When the power switch cannot be turned on (ACC) or on (IG), there may be a malfunction in interior certification, or the ACC relay or IG relay system. If interior certification does not succeed, the certification ECU (smart key ECU assembly) may be malfunctioning, or communication may not be possible between the No. 1 indoor electrical key antenna assembly (front floor), No. 1 indoor electrical key antenna assembly (rear floor) or No. 1 indoor electrical key antenna assembly (inside luggage compartment), the electrical key transmitter sub-assembly, and the door control receiver.
When the electrical key transmitter sub-assembly is brought into the cabin, the key ID code sent from the electrical key transmitter sub-assembly and the key ID code stored in the certification ECU (smart key ECU assembly) are certified. If these codes do not match and certification fails, the power switch cannot be turned on (ACC) or on (IG).
When the door is unlocked and the electrical key transmitter sub-assembly is brought into the cabin, the certification ECU (smart key ECU assembly) activates the indoor electrical key antenna and forms a detection area. When the electrical key transmitter sub-assembly is recognized inside the detection area, it returns the key ID code. This is received by the door control receiver, which then sends it to the certification ECU (smart key ECU assembly).
| Problem Symptom | Data List and Active Test |
|---|---|
| Power source mode does not change to on (IG) or on (ACC) | Power Source Control
·
Start Switch1 ·
Start Switch2 ·
IG Relay Monitor (Inside) ·
ACC Relay Monitor ·
IG Relay Monitor (Outside) ·
Latch Circuit ·
Power Supply Condition |
When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.
If the entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.
Inspect the fuses of circuits related to this system before performing the following procedure.
Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to the Service Bulletin.
After completing repairs, confirm that the problem does not recur.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
An antenna coil is connected between the terminals of the indoor electrical key antenna.
The door control receiver is also involved in interior certification.
If interior certification does not succeed, the History of Reason for Operation may remain in the certification ECU (smart key ECU assembly).
If the operation history remains, refer to the history table to determine the conditions and narrow down any trouble areas.
| Tester Display |
|---|
| Operation History |
Get into the vehicle while carrying the electrical key transmitter sub-assembly that has already been registered.
Change the shift state to park (P).
Check that the power source mode changes when the power switch is pressed without depressing the brake pedal.
| Result | Proceed to |
|---|---|
| Power source mode does not change when the electrical key transmitter sub-assembly is inside the push-button start function operation range only for the front side | A |
| Power source mode does not change when the electrical key transmitter sub-assembly is inside the push-button start function operation range only for the rear side | B |
| Power source mode does not change when the electrical key transmitter sub-assembly is inside the push-button start function operation range only for the luggage compartment | C |
| Power source mode does not change when the electrical key transmitter sub-assembly is inside any push-button start function operation range | D |
A
B
C
D
Install the transmitter battery to the electrical key transmitter sub-assembly.
Click hereGeneral>MAINTENANCE>TRANSMITTER BATTERY(w/ Entry and Start System)>REMOVAL
Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (front floor) and perform an entry and start system check.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).
As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
The hybrid control system starts when the electrical key transmitter sub-assembly is held near each indoor electrical key antenna assembly and the power switch is pressed with the brake pedal depressed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Utility / Communication Check(Key Diag Mode).
| *a | Inspection Point |
Check the No. 1 indoor electrical key antenna assembly (front floor).
When the electrical key transmitter sub-assembly is at either inspection point, check that the buzzer sounds.
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
It is possible to check which No. 1 indoor electrical key antenna assembly (front floor) is operating by the sounding of the buzzer.
When the buzzer does not sound for No. 1 indoor electrical key antenna assembly (front floor), it can be judged that the certification ECU (smart key ECU assembly), which controls the No. 1 indoor electrical key antenna assembly (front floor), is malfunctioning.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| Result | Proceed to |
|---|---|
| The buzzer sounds | A |
| The buzzer does not sound | B |
A
B
Disconnect the G54 certification ECU (smart key ECU assembly) connector.
Disconnect the G59 No. 1 indoor electrical key antenna assembly (front floor) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G54-8 (CLG5) - G59-1 (ANTE5) | Always | Below 1 Ω |
| G54-9 (CG5B) - G59-3 (CLGB) | Always | Below 1 Ω |
| G54-8 (CLG5) or G59-1 (ANTE5) - Other terminals and body ground | Always | 10 kΩ or higher |
| G54-9 (CG5B) or G59-3 (CLGB) - Other terminals and body ground | Always | 10 kΩ or higher |
Reconnect the G54 certification ECU (smart key ECU assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using an oscilloscope, check the waveform.
| *a | Front view of wire harness connector
(to No. 1 Indoor Electrical Key Antenna Assembly (Front Floor)) |
*b | Waveform |
| *c | For 30 seconds after closing any door | *d | After 30 seconds or more have elapsed since any door closed |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| G59-1 (ANTE5) - G59-3 (CLGB) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Install the transmitter battery to the electrical key transmitter sub-assembly.
