Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Power Seat) › from 2019.02
RM3620E _58 Vehicle Interior _076405 SEAT _0372017 FRONT SEAT ASSEMBLY(for Power Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Power Seat)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:
·
B526553

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.INSTALL FRONT SEAT ASSEMBLY LH

a.
B526557

Place the front seat assembly LH in the vehicle as shown in the illustration.

NOTICE:
·

2 or more people are required when carrying the front seat assembly LH into the vehicle.

·

Protect the front seat legs.

·

Be careful not to damage the front seat assembly LH, body exterior or interior parts.




b.

Tilt the front seat assembly LH backward.

NOTICE:

Be careful not to damage the front seat assembly LH or interior parts.



c.
B526558C02
1.573,0.604 2.344,0.156 2.344,0.156 2.938,0.156 true 2.969,0.052 3.281,0.208 0.313,0.156 10 false *a
*a Front Seat Airbag Assembly LH Connector


Connect the front seat airbag assembly LH connector.

i.

Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

B345877C01
3.01,2.594 3.01,2.656 3.01,2.656 3.448,2.656 false 3,1.229 3,1.292 3,1.292 3.438,1.292 false 6.104,0.948 6.104,1.167 6.104,1.167 6.302,1.167 false 6.135,2.375 6.135,2.594 6.135,2.594 6.333,2.594 false 0.969,0.708 1.281,0.906 0.313,0.198 10 false *a 4.448,0.708 4.76,0.906 0.313,0.198 10 false *a 0.969,2.052 1.281,2.25 0.313,0.198 10 false *b 4.458,2.052 4.771,2.25 0.313,0.198 10 false *b 3.521,1.198 3.833,1.396 0.313,0.198 10 false *c 6.375,1.083 6.688,1.281 0.313,0.198 10 false *c 6.396,2.5 6.708,2.698 0.313,0.198 10 false *c 3.51,2.552 3.896,2.698 0.385,0.146 10 false *c
*a Correct *b Incorrect
*c Yellow CPA - -



ii.

Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

NOTICE:
·

Be careful not to damage the connector or wire harness of the front seat airbag assembly LH.

·

When connecting the connector, make sure to push it straight in.

·

Do not hold any parts other than the yellow CPA when connecting the connector.

·

If the upper portion of the yellow CPA is held when connecting the connector, the partial connection prevention mechanism will not function due to deformation of the yellow CPA. Therefore, hold the sides of the yellow CPA.





d.

Connect the other 2 connectors under the front seat assembly LH.


e.

Attach the clamp.


f.

Insert the location pin of the front seat assembly LH on the seat rail front side into the hole on the vehicle side.


g.

Temporarily install the front seat assembly LH with the 4 "TORX" screws.


h.

Connect the cable to the negative (-) auxiliary battery terminal.




iv.

for A25B-FXS:

Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION




i.

Operate the slide and vertical power seat switch knob and move the front seat assembly LH to the rearmost position.


j.
B526554N01
0.396,0.146 0.635,0.365 0.24,0.219 10 true (1) 1.333,1.427 1.573,1.646 0.24,0.219 10 true (2)

Using a T50 "TORX" socket wrench, tighten the 2 "TORX" screws in the order shown in the illustration.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


k.

Operate the slide and vertical power seat switch knob and move the front seat assembly LH to the frontmost position.


l.
B526555N01
0.823,1.135 1.052,1.365 0.229,0.229 10 true (2) 3.021,0.521 3.25,0.75 0.229,0.229 10 true (1)

Using a T50 "TORX" socket wrench, tighten the 2 "TORX" screws in the order shown in the illustration.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 72138N 2.INSTALL REAR OUTER SEAT TRACK BRACKET COVER LH

a.
B521463C02
0,0 0,0 false
V113147

Install in this Direction


Attach the guide and claw to install the rear outer seat track bracket cover LH as shown in the illustration.


Hide 72158E 3.INSTALL REAR INNER SEAT TRACK BRACKET COVER LH

a.
B521465C02
0,0 0,0 false
V113147

Install in this Direction


Attach the guide and claw to install the rear inner seat track bracket cover LH as shown in the illustration.


Hide 72124 4.INSTALL FRONT OUTER SEAT TRACK BRACKET COVER LH

a.

Operate the slide and vertical power seat switch knob and move the front seat assembly LH to the rearmost position.


b.
B526559C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and guide to install the front outer seat track bracket cover LH as shown in the illustration.


Hide 72124A 5.INSTALL FRONT INNER SEAT TRACK BRACKET COVER LH

HINT:

Use the same procedure described for the front outer seat track bracket cover LH.


Hide 71910A 6.INSTALL FRONT SEAT HEADREST ASSEMBLY

a.

Install the front seat headrest assembly to the front seat assembly LH.


Hide 65351A 7.INSTALL BATTERY HOLE COVER (for HV Model)

Hide 58416K 8.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 58410B 9.INSTALL DECK BOARD ASSEMBLY (for HV Model)

Hide 15.INSPECT SEAT HEATER SYSTEM (w/ Seat Heater System)

Hide 16.INSPECT CLIMATE CONTROL SEAT SYSTEM (w/ Climate Control Seat System)