Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0375511 PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model) J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)  Image from Camera for Panoramic View Monitor is Abnormal  


DESCRIPTION

The display signal from each television camera is transmitted to the radio and display receiver assembly via the parking assist ECU.

WIRING DIAGRAM

E407122E01
3.125,7.229 3.74,7.427 0.615,0.198 10 false CGND 3.125,7.677 3.74,7.875 0.615,0.198 10 false SGND 2.469,5.938 3.083,6.135 0.615,0.198 10 false SGND 3.115,4.865 3.729,5.063 0.615,0.198 10 false SGND 3.083,2.063 3.698,2.26 0.615,0.198 10 false SGND 0.073,2.938 1.792,3.302 1.719,0.365 10 false Radio and Display Receiver Assembly 0.083,6.521 1.615,7.031 1.531,0.51 10 false Front Television Camera Assembly 4.833,2.469 7.156,2.719 2.323,0.25 10 false Outer Rear View Mirror Assembly RH 5.552,1.865 7.021,2.271 1.469,0.406 10 false Side Television Camera Assembly RH 4.865,5.354 7.156,5.625 2.292,0.271 10 false Outer Rear View Mirror Assembly LH 5.531,4.677 7,5.01 1.469,0.333 10 false Side Television Camera Assembly LH 5.896,7.969 7.063,8.333 1.167,0.365 10 false Television Camera Assembly 2.354,8.135 3.708,8.427 1.354,0.292 10 false Parking Assist ECU 3.104,0.365 3.719,0.563 0.615,0.198 10 false RCB+ 3.104,0.781 3.719,0.979 0.615,0.198 10 false RCV+ 3.125,1.219 3.74,1.417 0.615,0.198 10 false RCV- 3.083,1.615 3.698,1.813 0.615,0.198 10 false RGND 2.469,0.427 3.083,0.625 0.615,0.198 10 false NS+ 2.458,1.073 3.073,1.271 0.615,0.198 10 false NS- 2.469,1.719 3.083,1.917 0.615,0.198 10 false NSG 0.979,0.427 1.594,0.625 0.615,0.198 10 false V+ 1.031,1.073 1.646,1.271 0.615,0.198 10 false V- 0.063,2.771 0.677,2.969 0.615,0.198 10 false G2 1.313,0.302 1.573,0.5 0.26,0.198 10 false 28 1.302,0.938 1.531,1.135 0.229,0.198 10 false 29 2.208,0.313 2.365,0.51 0.156,0.198 10 false 7 2.146,0.958 2.375,1.156 0.229,0.198 10 false 24 2.208,1.594 2.365,1.792 0.156,0.198 10 false 8 2.354,7.969 2.969,8.167 0.615,0.198 10 false N24 3.635,7.552 4.01,7.729 0.375,0.177 10 false 31 3.615,7.135 3.99,7.313 0.375,0.177 10 false 32 3.219,6.833 3.833,7.031 0.615,0.198 10 false CV- 3.208,6.417 3.823,6.615 0.615,0.198 10 false CV+ 3.198,5.969 3.813,6.167 0.615,0.198 10 false CB+ 6.375,5.979 6.99,6.177 0.615,0.198 10 false CB+ 6.385,6.385 7,6.583 0.615,0.198 10 false CV+ 6.396,6.802 7.01,7 0.615,0.198 10 false CV- 6.375,7.24 6.99,7.438 0.615,0.198 10 false CGND 3.615,6.719 3.99,6.896 0.375,0.177 10 false 30 3.615,5.875 3.99,6.052 0.375,0.177 10 false 33 6.156,5.885 6.531,6.063 0.375,0.177 10 false 6 6.156,6.271 6.531,6.448 0.375,0.177 10 false 3 6.167,6.708 6.542,6.885 0.375,0.177 10 false 2 6.156,7.146 6.531,7.323 0.375,0.177 10 false 5 5.906,7.771 6.521,7.969 0.615,0.198 10 false R15 0.771,4.063 1.146,4.24 0.375,0.177 10 false 6 0.781,4.458 1.156,4.635 0.375,0.177 10 false 3 0.771,4.906 1.146,5.083 0.375,0.177 10 false 2 0.771,5.344 1.146,5.521 0.375,0.177 10 false 5 0.083,6.354 0.698,6.552 0.615,0.198 10 false B12 2.469,5.458 3.083,5.656 0.615,0.198 10 false BGND 0.302,5.448 0.917,5.646 0.615,0.198 10 false BGND 2.5,4.99 3.115,5.188 0.615,0.198 10 false BCV- 2.5,4.552 3.115,4.75 0.615,0.198 10 false BCV+ 2.5,4.156 3.115,4.354 0.615,0.198 10 false BCB+ 0.281,4.177 0.896,4.375 0.615,0.198 10 false BCB+ 0.271,4.563 0.885,4.76 0.615,0.198 10 false BCV+ 0.302,4.979 0.917,5.177 0.615,0.198 10 false BCV- 2.156,5.844 2.479,6.021 0.323,0.177 10 false 14 2.167,5.354 2.49,5.531 0.323,0.177 10 false 37 2.156,4.896 2.479,5.073 0.323,0.177 10 false 13 2.156,4.479 2.479,4.656 0.323,0.177 10 false 36 2.156,4.052 2.479,4.229 0.323,0.177 10 false 15 3.635,0.281 3.958,0.458 0.323,0.177 10 false 40 3.635,0.698 3.958,0.875 0.323,0.177 10 false 38 3.625,1.115 3.948,1.292 0.323,0.177 10 false 16 3.625,1.531 3.948,1.708 0.323,0.177 10 false 17 3.615,1.969 3.938,2.146 0.323,0.177 10 false 39 5.302,0.271 5.917,0.469 0.615,0.198 10 false RCB+ 5.313,0.677 5.927,0.875 0.615,0.198 10 false RCV+ 5.313,1.094 5.927,1.292 0.615,0.198 10 false RCV- 5.292,1.51 5.906,1.708 0.615,0.198 10 false RGND 4.854,2.302 5.198,2.542 0.344,0.24 10 false I13 5.083,0.26 5.438,0.573 0.354,0.313 10 false 3 5.094,0.698 5.448,1.01 0.354,0.313 10 false 4 5.021,1.083 5.375,1.396 0.354,0.313 10 false 12 5.021,1.49 5.375,1.802 0.354,0.313 10 false 11 4.875,5.156 5.219,5.396 0.344,0.24 10 false J13 3.135,4.427 3.75,4.625 0.615,0.198 10 false LGND 3.135,4.031 3.75,4.229 0.615,0.198 10 false LCV- 3.146,3.594 3.76,3.792 0.615,0.198 10 false LCV+ 3.146,3.177 3.76,3.375 0.615,0.198 10 false LCB+ 3.625,3.083 3.948,3.26 0.323,0.177 10 false 12 3.625,3.51 3.948,3.688 0.323,0.177 10 false 10 3.635,3.917 3.958,4.094 0.323,0.177 10 false 34 3.625,4.344 3.948,4.521 0.323,0.177 10 false 35 3.625,4.771 3.948,4.948 0.323,0.177 10 false 11 5.333,3.063 5.948,3.26 0.615,0.198 10 false LCB+ 5.333,3.479 5.948,3.677 0.615,0.198 10 false LCV+ 5.344,3.885 5.958,4.083 0.615,0.198 10 false LCV- 5.333,4.323 5.948,4.521 0.615,0.198 10 false LGND 5.063,3.063 5.417,3.375 0.354,0.313 10 false 3 5.073,3.469 5.427,3.781 0.354,0.313 10 false 4 5.01,3.885 5.365,4.198 0.354,0.313 10 false 12 5,4.302 5.354,4.615 0.354,0.313 10 false 11 1.625,1.646 1.781,1.844 0.156,0.198 10 false * 4.542,1.99 4.698,2.188 0.156,0.198 10 false * 4.542,4.792 4.698,4.99 0.156,0.198 10 false * 1.302,5.854 1.458,6.052 0.156,0.198 10 false * 5.063,7.594 5.219,7.792 0.156,0.198 10 false * 0.156,8.5 1.052,8.75 0.896,0.25 10 false *: Shielded 6.24,0.24 6.625,0.458 0.385,0.219 10 false 1 5.563,1.729 5.948,1.948 0.385,0.219 10 false B 6.26,0.677 6.646,0.896 0.385,0.219 10 false 3 6.26,1.115 6.646,1.333 0.385,0.219 10 false 7 6.26,1.521 6.646,1.74 0.385,0.219 10 false 5 6.26,4.302 6.646,4.521 0.385,0.219 10 false 5 6.26,3.906 6.646,4.125 0.385,0.219 10 false 7 6.25,3.448 6.635,3.667 0.385,0.219 10 false 3 6.25,3.042 6.635,3.26 0.385,0.219 10 false 1 5.552,4.552 5.938,4.771 0.385,0.219 10 false A 3.615,6.302 3.99,6.479 0.375,0.177 10 false 29 6.458,0.365 6.875,0.552 0.417,0.188 10 false SCB+ 6.469,0.781 6.885,0.969 0.417,0.188 10 false SCV+ 6.479,1.219 6.896,1.406 0.417,0.188 10 false SCV- 6.479,1.615 6.896,1.802 0.417,0.188 10 false SGND 6.531,3.146 6.948,3.333 0.417,0.188 10 false SCB+ 6.51,3.615 6.927,3.802 0.417,0.188 10 false SCV+ 6.5,4.052 6.917,4.24 0.417,0.188 10 false SCV- 6.49,4.417 6.906,4.604 0.417,0.188 10 false SGND 2.208,2.25 2.365,2.448 0.156,0.198 10 false 6 2.458,2.365 3.073,2.563 0.615,0.198 10 false RSW+ 0.802,2.344 1.417,2.542 0.615,0.198 10 false CSW+ 1.302,2.24 1.531,2.438 0.229,0.198 10 false 18

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the parking assist ECU after the battery terminal has been disconnected, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>CALIBRATION

·

The following malfunctions may occur if a radio and display receiver assembly from another vehicle is installed to this vehicle. Therefore, when replacing the radio and display receiver assembly, be sure to replace it with a new one.

-

Communication malfunction DTC is output

-

Does not operate normally




HINT:
Images may be unclear even in normal conditions if:
·

Electrical devices are used in the cabin (noise may occur in the image).

·

The camera lens is frosted over (the image immediately after turning the engine switch on (IG) may be blurred or darker than normal).

·

The camera lens is dirty with snow, mud, etc.

·

A strong beam of light, such as a sunbeam or headlight, hits the camera.

·

It is too dark around the camera (at night, etc.).

·

The ambient temperature around the camera is either too high or too low.

·

The vehicle is tilted at a steep angle.

·

The television camera assembly lens is scratched.

·

The television camera assembly lens has drops of water on it or the humidity is high.

·

When the camera is used under fluorescent lights, sodium lights, or mercury lights, etc., the lights and the illuminated area may appear to flicker.



PROCEDURE

1.CHECK PANORAMIC VIEW MONITOR SYSTEM
a.

Check if the same malfunction occurs when the panoramic view monitor screen is displayed.


Result:
Result Proceed to
Rear view screen is not displayed. A
Front view screen is not displayed. B
Side monitor screen (LH side) is not displayed. C
Side monitor screen (RH side) is not displayed. D
Panoramic view monitor screen is not displayed. E



A

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - TELEVISION CAMERA ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY)

C

8.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH)

D

13.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH)

E

18.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the N24 parking assist ECU connector.


b.

Disconnect the R15 television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-33 (CB+) - R15-6 (CB+) Always Below 1 Ω
N24-29 (CV+) - R15-3 (CV+) Always Below 1 Ω
N24-30 (CV-) - R15-2 (CV-) Always Below 1 Ω
N24-32 (CGND) - R15-5 (CGND) Always Below 1 Ω
N24-31 (SGND) - Body ground Always 10 kΩ or higher
N24-33 (CB+) or R15-6 (CB+) - Body ground Always 10 kΩ or higher
N24-29 (CV+) or R15-3 (CV+) - Body ground Always 10 kΩ or higher
N24-30 (CV-) or R15-2 (CV-) - Body ground Always 10 kΩ or higher
N24-32 (CGND) or R15-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK PARKING ASSIST ECU (CB+, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK PARKING ASSIST ECU (CB+, CGND)
a.
E407111C02
1.417,0.25 1.917,0.5 0.5,0.25 1.438,1.146 1.208,1.906 1.208,1.906 0.958,1.906 true 1.51,1.156 1.979,1.948 1.979,1.948 2.229,1.948 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 0.646,1.823 1.115,2.021 0.469,0.198 10 false CB+ 1.542,0.292 2.042,0.448 0.5,0.156 10 false N24 2.271,1.865 2.833,2.052 0.563,0.188 10 false CGND
*a Component with harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-32 (CGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N24-33 (CB+) - R24-32 (CGND) Engine switch on (IG) 5.5 to 7.05 V
N24-33 (CB+) - R24-32 (CGND) Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK TELEVISION CAMERA ASSEMBLY (CV+, CGND)

NG

4.CHECK TELEVISION CAMERA ASSEMBLY (CV+, CGND)
a.

Remove the parking assist ECU with the connector still connected.


b.

Using an oscilloscope, check the waveform of the television camera assembly.

HINT:

A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


E245725C76
0.75,0.292 1.25,0.542 0.5,0.25 1.313,1.354 1.167,1.354 1.167,1.354 1.052,1.104 true 4.302,2.052 4.104,1.552 true 6.333,2.052 6.083,1.406 true 5.802,2.031 5.969,1.458 true 3.813,2.031 3.969,1.594 true 0.583,2.063 0.75,2.063 0.75,2.063 0.875,1.094 true 1.396,1.271 1.75,1.469 0.354,0.198 10 false CV+ 0.104,1.99 0.583,2.167 0.479,0.177 10 false CGND 3.365,1.188 3.844,1.365 0.479,0.177 10 false GND 5.271,1.188 5.75,1.365 0.479,0.177 10 false GND 0.083,0.063 0.563,0.24 0.479,0.177 10 false *a 3.469,0.083 3.948,0.26 0.479,0.177 10 false *b 5.417,0.073 5.896,0.25 0.479,0.177 10 false *c 6.302,2.094 6.781,2.271 0.479,0.177 10 false *e 4.271,2.083 4.75,2.26 0.479,0.177 10 false *e 5.688,2.094 6.167,2.271 0.479,0.177 10 false *d 3.74,2.083 4.219,2.26 0.479,0.177 10 false *d 0.875,0.333 1.354,0.51 0.479,0.177 10 false N24
*a Component with harness connected
(Parking Assist ECU)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen) *d Synchronization Signal
*e Video Waveform - -


HINT:
·

The video waveform changes according to the image sent by the television camera assembly.

·

The video waveform is constantly output when the engine switch is on (ACC).



Measurement Condition
Item Content
Terminal No. (Symbol) N24-29 (CV+) - N24-32 (CGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Engine switch on (IG), panoramic view monitor switch on

OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the N24 parking assist ECU connector.


b.

Disconnect the B12 front television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-15 (BCB+) - B12-6 (BCB+) Always Below 1 Ω
N24-36 (BCV+) - B12-3 (BCV+) Always Below 1 Ω
N24-13 (BCV-) - B12-2 (BCV-) Always Below 1 Ω
N24-37 (BGND) - B12-5 (BGND) Always Below 1 Ω
N24-14 (SGND) - Body ground Always 10 kΩ or higher
N24-15 (BCB+) or B12-6 (BCB+) - Body ground Always 10 kΩ or higher
N24-36 (BCV+) or B12-3 (BCV+) - Body ground Always 10 kΩ or higher
N24-13 (BCV-) or B12-2 (BCV-) - Body ground Always 10 kΩ or higher
N24-37 (BGND) or B12-5 (BGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK PARKING ASSIST ECU (BCB+, BGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK PARKING ASSIST ECU (BCB+, BGND)
a.
E407111C03
1.417,0.25 1.917,0.5 0.5,0.25 1.073,0.979 0.917,0.365 0.917,0.365 0.667,0.365 true 1.073,1.167 0.865,1.906 0.865,1.906 0.615,1.906 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 0.26,0.281 0.729,0.479 0.469,0.198 10 false BCB+ 1.542,0.292 2.042,0.448 0.5,0.156 10 false N24 0.188,1.823 0.75,2.01 0.563,0.188 10 false BGND
*a Component with harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-37 (BGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N24-15 (BCB+) - N24-37 (BGND) Engine switch on (IG) 5.5 to 7.05 V
N24-15 (BCB+) - N24-37 (BGND) Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

7.CHECK FRONT TELEVISION CAMERA ASSEMBLY

NG

7.CHECK FRONT TELEVISION CAMERA ASSEMBLY
a.

Remove the parking assist ECU with the connector still connected.


b.

Using an oscilloscope, check the waveform of the front television camera assembly.

HINT:

A waterproof connector is used for the front television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


E245725C87
0.75,0.292 1.25,0.542 0.5,0.25 1,1.354 0.771,1.354 0.771,1.354 0.656,1.104 true 4.302,2.052 4.104,1.552 true 6.333,2.052 6.083,1.406 true 5.802,2.031 5.969,1.458 true 3.813,2.031 3.969,1.594 true 0.938,2.26 0.688,2.26 0.688,2.26 0.521,1.115 true 1.063,1.271 1.656,1.573 0.594,0.302 10 false BCV+ 0.99,2.167 1.469,2.344 0.479,0.177 10 false BGND 3.365,1.188 3.844,1.365 0.479,0.177 10 false GND 5.271,1.188 5.75,1.365 0.479,0.177 10 false GND 0.083,0.063 0.563,0.24 0.479,0.177 10 false *a 3.469,0.083 3.948,0.26 0.479,0.177 10 false *b 5.417,0.073 5.896,0.25 0.479,0.177 10 false *c 6.302,2.094 6.781,2.271 0.479,0.177 10 false *e 4.271,2.083 4.75,2.26 0.479,0.177 10 false *e 5.688,2.094 6.167,2.271 0.479,0.177 10 false *d 3.74,2.083 4.219,2.26 0.479,0.177 10 false *d 0.865,0.333 1.344,0.51 0.479,0.177 10 false N24
*a Component with harness connected
(Parking Assist ECU)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen) *d Synchronization Signal
*e Video Waveform - -


HINT:
·

The video waveform changes according to the image sent by the front television camera assembly.

·

The video waveform is constantly output when the engine switch is on (ACC).



Measurement Condition
Item Content
Terminal No. (Symbol) N24-36 (BCV+) - N24-37 (BGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Engine switch on (IG), panoramic view monitor switch on

OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG

8.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH)
a.

Disconnect the N24 parking assist ECU connector.


b.

Disconnect the J13 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-12 (LCB+) - J13-3 (LCB+) Always Below 1 Ω
N24-10 (LCV+) - J13-4 (LCV+) Always Below 1 Ω
N24-34 (LCV-) - J13-12 (LCV-) Always Below 1 Ω
N24-35 (LGND) - J13-11 (LGND) Always Below 1 Ω
N24-12 (LCB+) or J13-3 (LCB+) - Body ground Always 10 kΩ or higher
N24-10 (LCV+) or J13-4 (LCV+) - Body ground Always 10 kΩ or higher
N24-34 (LCV-) or J13-12 (LCV-) - Body ground Always 10 kΩ or higher
N24-35 (LGND) or J13-11 (LGND) - Body ground Always 10 kΩ or higher
N24-11 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK PARKING ASSIST ECU (LCB+, LGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK PARKING ASSIST ECU (LCB+, LGND)
a.
E407111C05
1.417,0.25 1.917,0.5 0.5,0.25 0.667,1.917 1,1.917 1,1.917 1.302,1.135 true 0.917,0.667 1.167,0.667 1.167,0.667 1.25,0.958 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 0.542,0.583 1.031,0.75 0.49,0.167 10 false LCB+ 0.25,1.833 0.813,1.99 0.563,0.156 10 false LGND 1.542,0.281 2.042,0.438 0.5,0.156 10 false N24
*a Component with harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-35 (LGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N24-12 (LCB+) - N24-35 (LGND) Engine switch on (IG) 5.5 to 7.05 V
N24-12 (LCB+) - N24-35 (LGND) Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

10.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH

NG

10.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH
a.

Remove the parking assist ECU with the connector still connected.


b.

Using an oscilloscope, check the waveform of the side television camera assembly LH.

HINT:

A waterproof connector is used for the side television camera assembly LH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


E245725C90
0.75,0.292 1.25,0.542 0.5,0.25 0.708,1.104 0.646,2.094 0.646,2.094 0.49,2.094 true 1.104,1.333 0.958,1.333 0.958,1.333 0.802,1.021 true 4.302,2.052 4.104,1.552 true 6.333,2.052 6.083,1.406 true 5.802,2.031 5.969,1.458 true 3.813,2.031 3.969,1.594 true 1.188,1.26 1.917,1.51 0.729,0.25 10 false LCV+ 0.073,2.021 0.552,2.198 0.479,0.177 10 false LGND 3.365,1.156 3.844,1.333 0.479,0.177 10 false GND 5.26,1.167 5.74,1.344 0.479,0.177 10 false GND 0.083,0.063 0.563,0.24 0.479,0.177 10 false *a 3.469,0.083 3.948,0.26 0.479,0.177 10 false *b 5.417,0.073 5.896,0.25 0.479,0.177 10 false *c 6.302,2.094 6.781,2.271 0.479,0.177 10 false *e 4.271,2.083 4.75,2.26 0.479,0.177 10 false *e 5.688,2.094 6.167,2.271 0.479,0.177 10 false *d 3.74,2.083 4.219,2.26 0.479,0.177 10 false *d 0.875,0.323 1.354,0.5 0.479,0.177 10 false N24
*a Component with harness connected
(Parking Assist ECU)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen) *d Synchronization Signal
*e Video Waveform - -


HINT:
·

The video waveform changes according to the image sent by the side television camera assembly LH.

·

The video waveform is constantly output when the engine switch is on (ACC).



Measurement Condition
Item Content
Tester Connection N24-10 (LCV+) - N24-35 (LGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Engine switch on (IG), panoramic view monitor switch on

OK:

Waveform is similar to that shown in illustration.



Result:
Proceed to
OK
NG



OK

NG

11.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
11.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.
E407112C02
0.646,0.833 1.146,1.083 0.5,0.25 0.323,2.281 0.823,2.531 0.5,0.25 0.99,0.375 1.24,0.375 1.24,0.375 1.427,0.76 true 2.406,0.365 2.156,0.365 2.156,0.365 1.979,0.75 true 1,1.427 1.25,1.427 1.25,1.427 1.427,1.104 true 2.438,1.427 2.188,1.427 2.188,1.427 2.01,1.073 true 1.146,1.813 1.396,1.813 1.396,1.813 1.479,2.427 true 2,1.813 1.75,1.813 1.75,1.813 1.635,2.438 true 1.99,3.167 1.74,3.167 1.74,3.167 1.656,2.677 true 1.146,3.156 1.396,3.156 1.396,3.156 1.521,2.688 true 0.74,1.719 1.354,1.917 0.615,0.198 10 false LCB+ 2.458,0.281 3.073,0.479 0.615,0.198 10 false SCB+ 0.573,0.302 1.188,0.5 0.615,0.198 10 false SCV+ 0.604,1.333 1.219,1.531 0.615,0.198 10 false SCV- 2.49,1.333 3.104,1.531 0.615,0.198 10 false SGND 2.052,1.719 2.667,1.917 0.615,0.198 10 false LCV+ 0.74,3.083 1.354,3.281 0.615,0.198 10 false LGND 2.042,3.083 2.656,3.281 0.615,0.198 10 false LCV- 0.833,0.875 1.448,1.073 0.615,0.198 10 false A 0.458,2.323 1.073,2.521 0.615,0.198 10 false J13 0.052,0.052 0.667,0.25 0.615,0.198 10 false *a 0.063,1.625 0.677,1.823 0.615,0.198 10 false *b
*a Front view of wire harness connector
(to Side Television Camera Assembly LH)
*b Front view of wire harness connector
(to Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


b.

Disconnect the side television camera assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (SCB+) - J13-3 (LCB+) Always Below 1 Ω
A-3 (SCV+) - J13-4 (LCV+) Always Below 1 Ω
A-7 (SCV-) - J13-12 (LCV-) Always Below 1 Ω
A-5 (SGND) - J13-11 (LGND) Always Below 1 Ω
A-1 (SCB+) or J13-3 (LCB+) - Body ground Always 10 kΩ or higher
A-3 (SCV+) or J13-4 (LCV+) - Body ground Always 10 kΩ or higher
A-7 (SCV-) or J13-12 (LCV-) - Body ground Always 10 kΩ or higher
A-5 (SGND) or J13-11 (LGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

12.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH
a.

Replace the side television camera assembly LH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL


b.

Check if the same malfunction reoccurs when the side monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal)



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY LH IS DEFECTIVE)

NG

13.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH)
a.

Disconnect the N24 parking assist ECU connector.


b.

Disconnect the I13 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-40 (RCB+) - I13-3 (RCB+) Always Below 1 Ω
N24-38 (RCV+) - I13-4 (RCV+) Always Below 1 Ω
N24-16 (RCV-) - I13-12 (RCV-) Always Below 1 Ω
N24-17 (RGND) - I13-11 (RGND) Always Below 1 Ω
N24-40 (RCB+) or I13-3 (RCB+) - Body ground Always 10 kΩ or higher
N24-38 (RCV+) or I13-4 (RCV+) - Body ground Always 10 kΩ or higher
N24-16 (RCV-) or I13-12 (RCV-) - Body ground Always 10 kΩ or higher
N24-17 (RGND) or I13-11 (RGND) - Body ground Always 10 kΩ or higher
N24-39 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK PARKING ASSIST ECU (RCB+, RGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK PARKING ASSIST ECU (RCB+, RGND)
a.
E407111C04
1.417,0.25 1.917,0.5 0.5,0.25 0.698,0.677 0.875,0.677 0.875,0.677 0.938,1 true 0.854,1.146 0.719,1.75 0.719,1.75 0.542,1.75 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 0.146,1.656 0.615,1.854 0.469,0.198 10 false RCB+ 1.542,0.292 2.042,0.448 0.5,0.156 10 false N24 0.281,0.594 0.844,0.781 0.563,0.188 10 false RGND
*a Component with harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-17 (RGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N24-40 (RCB+) - N24-17 (RGND) Engine switch on (IG) 5.5 to 7.05 V
N24-40 (RCB+) - N24-17 (RGND) Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

15.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH

NG

15.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH
a.

Remove the parking assist ECU with the connector still connected.


b.

Using an oscilloscope, check the waveform of the side television camera assembly RH.

HINT:

A waterproof connector is used for the side television camera assembly RH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


E245725C88
0.75,0.302 1.25,0.552 0.5,0.25 0.646,0.74 0.5,0.74 0.5,0.74 0.406,0.99 true 4.302,2.052 4.104,1.552 true 6.333,2.052 6.083,1.406 true 5.802,2.031 5.969,1.458 true 3.813,2.031 3.969,1.594 true 0.74,2.177 0.594,2.177 0.594,2.177 0.469,1.104 true 0.875,2.094 1.344,2.333 0.469,0.24 10 false RCV+ 0.688,0.667 1.167,0.844 0.479,0.177 10 false RGND 3.365,1.156 3.844,1.333 0.479,0.177 10 false GND 5.26,1.167 5.74,1.344 0.479,0.177 10 false GND 0.083,0.063 0.563,0.24 0.479,0.177 10 false *a 3.469,0.083 3.948,0.26 0.479,0.177 10 false *b 5.417,0.073 5.896,0.25 0.479,0.177 10 false *c 6.302,2.094 6.781,2.271 0.479,0.177 10 false *e 4.271,2.083 4.75,2.26 0.479,0.177 10 false *e 5.688,2.094 6.167,2.271 0.479,0.177 10 false *d 3.74,2.083 4.219,2.26 0.479,0.177 10 false *d 0.875,0.333 1.354,0.51 0.479,0.177 10 false N24
*a Component with harness connected
(Parking Assist ECU)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen) *d Synchronization Signal
*e Video Waveform - -


HINT:
·

The video waveform changes according to the image sent by the side television camera assembly RH.

·

The video waveform is constantly output when the engine switch is on (ACC).



Measurement Condition
Item Content
Tester Connection N24-38 (RCV+) - N24-17 (RGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Engine switch on (IG), panoramic view monitor switch on

OK:

Waveform is similar to that shown in illustration.



Result:
Proceed to
OK
NG



OK

NG

16.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
16.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
a.
E407112C01
0.646,0.833 1.146,1.083 0.5,0.25 0.323,2.281 0.823,2.531 0.5,0.25 0.99,0.375 1.24,0.375 1.24,0.375 1.427,0.76 true 2.406,0.365 2.156,0.365 2.156,0.365 1.979,0.75 true 1,1.427 1.25,1.427 1.25,1.427 1.427,1.104 true 2.438,1.427 2.188,1.427 2.188,1.427 2.01,1.073 true 1.146,1.813 1.396,1.813 1.396,1.813 1.479,2.427 true 2,1.813 1.75,1.813 1.75,1.813 1.635,2.438 true 1.99,3.167 1.74,3.167 1.74,3.167 1.656,2.677 true 1.146,3.156 1.396,3.156 1.396,3.156 1.521,2.688 true 0.74,1.719 1.354,1.917 0.615,0.198 10 false RCB+ 2.458,0.281 3.073,0.479 0.615,0.198 10 false SCB+ 0.573,0.302 1.188,0.5 0.615,0.198 10 false SCV+ 0.604,1.333 1.219,1.531 0.615,0.198 10 false SCV- 2.49,1.333 3.104,1.531 0.615,0.198 10 false SGND 2.052,1.719 2.667,1.917 0.615,0.198 10 false RCV+ 0.74,3.083 1.354,3.281 0.615,0.198 10 false RGND 2.042,3.083 2.656,3.281 0.615,0.198 10 false RCV- 0.833,0.875 1.448,1.073 0.615,0.198 10 false B 0.458,2.323 1.073,2.521 0.615,0.198 10 false I13 0.052,0.052 0.667,0.25 0.615,0.198 10 false *a 0.063,1.625 0.677,1.823 0.615,0.198 10 false *b
*a Front view of wire harness connector
(to Side Television Camera Assembly RH)
*b Front view of wire harness connector
(to Outer Rear View Mirror Assembly RH)


Disconnect the side television camera assembly RH connector.


b.

Disconnect the outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 (SCB+) - I13-3 (RCB+) Always Below 1 Ω
B-3 (SCV+) - I13-4 (RCV+) Always Below 1 Ω
B-7 (SCV-) - I13-12 (RCV-) Always Below 1 Ω
B-5 (SGND) - I13-11 (RGND) Always Below 1 Ω
B-1 (SCB+) or I13-3 (RCB+) - Body ground Always 10 kΩ or higher
B-3 (SCV+) or I13-4 (RCV+) - Body ground Always 10 kΩ or higher
B-7 (SCV-) or I13-12 (RCV-) - Body ground Always 10 kΩ or higher
B-5 (SGND) or I13-11 (RGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

17.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH
a.

Replace the side television camera assembly RH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL


b.

Check if the same malfunction reoccurs when the side monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal)



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY RH IS DEFECTIVE)

NG

18.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the N24 parking assist ECU connector.


b.

Disconnect the G2 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N24-7 (NS+) - G2-28 (V+) Always Below 1 Ω
N24-24 (NS-) - G2-29 (V-) Always Below 1 Ω
N24-6 (RSW+) - G2-18 (CSW+) Always Below 1 Ω
N24-7 (NS+) or G2-28 (V+) - Body ground Always 10 kΩ or higher
N24-24 (NS-) or G2-29 (V-) - Body ground Always 10 kΩ or higher
N24-8 (NSG) - Body ground Always 10 kΩ or higher
N24-6 (RSW+) or G2-18 (CSW+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Replace the radio and display receiver assembly with a new.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.

Check if the same malfunction reoccurs when the panoramic view monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal).



Result:
Proceed to
OK
NG



OK

END (RADIO AND DISPLAY RECEIVER ASSEMBLY WAS DEFECTIVE)

NG