Click here
Click hereGeneral>MAINTENANCE>TRANSMITTER BATTERY(w/ Entry and Start System)>REMOVAL
Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (rear floor) and perform an entry and start system check.
Check that the customize setting "Ignition Available Area" is set to "All".
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 1 indoor electrical key antenna assembly (rear floor).
As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
The hybrid control system starts when the electrical key transmitter sub-assembly is held near each indoor electrical key antenna assembly and the power switch is pressed with the brake pedal depressed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Utility / Communication Check(Key Diag Mode).
| *a | Inspection Point |
Check the No. 1 indoor electrical key antenna assembly (rear floor).
When the electrical key transmitter sub-assembly is at either inspection point, check that the buzzer sounds.
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
It is possible to check which No. 1 indoor electrical key antenna assembly (rear floor) is operating by the sounding of the buzzer.
When the buzzer does not sound for No. 1 indoor electrical key antenna assembly (rear floor), it can be judged that the certification ECU (smart key ECU assembly), which controls the No. 1 indoor electrical key antenna assembly (rear floor), is malfunctioning.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| Result | Proceed to |
|---|---|
| The buzzer sounds | A |
| The buzzer does not sound | B |
A
B
Disconnect the M7 certification ECU (smart key ECU assembly) connector.
Disconnect the N11 No. 1 indoor electrical key antenna assembly (rear floor) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M7-5 (CLG6) - N11-1 (ANTE6) | Always | Below 1 Ω |
| M7-6 (CG6B) - N11-3 (CLGB) | Always | Below 1 Ω |
| M7-5 (CLG6) or N11-1 (ANTE6) - Other terminals and body ground | Always | 10 kΩ or higher |
| M7-6 (CG6B) or N11-3 (CLGB) - Other terminals and body ground | Always | 10 kΩ or higher |
Reconnect the M7 certification ECU (smart key ECU assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using an oscilloscope, check the waveform.
| *a | Front view of wire harness connector
(to No. 1 Indoor Electrical Key Antenna Assembly (Rear Floor)) |
*b | Waveform |
| *c | For 30 seconds after closing any door | *d | After 30 seconds or more have elapsed since any door closed |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| N11-1 (ANTE6) - N11-3 (CLGB) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Install the transmitter battery to the electrical key transmitter sub-assembly.
Click hereGeneral>MAINTENANCE>TRANSMITTER BATTERY(w/ Entry and Start System)>REMOVAL
Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (inside luggage compartment) and perform an entry and start system check.
Check that the customize setting "Ignition Available Area" is set to "All".
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 1 indoor electrical key antenna assembly (inside luggage compartment).
As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
The hybrid control system starts when the electrical key transmitter sub-assembly is held near each indoor electrical key antenna assembly and the power switch is pressed with the brake pedal depressed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Utility / Communication Check(Key Diag Mode).
| *a | Inspection Point |
Check the No. 1 indoor electrical key antenna assembly (inside luggage compartment).
When the electrical key transmitter sub-assembly is at either inspection point, check that the buzzer sounds.
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
It is possible to check which No. 1 indoor electrical key antenna assembly (inside luggage compartment) is operating by the sounding of the buzzer.
When the buzzer does not sound for No. 1 indoor electrical key antenna assembly (inside luggage compartment), it can be judged that the certification ECU (smart key ECU assembly), which controls the No. 1 indoor electrical key antenna assembly (inside luggage compartment), is malfunctioning.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| Result | Proceed to |
|---|---|
| The buzzer sounds | A |
| The buzzer does not sound | B |
A
B
Disconnect the M7 certification ECU (smart key ECU assembly) connector.
Disconnect the M10 No. 1 indoor electrical key antenna assembly (inside luggage compartment) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M7-11 (CLG7) - M10-1 (ANTE7) | Always | Below 1 Ω |
| M7-10 (CG7B) - M10-3 (CLGB) | Always | Below 1 Ω |
| M7-11 (CLG7) or M10-1 (ANTE7) - Other terminals and body ground | Always | 10 kΩ or higher |
| M7-10 (CG7B) or M10-3 (CLGB) - Other terminals and body ground | Always | 10 kΩ or higher |
Reconnect the M7 certification ECU (smart key ECU assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using an oscilloscope, check the waveform.
| *a | Front view of wire harness connector
(to No. 1 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment)) |
*b | Waveform |
| *c | For 30 seconds after closing any door | *d | After 30 seconds or more have elapsed since any door closed |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| M10-1 (ANTE7) - M10-3 (CLGB) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.
Press and hold the lock switch of the electrical key transmitter sub-assembly for 5 seconds and check the number of times that the LED illuminates.
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. "Yes" is displayed for the Data List item "Key Low Battery" when this voltage information indicates 2.2 V or less.
Even if the transmitter battery is depleted, it is still possible to start the hybrid control system by holding the electrical key transmitter sub-assembly near the power switch, depressing the brake pedal and pressing the power switch.
| Result | Proceed to |
|---|---|
| LED illuminates 3 times or more when switch is pressed and held | A |
| LED does not illuminate when switch is pressed and held | B |
| LED illuminates once or twice but not a third time | C |
A
B
C
Check the vehicle specification.
| Result | Proceed to |
|---|---|
| w/ Entry Function | A |
| w/o Entry Function | B |
A
B
Check that the entry lock and unlock functions operate on each door.
If the door control receiver is defective, code verification does not begin in the cabin and the entry lock and unlock functions do not operate.
| Result | Proceed to |
|---|---|
| Entry lock/unlock functions operate normally | A |
| An entry lock/unlock functions does not operate normally | B |
A
B
Check that the wireless door lock control system operate.
If the door control receiver is defective, code verification does not begin in the cabin and the wireless door lock control system do not operate.
| Result | Proceed to |
|---|---|
| Wireless door lock control system operate normally | A |
| A wireless door lock control system does not operate normally | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Start Switch1 | Power switch 1 status | OFF or ON | OFF: Power switch not pressed
ON: Power switch pressed |
·
If the power switch is pressed for a short time, the display may not change. ·
Use this item to determine if the power switch input signal is malfunctioning. |
| Start Switch2 | Power switch 2 status | OFF or ON | OFF: Power switch not pressed
ON: Power switch pressed |
·
Backup for power switch 1. However, when the power switch is pressed and held, the power source mode can only be changed when both power switch 1 and 2 are normal. ·
Behaves the same way as power switch 1. |
| Tester Display |
|---|
| Start Switch1 |
| Start Switch2 |
The GTS display changes correctly in response to the power switch operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage while confirming the power source mode on the Data List.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Power Supply Condition | Power supply state | All OFF, ACC ON, IG ON or ST ON | All OFF: Power switch off
ACC ON: Power switch on (ACC) IG ON: Power switch on (IG) ST ON: Sending hybrid control system start request signal |
- |
| Tester Display |
|---|
| Power Supply Condition |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G54-17 (IG1D) - Body ground | Power switch off | 1 V or less |
| Power switch on (ACC) | ||
| Power switch on (IG) | 9 V or higher | |
| G54-16 (ACCD) - Body ground | Power switch off | 1 V or less |
| Power switch on (ACC) | 8.5 V or higher | |
| Power switch on (IG) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
Disconnect the instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4D-3 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Inspect the transmitter battery.
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Entry and Start System)>INSPECTION
Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the power switch.
for A25A-FXS:
Click hereEngine / Hybrid System>A25A-FXS (STARTING)>POWER SWITCH>REMOVAL
for A25B-FXS:
Click hereEngine / Hybrid System>A25B-FXS (STARTING)>POWER SWITCH>REMOVAL
Inspect the power switch.
for A25A-FXS:
Click hereEngine / Hybrid System>A25A-FXS (STARTING)>POWER SWITCH>INSPECTION
for A25B-FXS:
Click hereEngine / Hybrid System>A25B-FXS (STARTING)>POWER SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for A25A-FXS:
Click hereEngine / Hybrid System>A25A-FXS (STARTING)>POWER SWITCH>REMOVAL
for A25B-FXS:
Click hereEngine / Hybrid System>A25B-FXS (STARTING)>POWER SWITCH>REMOVAL
Disconnect the G54 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G54-23 (SSW1) - G55-5 (SS1) | Always | Below 1 Ω |
| G54-21 (SSW2) - G55-1 (SS2) | Always | Below 1 Ω |
| G54-11 (AGND) - G55-6 (AGND) | Always | Below 1 Ω |
| G54-23 (SSW1) or G55-5 (SS1) - Other terminals and body ground | Always | 10 kΩ or higher |
| G54-21 (SSW2) or G55-1 (SS2) - Other terminals and body ground | Always | 10 kΩ or higher |
| G54-11 (AGND) or G55-6 (AGND) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG