Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The following procedure is for the LH side.
1.INSTALL FRONT SEAT ASSEMBLY LH
Place the front seat assembly LH in the vehicle as shown in the illustration.
2 or more people are required when reinstalling the front seat assembly LH into the vehicle.
Protect the front seat leg.
Be careful not to damage the front seat assembly LH, body exterior or interior parts.
Tilt the front seat assembly LH backward.
Be careful not to damage the front seat assembly LH or interior parts.
Connect the front seat airbag assembly LH connector.
| *A | for Driver Side | *B | for Front Passenger Side |
| *C | w/ Seat Heater System | *D | w/ Seat Heater System or w/ Climate Control Seat System |
| *E | w/ Occupant Classification System | - | - |
|
Front Seat Airbag Assembly Connector |
|
Front Seat Cushion Airbag Assembly RH Connector |
Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.
| *a | Correct | *b | Incorrect |
| *c | Yellow CPA | - | - |
Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).
Be careful not to damage the connector or wire harness of the front seat airbag assembly LH.
When connecting the connector, make sure to push it straight in.
Do not hold any parts other than the yellow CPA when connecting the connector.
If the upper portion of the yellow CPA is held when connecting the connector, the partial connection prevention mechanism will not function due to deformation of the yellow CPA. Therefore, hold the sides of the yellow CPA.
for Front Passenger Side, w/ Occupant Classification System:
Connect the front seat cushion airbag assembly RH connector.
Be careful not to damage the connector or wire harness of the front seat cushion airbag assembly RH.
When connecting the connector, make sure to push it straight in.
Connect each connector and attach the clamp under the front seat assembly LH.
Temporarily install the front seat assembly LH with the 4 "TORX" screws.
Operate the seat track adjusting handle and move the front seat assembly LH to the rearmost position.
Using a T50 "TORX" socket wrench, tighten the 2 "TORX" screws in the order shown in the illustration.
Operate the seat track adjusting handle and move the front seat assembly LH to the frontmost position.
Using a T50 "TORX" socket wrench, tighten the 2 "TORX" screws in the order shown in the illustration.
72138N
2.INSTALL REAR OUTER SEAT TRACK BRACKET COVER LH
|
Install in this Direction |
Attach the guide and claw to install the rear outer seat track bracket cover LH as shown in the illustration.
72158E
3.INSTALL REAR INNER SEAT TRACK BRACKET COVER LH
|
Install in this Direction |
Attach the guide and claw to install the rear inner seat track bracket cover LH as shown in the illustration.
72124
4.INSTALL FRONT OUTER SEAT TRACK BRACKET COVER LH
Operate the seat track adjusting handle and move the front seat assembly LH to the frontmost position.
|
Install in this Direction |
Attach the claw and guide to install the front outer seat track bracket cover LH as shown in the illustration.
72124A
5.INSTALL FRONT INNER SEAT TRACK BRACKET COVER LH
Use the same procedure described for the front outer seat track bracket cover LH.
71910A
6.INSTALL FRONT SEAT HEADREST ASSEMBLY
Install the front seat headrest assembly to the front seat assembly LH.
7.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FKS:
for M20A-FKS:
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>INSTALLATION
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
65351A
8.INSTALL BATTERY HOLE COVER (for HV Model)
58416K
9.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)
58410B
10.INSTALL DECK BOARD ASSEMBLY (for HV Model)
11. PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK (for Front Passenger Seat, w/ Occupant Classification System)
12.INSPECT SEAT HEATER SYSTEM (w/ Seat Heater System)
13.INSPECT CLIMATE CONTROL SEAT SYSTEM (w/ Climate Control Seat System)
for HV Model:
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM (for HV Model)>OPERATION CHECK
for Gasoline Model:
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM (for Gasoline Model)>OPERATION CHECK
14. PERFORM DIAGNOSTIC SYSTEM CHECK
for HV Model with Occupant Classification System:
for Gasoline Model with Occupant Classification System:
w/o Occupant Classification System:
15.CHECK SRS WARNING LIGHT
for HV Model with Occupant Classification System:
for Gasoline Model with Occupant Classification System:
w/o Occupant Classification System:
16.INSPECT SEAT BELT WARNING SYSTEM
w/ Occupant Classification System:
w/o Occupant Classification System: