Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM (for Gasoline Model)
RM3620E _59 Vehicle Exterior _076335 DOOR / HATCH _0376805 POWER BACK DOOR SYSTEM(for Gasoline Model) J

DOOR / HATCH  POWER BACK DOOR SYSTEM(for Gasoline Model)  Power Back Door does not Operate Using Cabin Switch  


DESCRIPTION

The power back door control switch signal is sent to the multiplex network door ECU.

If the power back door does not operate using the power back door control switch, a power back door control switch circuit malfunction is a possible cause.

WIRING DIAGRAM

E270968E09
1.344,1.427 1.802,1.625 0.458,0.198 10 false G11 1.344,1.625 2.917,1.979 1.573,0.354 10 false Power Back Door Control Switch 0.781,2.354 4.448,2.552 3.667,0.198 10 false : CAN Communication Line 5.063,1.979 6.896,2.344 1.833,0.365 10 false Multiplex Network Door ECU 3.125,1.917 3.583,2.115 0.458,0.198 10 false G45 3.115,2.094 4.76,2.448 1.646,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 3.646,1.052 4.323,1.271 0.677,0.219 10 false PBDS 3.458,0.938 3.917,1.135 0.458,0.198 10 false 4 1.229,0.948 1.688,1.146 0.458,0.198 10 false 2 2.938,0.927 3.396,1.125 0.458,0.198 10 false 5 1.542,0.948 2,1.146 0.458,0.198 10 false MSE 2.396,0.948 2.854,1.146 0.458,0.198 10 false MSW

CAUTION / NOTICE / HINT

NOTICE:
·

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>INITIALIZATION

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

*: w/ Door Control Battery




PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>DATA LIST / ACTIVE TEST

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back Door Open SW Power back door control switch signal ON or OFF ON: Power back door control switch on
OFF: Power back door control switch off
-
Body Electrical > Main Body > Data List
Tester Display
Back Door Open SW
50003 123 95
OK:

The power back door control switch functions as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

2.INSPECT POWER BACK DOOR CONTROL SWITCH
2.INSPECT POWER BACK DOOR CONTROL SWITCH
a.

Remove the power back door control switch.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR CONTROL SWITCH>REMOVAL


b.

Inspect the power back door control switch.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR CONTROL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR CONTROL SWITCH - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)

NG

REPLACE POWER BACK DOOR CONTROL SWITCH

3.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR CONTROL SWITCH - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

Disconnect the G11 power back door control switch connector.


b.

Disconnect the G45 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G11-5 (MSW) - G45-4 (PBDS) Always Below 1 Ω
G11-2 (MSE) - Body ground Always Below 1 Ω
G11-5 (MSW) or G45-4 (PBDS) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR