Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster) › 2018.10–2019.09
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379312 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster)  C1380  Stop Light Control Relay Malfunction  


DESCRIPTION

When any of the following conditions are met, the skid control ECU (brake booster with master cylinder assembly) sets the drive output (STPO) ON which operates the stop light control relay (stop light switch assembly) and turns on the stop lights.

Illumination Conditions:

·

Pre-collision brake is operating.*

·

The dynamic radar cruise control system is operating and is applying the brakes.*

·

Secondary collision brake is operating.

·

Brake hold is operating.


*: w/ Pre-collision System


DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1380 Stop Light Control Relay Malfunction 761
762
·

INF Code: 761

-

When the voltage at terminal IG1 is 9.5 V higher than, stop light drive output (STPO) is ON and STP is OFF for 2 seconds or more.



·

INF Code: 762

-

When the voltage at terminal IG1 is 9.5 V higher than, stop light drive output (STPO) is OFF and the input signals for STP and STP2 differ for 5 seconds or more.



·

Stop light switch assembly circuit

·

Stop light switch assembly

·

Skid control ECU (Brake booster with master cylinder assembly)

·

Hybrid vehicle control ECU assembly

·

Certification ECU (smart key ECU assembly)

·

Rear combination light socket and wire LH

·

Rear combination light socket and wire RH

·

Stop light LED

·

Center stop light cord assembly

·

Center stop light assembly

·

Open or short in wire harness


-

WIRING DIAGRAM

C405822E04
1.542,0.542 2.083,0.802 0.542,0.26 10 false A29 1.573,0.781 4.021,1.094 2.448,0.313 10 false Hybrid Vehicle Control ECU Assembly 2.969,0.333 3.51,0.594 0.542,0.26 10 false STP 3.375,0.229 3.917,0.49 0.542,0.26 10 false 7 4.667,0.219 5.208,0.479 0.542,0.26 10 false 25 4.927,0.344 5.469,0.604 0.542,0.26 10 false STP1 4.271,0.521 4.813,0.781 0.542,0.26 10 false M7 4.281,0.781 7.083,1.073 2.802,0.292 10 false Certification ECU (Smart Key ECU Assembly) 1.156,1.188 2.667,1.552 1.51,0.365 10 false from Auxiliary Battery 0.969,2.281 1.51,2.542 0.542,0.26 10 false STOP 1.542,1.948 2.083,2.208 0.542,0.26 10 false 7 3.365,1.646 3.906,1.906 0.542,0.26 10 false 3 3.396,2.594 3.938,2.854 0.542,0.26 10 false 4 5.208,1.635 5.75,1.896 0.542,0.26 10 false 6 5.219,2.552 5.76,2.813 0.542,0.26 10 false 3 1.229,4.031 1.771,4.292 0.542,0.26 10 false A40 1.583,4.031 3.438,4.333 1.854,0.302 10 false Stop Light Switch Assembly 3.875,4.719 4.417,4.979 0.542,0.26 10 false N18 2.302,5.375 4.229,5.885 1.927,0.51 10 false Rear Combination Light Socket and Wire LH 3.875,6.188 4.417,6.448 0.542,0.26 10 false M14 2.292,6.896 4.24,7.469 1.948,0.573 10 false Rear Combination Light Socket and Wire RH 0.177,8.375 2.031,8.667 1.854,0.292 10 false Center Stop Light Assembly 3.896,7.688 4.438,7.948 0.542,0.26 10 false R1 3.104,1.667 3.646,1.927 0.542,0.26 10 false L 2.938,2.552 3.479,2.813 0.542,0.26 10 false ACC 2.927,3.542 3.469,3.802 0.542,0.26 10 false OUT 1.771,3.552 2.313,3.813 0.542,0.26 10 false GND 1.781,1.958 2.323,2.219 0.542,0.26 10 false B 5.458,1.635 6,1.896 0.542,0.26 10 false STP2 5.49,2.573 6.031,2.833 0.542,0.26 10 false STPO 0.552,4.906 1.313,5.125 0.76,0.219 10 false Stop Light 3.625,7.958 4.167,8.219 0.542,0.26 10 false E 5.177,3.552 5.719,3.813 0.542,0.26 10 false 33 3.354,3.552 3.896,3.813 0.542,0.26 10 false 1 1.542,3.563 2.083,3.823 0.542,0.26 10 false 2 3.958,4.927 4.5,5.188 0.542,0.26 10 false 3 3.958,4.531 4.5,4.792 0.542,0.26 10 false 2 3.958,5.99 4.5,6.25 0.542,0.26 10 false 2 3.938,7.896 4.479,8.156 0.542,0.26 10 false 1 3.948,6.396 4.49,6.656 0.542,0.26 10 false 3 3.948,7.479 4.49,7.74 0.542,0.26 10 false 2 3.635,4.646 3.844,5.031 0.208,0.385 10 false B 3.583,6.104 3.844,6.385 0.26,0.281 10 false B 5.479,3.521 6.021,3.781 0.542,0.26 10 false STP 4.865,4.344 5.406,4.604 0.542,0.26 10 false A42 4.885,4.542 6.938,5.094 2.052,0.552 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 3.635,5.01 4.177,5.271 0.542,0.26 10 false E 3.583,6.479 4.125,6.74 0.542,0.26 10 false E 3.615,7.594 4.156,7.854 0.542,0.26 10 false B 3.875,5.125 4.417,5.385 0.542,0.26 10 false N18 3.865,6.583 4.406,6.844 0.542,0.26 10 false M14 3.906,8.083 4.448,8.344 0.542,0.26 10 false R1 0.229,5.448 1.75,5.875 1.521,0.427 10 false Stop Light LED 0.219,6.896 1.781,7.344 1.563,0.448 10 false Stop Light LED 2.229,8.375 4.542,8.656 2.313,0.281 10 false Center Stop Light Cord Assembly 2.094,4.729 2.323,4.99 0.229,0.26 10 false A 2.094,5.125 2.323,5.385 0.229,0.26 10 false A 2.094,6.188 2.323,6.448 0.229,0.26 10 false B 2.083,6.583 2.313,6.844 0.229,0.26 10 false B 2.094,7.677 2.323,7.938 0.229,0.26 10 false C 2.083,8.083 2.313,8.344 0.229,0.26 10 false C 2.083,4.51 2.625,4.771 0.542,0.26 10 false 1 2.094,4.927 2.635,5.188 0.542,0.26 10 false 2 2.104,5.979 2.646,6.24 0.542,0.26 10 false 1 2.104,6.375 2.646,6.635 0.542,0.26 10 false 2 2.094,7.479 2.635,7.74 0.542,0.26 10 false 2 2.094,7.896 2.635,8.156 0.542,0.26 10 false 1 0.573,6.333 1.333,6.552 0.76,0.219 10 false Stop Light 0.573,7.854 1.333,8.073 0.76,0.219 10 false Stop Light

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the certification ECU (smart key ECU assembly) is replaced, refer to Service Bulletin.



HINT:

When C1249 is output together with C1380, inspect and repair the trouble areas indicated by C1249 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>C1249


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STP, STPO AND STP2 TERMINAL)
a.
C405855C05
0.208,0.802 0.625,1.073 0.417,0.271 1.656,1.656 2.167,0.75 2.167,0.75 2.417,0.75 true 1.333,1.667 1,0.75 1,0.75 1.25,0.75 true 1.563,2.167 2.125,3.01 2.125,3.01 2.375,3.01 true 0.198,0.188 0.823,0.583 0.625,0.396 10 false *a 0.281,0.854 0.969,1.167 0.688,0.313 10 false A42 2.479,0.667 2.885,0.875 0.406,0.208 10 false STP2 1.323,0.646 1.729,0.854 0.406,0.208 10 false STPO 2.427,2.917 2.833,3.125 0.406,0.208 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-33 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V
A42-33 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V
A42-3 (STPO) - Body ground Always 11 to 14 V
A42-6 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V
A42-6 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Result Proceed to
All terminal voltages are normal. A
Only STP2 terminal voltage abnormal. B
Only STPO terminal voltage abnormal. C
Only STP terminal voltage abnormal. D
STPO terminal and STP terminal voltage abnormal. E



A

2.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)

B

5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

C

9.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

D

10.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT LED)

E

14.CHECK STOP LIGHT SWITCH ASSEMBLY POWER SOURCE CIRCUIT
2.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)
a.

Reconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Select the Active Test on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light switch assembly (stop light control relay) Stop light switch assembly (Relay) ON/OFF Stop lights come on
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Stop Light Relay
50004 105 5

c.

According to the display on the GTS, perform the Active Test and check the operation of the stop lights.

OK:

Stop lights turn on/off in accordance with the Active Test.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
3.RECONFIRM DTC

b.

Select the Active Test on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light switch assembly (stop light control relay) Stop light switch assembly (Relay) ON/OFF Stop lights come on
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Stop Light Relay
50004 105 5

c.

According to the display on the GTS, perform the Active Test.


d.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1380 is output. A
DTC C1380 is not output. B



A

B

4.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
a.

Select the Active Test on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light switch assembly (stop light control relay) Stop light switch assembly (Relay) ON/OFF Stop lights come on
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Stop Light Relay
50004 105 5

b.
E393828C05
1.479,0.396 1.885,0.667 0.406,0.271 1.198,1.74 1.677,1.146 true 1.563,0.448 2.021,0.646 0.458,0.198 10 false A40 1.042,1.771 1.5,1.969 0.458,0.198 10 false ACC 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-4 (ACC) - Body ground Active Test is on 1.5 V or less



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the A29 hybrid vehicle control ECU assembly connector.


b.
C405855C06
0.208,0.802 0.625,1.073 0.417,0.271 1.656,1.656 2.167,0.75 2.167,0.75 2.417,0.75 true 0.198,0.188 0.823,0.583 0.625,0.396 10 false *a 0.281,0.854 0.969,1.167 0.688,0.313 10 false A42 2.479,0.667 2.885,0.875 0.406,0.208 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-6 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V
A42-6 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - SMART KEY ECU ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - SMART KEY ECU ASSEMBLY)
a.

Disconnect the M7 certification ECU (smart key ECU assembly) connector.


b.
C405855C06
0.208,0.802 0.625,1.073 0.417,0.271 1.656,1.656 2.167,0.75 2.167,0.75 2.417,0.75 true 0.198,0.188 0.823,0.583 0.625,0.396 10 false *a 0.281,0.854 0.969,1.167 0.688,0.313 10 false A42 2.479,0.667 2.885,0.875 0.406,0.208 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-6 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V
A42-6 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE SMART KEY ECU ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A40 stop light switch assembly connector.


b.
C405855C06
0.208,0.802 0.625,1.073 0.417,0.271 1.656,1.656 2.167,0.75 2.167,0.75 2.417,0.75 true 0.198,0.188 0.823,0.583 0.625,0.396 10 false *a 0.281,0.854 0.969,1.167 0.688,0.313 10 false A42 2.479,0.667 2.885,0.875 0.406,0.208 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-6 (STP2) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-6 (STP2) - A40-3 (L) Always Below 1 Ω
A42-6 (STP2) or A40-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A40 stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-3 (STPO) - A40-4 (ACC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT LED)
a.

Disconnect the A stop light LED connector.


b.
C405855C07
0.208,0.802 0.625,1.073 0.417,0.271 1.563,2.177 1.979,2.917 1.979,2.917 2.229,2.917 true 0.198,0.188 0.823,0.583 0.625,0.396 10 false *a 0.302,0.854 0.99,1.167 0.688,0.313 10 false A42 2.281,2.854 2.688,3.063 0.406,0.208 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-33 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V
A42-33 (STP) - Body ground Stop light switch assembly off (Brake pedal released) 1.5 V or less



Result:
Proceed to
OK
NG



OK

NG

11.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR COMBINATION LIGHT SOCKET AND WIRE LH)
11.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR COMBINATION LIGHT SOCKET AND WIRE LH)
a.

Disconnect the N18 rear combination light socket and wire LH connector.


b.
C405855C07
0.208,0.802 0.625,1.073 0.417,0.271 1.563,2.177 1.979,2.917 1.979,2.917 2.229,2.917 true 0.198,0.188 0.823,0.583 0.625,0.396 10 false *a 0.302,0.854 0.99,1.167 0.688,0.313 10 false A42 2.281,2.854 2.688,3.063 0.406,0.208 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-33 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V
A42-33 (STP) - Body ground Stop light switch assembly off (Brake pedal released) 1.5 V or less



Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT SOCKET AND WIRE LH

NG

12.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT LED)
12.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT LED)
a.

