Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
When installing the main body ECU (multiplex network body ECU), always replace it with a new one.
89221
1.INSTALL MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (except Manual Transaxle)
Hold the main body ECU (multiplex network body ECU) with your dominant hand.
| *a | Connector |
Do not touch the connector.
Make sure foreign matter does not enter the terminals.
| *a | Fitting Surface |
Hold the instrument panel junction block assembly with your other hand.
Make sure there is no foreign matter in the fitting surface.
| *a | 20° or more |
|
Install in this Direction |
|
Housing Sidewall |
Set the guide of the main body ECU (multiplex network body ECU) against the housing sidewall.
Make sure the angle between the instrument panel junction block assembly and the main body ECU (multiplex network body ECU) is 20° or more.
|
Install in this Direction |
|
Housing Sidewall |
Slide the guide of the main body ECU (multiplex network body ECU) along the housing sidewall in the direction indicated by the arrow.
|
Install in this Direction |
|
Side A |
Slide it until it contacts side A.
|
Install in this Direction |
Contact side A.
Do not contact side A with the main body ECU (multiplex network body ECU) too hard.
| *a | Center of Rotation (Contacts Surface A) |
|
Rotate in this Direction |
| *a | Center of Rotation (Contacts Surface A) |
|
Rotate in this Direction |
While pressing the main body ECU (multiplex network body ECU) against side A (center of rotation) of the instrument panel junction block assembly, rotate it until it enters the lock of the instrument panel junction block assembly.
The center of rotation is the one that contacts surface A.
Rotate it until it enters the lock of the instrument panel junction block assembly.
| *a | Before Locking | *b | Main Body ECU (Multiplex Network Body ECU) Lock |
| *c | Instrument Panel Junction Block Assembly Lock | - | - |
|
Install in this Direction |
|
Pressing Area |
Press the pressing area of the main body ECU (multiplex network body ECU).
Press it in one of the following ways.
| *a | Press the 2 sides of the main body ECU (multiplex network body ECU) with both hands. | *b | Press the center of the main body ECU (multiplex network body ECU) with one hand. |
|
Place fingers or the palm of your hand here | - | - |
Do not hit on or put your weight on the main body ECU (multiplex network body ECU) when engaging the main body ECU (multiplex network body ECU).
Check the engagement of the main body ECU (multiplex network body ECU) and the instrument panel junction block assembly by the locking sound.
| *a | Back Side of Main Body ECU (Multiplex Network Body ECU) |
| *b | Rib Surrounding Instrument Panel Junction Block Assembly |
Check that the back side of the main body ECU (multiplex network body ECU) and the rib surrounding the instrument panel junction block assembly are the same height.
| *a | After Locking (Height Matches) | *b | Back Side of Main Body ECU (Multiplex Network Body ECU) |
| *c | Rib Surrounding Instrument Panel Junction Block Assembly | - | - |
|
Confirm Visually | - | - |
Attach the claw to install the junction block bracket to the instrument panel junction block assembly.
2.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (except Manual Transaxle)
Attach the wire harness clamp.
| *a | Lever Connector | - | - |
|
Rotate in this Direction | - | - |
Attach the claw to connect the 2 lever connectors.
Be sure to connect the connector securely.
Attach the claw to install the instrument panel junction block assembly with main body ECU to the connector holder.
Attach the claw to install the instrument panel junction block assembly with main body ECU with the 2 nuts.
Connect the 5 connectors.
| *a | Lever Connector |
|
Rotate in this Direction |
Connect the 2 connectors.
Attach the wire harness clamp.
Attach the claw to connect the 2 lever connectors.
Be sure to connect the connector securely.
| *a | w/ Clearance Warning System |
w/ Clearance Warning System:
Connect the 5 connectors.
w/o Clearance Warning System:
Connect the 4 connectors.
Attach the 2 wire harness clamps.
55308B
3.INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY (except Manual Transaxle)
|
Nut |
|
Bolt |
Install the No. 3 instrument panel to cowl brace sub-assembly with the nut and bolt.
Attach the 2 wire harness clamps.
73900
4.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (except Manual Transaxle)
89221
5.INSTALL MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (for Manual Transaxle)
Hold the main body ECU (multiplex network body ECU) with your dominant hand.
| *a | Connector |
Do not touch the connector.
Make sure foreign matter does not enter the terminals.
| *a | Fitting Surface |
Hold the instrument panel junction block assembly with your other hand.
Make sure there is no foreign matter in the fitting surface.
| *a | 20° or more |
|
Install in this Direction |
|
Housing Sidewall |
Set the guide of the main body ECU (multiplex network body ECU) against the housing sidewall.
Make sure the angle between the instrument panel junction block assembly and the main body ECU (multiplex network body ECU) is 20° or more.
|
Install in this Direction |
|
Housing Sidewall |
Slide the guide of the main body ECU (multiplex network body ECU) along the housing sidewall in the direction indicated by the arrow.
|
Install in this Direction |
|
Side A |
Slide it until it contacts side A.
|
Install in this Direction |
Contact side A.
Do not contact side A with the main body ECU (multiplex network body ECU) too hard.
| *a | Center of Rotation (Contacts Surface A) |
|
Rotate in this Direction |
| *a | Center of Rotation (Contacts Surface A) |
|
Rotate in this Direction |
While pressing the main body ECU (multiplex network body ECU) against side A (center of rotation) of the instrument panel junction block assembly, rotate it until it enters the lock of the instrument panel junction block assembly.
The center of rotation is the one that contacts surface A.
Rotate it until it enters the lock of the instrument panel junction block assembly.
| *a | Before Locking | *b | Main Body ECU (Multiplex Network Body ECU) Lock |
| *c | Instrument Panel Junction Block Assembly Lock | - | - |
|
Install in this Direction |
|
Pressing Area |
Press the pressing area of the main body ECU (multiplex network body ECU).
Press it in one of the following ways.
| *a | Press the 2 sides of the main body ECU (multiplex network body ECU) with both hands. | *b | Press the center of the main body ECU (multiplex network body ECU) with one hand. |
|
Place fingers or the palm of your hand here | - | - |
Do not hit on or put your weight on the main body ECU (multiplex network body ECU) when engaging the main body ECU (multiplex network body ECU).
Check the engagement of the main body ECU (multiplex network body ECU) and the instrument panel junction block assembly by the locking sound.
| *a | Back Side of Main Body ECU (Multiplex Network Body ECU) |
| *b | Rib Surrounding Instrument Panel Junction Block Assembly |
Check that the back side of the main body ECU (multiplex network body ECU) and the rib surrounding the instrument panel junction block assembly are the same height.
| *a | After Locking (Height Matches) | *b | Back Side of Main Body ECU (Multiplex Network Body ECU) |
| *c | Rib Surrounding Instrument Panel Junction Block Assembly | - | - |
|
Confirm Visually | - | - |
6.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for Manual Transaxle)
|
Rotate in this Direction |
Attach the claw to connect the 2 lever connectors.
Be sure to connect the connector securely.
Attach the 2 wire harness clamps.
|
Nut |
|
Bolt |
Attach the claw to install the instrument panel junction block assembly with main body ECU with the bolt and nut.
|
Nut |
|
Bolt |
Install the ECU integration box RH with the nut and bolt.
Connect the 3 connectors.
| *a | Lever Connector |
|
Rotate in this Direction |
Connect the 2 connectors.
Attach the claw to connect the 2 lever connectors.
Be sure to connect the connector securely.
Attach the 2 wire harness clamps.
Connect the connector.
55433B
7.INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL (for Manual Transaxle)
55550
8.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY (for Manual Transaxle)
55607
9.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for Manual Transaxle)
62111C
10.INSTALL COWL SIDE TRIM BOARD RH (for Manual Transaxle)
67913B
11.INSTALL FRONT DOOR SCUFF PLATE RH (for Manual Transaxle)
Use the same procedure described for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
58810J
12.INSTALL CONSOLE BOX ASSEMBLY (for Manual Transaxle)
13.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FKS:
for M20A-FKS:
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>INSTALLATION
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
65351A
14.INSTALL BATTERY HOLE COVER (for HV Model)
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>INSTALLATION
58416K
15.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>INSTALLATION
58410B
16.INSTALL DECK BOARD ASSEMBLY (for HV Model)
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>INSTALLATION
17. PERFORM DIAGNOSTIC SYSTEM CHECK
for HV Model with Occupant Classification System:
for Gasoline Model with Occupant Classification System:
w/o Occupant Classification System:
18.CHECK SRS WARNING LIGHT
for HV Model with Occupant Classification System:
for Gasoline Model with Occupant Classification System:
w/o Occupant Classification System: