.094,4.167 2.083,0.365 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.115,3.927 0.667,4.219 0.552,0.292 10 false A41 5.521,2.771 6.083,3.177 0.563,0.406 10 false 40 0.125,4.302 1.177,4.531 1.052,0.229 10 false *1: for LHD 1.208,4.302 2.406,4.552 1.198,0.25 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly) or brake pedal stroke sensor assembly, perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY


HINT:

Check the condition of each related circuit connector before troubleshooting.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


PROCEDURE

1.CHECK BRAKE PEDAL
a.

Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.




Result:
Proceed to
NEXT



NEXT

2.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Disconnect the A41 brake pedal stroke sensor assembly connector.


d.

Check both the connector case and the terminal for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
A42-39 (VCSK) - A41-3 (VCSK) Always Below 1 Ω
A42-39 (VCSK) or A41-3 (VCSK) - Body ground Always 10 kΩ or higher
A42-41 (SKG) - A41-1 (SKG) Always Below 1 Ω
A42-41 (SKG) or A41-1 (SKG) - Body ground Always 10 kΩ or higher
A42-42 (SKS) - A41-4 (SKS1) Always Below 1 Ω
A42-42 (SKS) or A41-4 (SKS1) - Body ground Always 10 kΩ or higher
A42-40 (SKS2) - A41-2 (SKS2) Always Below 1 Ω
A42-40 (SKS2) or A41-2 (SKS2) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
A42-39 (VCSK) - A41-3 (VCSK) Always Below 1 Ω
A42-39 (VCSK) or A41-3 (VCSK) - Body ground Always 10 kΩ or higher
A42-41 (SKG) - A41-1 (SKG) Always Below 1 Ω
A42-41 (SKG) or A41-1 (SKG) - Body ground Always 10 kΩ or higher
A42-42 (SKS) - A41-2 (SKS1) Always Below 1 Ω
A42-42 (SKS) or A41-2 (SKS1) - Body ground Always 10 kΩ or higher
A42-40 (SKS2) - A41-4 (SKS2) Always Below 1 Ω
A42-40 (SKS2) or A41-4 (SKS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
a.
C234579C36
0.302,1.01 0.781,1.344 0.479,0.333 1.25,2.281 0.865,2.823 false 1.698,2.302 2.083,2.844 false 0.281,0.24 0.781,0.677 0.5,0.438 10 false *a 0.385,1.094 1.125,1.552 0.74,0.458 10 false A41 0.688,2.854 1.292,3.125 0.604,0.271 10 false SKG 1.99,2.865 2.813,3.24 0.823,0.375 10 false VCSK
*a Front view of wire harness connector
(to Brake Pedal Stroke Sensor Assembly)


Reconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A41-3 (VCSK) - A41-1 (SKG) Power switch on (IG) 4.84 to 5.16 V



Result:
Proceed to
OK
NG



OK

NG