Disconnect the B stop light LED connector.


b.
C405855C07
0.208,0.802 0.625,1.073 0.417,0.271 1.563,2.177 1.979,2.917 1.979,2.917 2.229,2.917 true 0.198,0.188 0.823,0.583 0.625,0.396 10 false *a 0.302,0.854 0.99,1.167 0.688,0.313 10 false A42 2.281,2.854 2.688,3.063 0.406,0.208 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-33 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V
A42-33 (STP) - Body ground Stop light switch assembly off (Brake pedal released) 1.5 V or less



Result:
Proceed to
OK
NG



OK

NG

13.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR COMBINATION LIGHT SOCKET AND WIRE RH)
13.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR COMBINATION LIGHT SOCKET AND WIRE RH)
a.

Disconnect the M14 rear combination light socket and wire RH connector.


b.
C405855C07
0.208,0.802 0.625,1.073 0.417,0.271 1.563,2.177 1.979,2.917 1.979,2.917 2.229,2.917 true 0.198,0.188 0.823,0.583 0.625,0.396 10 false *a 0.302,0.854 0.99,1.167 0.688,0.313 10 false A42 2.281,2.854 2.688,3.063 0.406,0.208 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-33 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V
A42-33 (STP) - Body ground Stop light switch assembly off (Brake pedal released) 1.5 V or less



Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT SOCKET AND WIRE RH

NG

16.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - CENTER STOP LIGHT ASSEMBLY)
14.CHECK STOP LIGHT SWITCH ASSEMBLY POWER SOURCE CIRCUIT
a.

Disconnect the A40 stop light switch assembly connector.


b.
E360372C42
1.469,0.333 1.885,0.583 0.417,0.25 1.281,1.188 1,1.75 true 2.25,1.188 2.583,1.75 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.542,0.365 2,0.521 0.458,0.156 10 false A40 0.844,1.76 1.26,1.958 0.417,0.198 10 false GND 2.573,1.781 2.99,1.979 0.417,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-7 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-3 (STPO) or A40-4 (ACC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - CENTER STOP LIGHT ASSEMBLY)
a.

Disconnect the C center stop light assembly connector.


b.
C405855C07
0.208,0.802 0.625,1.073 0.417,0.271 1.563,2.177 1.979,2.917 1.979,2.917 2.229,2.917 true 0.198,0.188 0.823,0.583 0.625,0.396 10 false *a 0.302,0.854 0.99,1.167 0.688,0.313 10 false A42 2.281,2.854 2.688,3.063 0.406,0.208 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-33 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V
A42-33 (STP) - Body ground Stop light switch assembly off (Brake pedal released) 1.5 V or less



Result:
Proceed to
OK
NG



OK

NG

17.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - CENTER STOP LIGHT CORD ASSEMBLY)
17.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - CENTER STOP LIGHT CORD ASSEMBLY)
a.

Disconnect the R1 center stop light cord assembly connector.


b.
C405855C07
0.208,0.802 0.625,1.073 0.417,0.271 1.563,2.177 1.979,2.917 1.979,2.917 2.229,2.917 true 0.198,0.188 0.823,0.583 0.625,0.396 10 false *a 0.302,0.854 0.99,1.167 0.688,0.313 10 false A42 2.281,2.854 2.688,3.063 0.406,0.208 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-33 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V
A42-33 (STP) - Body ground Stop light switch assembly off (Brake pedal released) 1.5 V or less



Result:
Proceed to
OK
NG



OK

REPLACE CENTER STOP LIGHT CORD ASSEMBLY

NG

18.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
18.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.
C405855C07
0.208,0.802 0.625,1.073 0.417,0.271 1.563,2.177 1.979,2.917 1.979,2.917 2.229,2.917 true 0.198,0.188 0.823,0.583 0.625,0.396 10 false *a 0.302,0.854 0.99,1.167 0.688,0.313 10 false A42 2.281,2.854 2.688,3.063 0.406,0.208 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Disconnect the A40 stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-33 (STP) - Body ground Always 1.5 V or less



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-1 (OUT) - A42-33 (STP) Always Below 1 Ω
A40-1 (OUT) or A42-33 (STP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR