Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (for HV Model, with Entry and Start System)
RM3620E _58 Vehicle Interior _076046 DOOR LOCK _0370164 WIRELESS DOOR LOCK CONTROL SYSTEM(for HV Model, with Entry and Start System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(for HV Model, with Entry and Start System)  Only Wireless Control Function is Inoperative  


DESCRIPTION

If the wireless door lock operations cannot be performed, the door control receiver may be malfunctioning, or there may be wave interference or problems in the communication which is used for the wireless function between the door control receiver and certification ECU (smart key ECU assembly).

WIRING DIAGRAM

E402861E08
1.448,0.396 3.198,0.76 1.75,0.365 10 false ECU-DCC NO.2 1.396,0.813 3.146,1.177 1.75,0.365 10 false to Each IG Relay 1.25,1.198 3,1.563 1.75,0.365 10 false to Each ACC Relay 1.146,1.802 2.896,2.167 1.75,0.365 10 false from Auxiliary Battery 3.094,1.99 3.875,2.24 0.781,0.25 10 false AM2 5.385,0.385 6.167,0.635 0.781,0.25 10 false CUTB 5.375,0.823 6.156,1.073 0.781,0.25 10 false IG1D 5.365,1.115 6.146,1.365 0.781,0.25 10 false ACCD 5.385,1.698 6.167,1.948 0.781,0.25 10 false +B 5.052,0.188 5.833,0.438 0.781,0.25 10 false 15 5.063,0.615 5.844,0.865 0.781,0.25 10 false 17 5.052,1.021 5.833,1.271 0.781,0.25 10 false 16 5.115,1.615 5.896,1.865 0.781,0.25 10 false 4 5.021,0.385 5.802,0.635 0.781,0.25 10 false G54 5.021,0.823 5.802,1.073 0.781,0.25 10 false G54 5.021,1.229 5.802,1.479 0.781,0.25 10 false G54 5.01,1.823 5.792,2.073 0.781,0.25 10 false G54 6.073,0.771 6.854,1.021 0.781,0.25 10 false +B 6.052,1.365 6.833,1.615 0.781,0.25 10 false +B 6.354,1.344 6.979,1.76 0.625,0.417 10 false IC 6.094,4.073 6.875,4.323 0.781,0.25 10 false +B 6.135,4.698 6.917,4.948 0.781,0.25 10 false +B 6.125,3.385 6.906,3.635 0.781,0.25 10 false 5 V 5.375,3.729 6.156,3.979 0.781,0.25 10 false RCO 5.396,4.354 6.177,4.604 0.781,0.25 10 false RDAM 5.385,5.021 6.167,5.271 0.781,0.25 10 false CSEL 5.396,5.667 6.177,5.917 0.781,0.25 10 false E 5.031,3.833 5.813,4.083 0.781,0.25 10 false M7 5.031,4.458 5.813,4.708 0.781,0.25 10 false M7 5.042,5.135 5.823,5.385 0.781,0.25 10 false M7 5,5.667 5.781,5.917 0.781,0.25 10 false G54 5.063,3.635 5.844,3.885 0.781,0.25 10 false 18 5.073,4.25 5.854,4.5 0.781,0.25 10 false 19 5.063,4.927 5.844,5.177 0.781,0.25 10 false 20 5.052,5.458 5.833,5.708 0.781,0.25 10 false 18 2.281,5.74 3.063,5.99 0.781,0.25 10 false M11 2.281,5.135 3.063,5.385 0.781,0.25 10 false M11 2.281,4.448 3.063,4.698 0.781,0.25 10 false M11 2.292,3.844 3.073,4.094 0.781,0.25 10 false M11 1.938,3.281 2.719,3.531 0.781,0.25 10 false M8 1.948,3.844 2.729,4.094 0.781,0.25 10 false M8 1.958,4.458 2.74,4.708 0.781,0.25 10 false M8 1.948,5.135 2.729,5.385 0.781,0.25 10 false M8 1.948,5.729 2.729,5.979 0.781,0.25 10 false M8 1.635,3.271 2.031,3.542 0.396,0.271 10 false IG 1.615,3.698 2.01,3.969 0.396,0.271 10 false +5 1.448,4.365 1.844,4.635 0.396,0.271 10 false DATA 1.448,5.042 1.844,5.313 0.396,0.271 10 false CSEL 1.521,5.708 1.917,5.979 0.396,0.271 10 false GND 0.667,4.25 1.292,4.667 0.625,0.417 10 false IC 0.896,2.448 2.646,2.813 1.75,0.365 10 false from ECU-IG1 NO.4 Fuse 2,3.083 2.396,3.354 0.396,0.271 10 false 1 2.01,3.646 2.406,3.917 0.396,0.271 10 false 8 2,4.25 2.396,4.521 0.396,0.271 10 false 2 2.01,4.917 2.406,5.188 0.396,0.271 10 false 6 1.948,5.521 2.344,5.792 0.396,0.271 10 false 12 2.375,4.917 2.771,5.188 0.396,0.271 10 false 2 2.354,5.531 2.75,5.802 0.396,0.271 10 false 1 2.365,3.635 2.76,3.917 0.396,0.281 10 false 4 2.365,4.25 2.76,4.531 0.396,0.281 10 false 5 0.469,6.167 2.458,6.573 1.99,0.406 10 false Door Control Receiver 0.698,8.406 2.688,8.813 1.99,0.406 10 false : CAN Communication Line 0.156,7.594 4.135,8.042 3.979,0.448 10 false Main Body ECU (Multiplex Network Body ECU) 4.281,7.615 7.115,8.24 2.833,0.625 10 false Certification ECU (Smart Key ECU Assembly) 4.208,8.115 7.042,8.74 2.833,0.625 10 false *1: for 12 Pin Type 4.219,8.417 6.969,8.865 2.75,0.448 10 false *2: for 5 Pin Type 1.958,3.49 2.354,3.76 0.396,0.271 10 false *1 1.958,4.063 2.354,4.333 0.396,0.271 10 false *1 1.969,4.677 2.365,4.948 0.396,0.271 10 false *1 1.948,5.354 2.365,5.594 0.417,0.24 10 false *1 1.969,5.938 2.385,6.177 0.417,0.24 10 false *1 2.344,4.052 2.76,4.292 0.417,0.24 10 false *2 2.323,4.677 2.74,4.917 0.417,0.24 10 false *2 2.313,5.344 2.729,5.583 0.417,0.24 10 false *2 2.302,5.948 2.719,6.188 0.417,0.24 10 false *2

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (for HV Model, with Entry and Start System)>DTC CHECK / CLEAR

·

for 12 Pin Type:

It is necessary to perform initialization after registration of the transmitter IDs into the door control receiver if the door control receiver has been replaced.




PROCEDURE

1.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Measure the auxiliary battery voltage with the power switch off.

Standard voltage:

11 to 14 V


HINT:

It may be possible to tell whether the auxiliary battery is discharged by operating the horn.

If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.



Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.


b.

Connect the GTS to the DLC3.


c.

Check for DTCs.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (for HV Model, with Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.CHECK DOOR AJAR WARNING

B

3.CHECK DOOR AJAR WARNING
a.

When the doors are locked by operating the wireless door lock function with all doors closed, check that the door ajar warning operates.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (for HV Model, with Entry and Start System)>OPERATION CHECK

HINT:

Be sure to check the following before performing the procedure.

·

Power switch is off.

·

All the doors are closed.

·

The lock switch is pressed on the electrical key transmitter sub-assembly.

·

Electrical key transmitter sub-assembly is in the vehicle exterior detection area.




Result:
Result Proceed to
The buzzer does not sound A
The buzzer sounds B



A

4.CHECK POWER DOOR LOCK CONTROL SYSTEM

B

GO TO LIGHTING SYSTEM (Proceed to Door Courtesy Switch Circuit)

4.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Power door lock function operates normally A
Power door lock function does not operate normally B



A

5.CHECK WAVE ENVIRONMENT

B

5.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless operation 2 or more times*.

*: When the wireless function is operated, channel 1 and 2 are used alternately. If the first wireless operation is performed successfully and the second wireless operation fails, wave interference may be occurring for either channel.


HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.




Result:
Result Proceed to
Wireless function does not operate normally A
Wireless function operates normally B



A

6.CHECK TRANSMITTER BATTERY

B

AFFECTED BY WAVE INTERFERENCE

6.CHECK TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

i.

Press and hold the lock switch of the electrical key transmitter sub-assembly for 5 seconds and check the number of times that the LED illuminates.

HINT:
·

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. "Yes" is displayed for the Data List item "Key Low Battery" when this voltage information indicates 2.2 V or less.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function, HV Model)>DATA LIST / ACTIVE TEST

·

Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter sub-assembly near the power switch, depressing the brake pedal and pressing the power switch.





Result:
Result Proceed to
LED illuminates 3 times or more when switch is pressed and held A
LED does not illuminate when switch is pressed and held B
LED illuminates once or twice but not a third time C



A

7.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

22.INSPECT TRANSMITTER BATTERY

C

7.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.


Result:
Result Proceed to
Another registered electrical key transmitter sub-assembly is not available A
Another registered electrical key transmitter sub-assembly is available B



A

8.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

9.CHECK WIRELESS DOOR LOCK OPERATION
8.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.CHECK WIRELESS DOOR LOCK OPERATION
9.CHECK WIRELESS DOOR LOCK OPERATION
a.

Using another registered electrical key transmitter sub-assembly, check that the function operates normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (for HV Model, with Entry and Start System)>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock function does not operate normally A
Wireless door lock function operates normally B



A

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

B

10.PERFORM REGISTRATION
10.PERFORM REGISTRATION
a.

Perform registration of the B code.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

11.CHECK WIRELESS DOOR LOCK OPERATION
11.CHECK WIRELESS DOOR LOCK OPERATION
a.

After completing B code registration, check that the entry lock and unlock functions can be operated 2 times consecutively.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (for HV Model, with Entry and Start System)>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock function does not operate normally A
Wireless door lock function operates normally B



A

12.READ VALUE USING GTS (B CODE)

B

END (B CODE REGISTRATION FAILED)

12.READ VALUE USING GTS (B CODE)
a.

Enter the following menus: Body Electrical / Entry&Start / Data List.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
B Code B code registration status No Regd or Regd No Regd: B code not registered correctly
Regd: B code registered correctly
-
Body Electrical > Entry&Start > Data List
Tester Display
B Code
50003 125 132

Result:
Result Proceed to
"No Regd" is displayed on the GTS A
"Regd" is displayed on the GTS B



A

13.READ VALUE USING GTS (B CODE DIFFERENCE)

B

13.READ VALUE USING GTS (B CODE DIFFERENCE)
a.

Enter the following menus: Body Electrical / Entry&Start / Data List.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
B Code Difference B code mismatch No or Yes No: Communication normal
Yes: Communication malfunction
-
Body Electrical > Entry&Start > Data List
Tester Display
B Code Difference
50003 125 131

Result:
Result Proceed to
"No" is displayed on the GTS A
"Yes" is displayed on the GTS B



A

14.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

14.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Measure the voltage while checking the Data List on the GTS.

i.

Enter the following menus: Body Electrical / Power Source Control / Data List.


ii.

Read the Data List according to the display on the GTS.

B473193C11
4.563,0.469 4.958,0.698 0.396,0.229 4.01,2.188 4.219,1.302 true 4.5,2.198 4.385,1.302 true 4.635,0.5 4.948,0.698 0.313,0.198 10 false G54 3.854,2.229 4.281,2.458 0.427,0.229 10 false IG1D 0.198,0.156 0.51,0.354 0.313,0.198 10 false *a 4.344,2.229 4.802,2.438 0.458,0.208 10 false ACCD
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state All OFF, ACC ON, IG ON or ST ON All OFF: Power switch off
ACC ON: Power switch on (ACC)
IG ON: Power switch on (IG)
ST ON: Sending hybrid control system start request signal
-
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 223 18
Standard Voltage:
Tester Connection Switch Condition Specified Condition
G54-17 (IG1D) - Body ground Power switch off Below 1 V
Power switch on (ACC) Below 1 V
Power switch on (IG) 9 V or higher
G54-16 (ACCD) - Body ground Power switch off Below 1 V
Power switch on (ACC) 8.5 V or higher
Power switch on (IG) 8.5 V or higher




Result:
Proceed to
OK
NG



OK

15.READ VALUE USING GTS (ACC SW, IG SW)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

15.READ VALUE USING GTS (ACC SW, IG SW)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ACC SW Power switch status OFF or ON OFF: Power switch off
ON: Power switch on (ACC)
"ON" is also displayed when the power switch is on (IG).
IG SW Power switch status OFF or ON OFF: Power switch off
ON: Power switch on (IG)
"OFF" is also displayed when the power switch is on (ACC).
Body Electrical > Main Body > Data List
Tester Display
ACC SW
IG SW
50003 123 31,30
HINT:

If the main body ECU (multiplex network body ECU) misjudges for any reason that the power switch is on (IG) even though the power switch is off, the wireless lock and unlock functions will be disabled.



Result:
Result Proceed to
The main body ECU (multiplex network body ECU) judges properly that the power source is off when the power switch is off A
The main body ECU (multiplex network body ECU) does not judge properly that the power source is off when the power switch is off B



A

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER AND BODY GROUND)

B

TROUBLESHOOT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER AND BODY GROUND)
a.

Disconnect the M7 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the M8*1 or M11*2 door control receiver connector.

*1: for 12 Pin Type

*2: for 5 Pin Type



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 12 Pin Type:
Tester Connection Condition Specified Condition
M7-18 (RCO) - M8-8 (+5) Always Below 1 Ω
M7-19 (RDAM) - M8-2 (DATA) Always Below 1 Ω
M7-20 (CSEL) - M8-6 (CSEL) Always Below 1 Ω
M8-12 (GND) - Body ground Always Below 1 Ω
M7-18 (RCO) or M8-8 (+5) - Other terminals and body ground Always 10 kΩ or higher
M7-19 (RDAM) or M8-2 (DATA) - Other terminals and body ground Always 10 kΩ or higher
M7-20 (CSEL) or M8-6 (CSEL) - Other terminals and body ground Always 10 kΩ or higher


for 5 Pin Type:
Tester Connection Condition Specified Condition
M7-18 (RCO) - M11-4 (+5) Always Below 1 Ω
M7-19 (RDAM) - M11-5 (DATA) Always Below 1 Ω
M7-20 (CSEL) - M11-2 (CSEL) Always Below 1 Ω
M11-1 (GND) - Body ground Always Below 1 Ω
M7-18 (RCO) or M11-4 (+5) - Other terminals and body ground Always 10 kΩ or higher
M7-19 (RDAM) or M11-5 (DATA) - Other terminals and body ground Always 10 kΩ or higher
M7-20 (CSEL) or M11-2 (CSEL) - Other terminals and body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

17.CHECK WIRELESS DOOR LOCK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK WIRELESS DOOR LOCK OPERATION
a.

Connect all connectors and check that the function operates normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (for HV Model, with Entry and Start System)>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock function does not operate normally A
Wireless door lock function operates normally B



A

18.CHECK DOOR CONTROL RECEIVER

B

END (CONNECTOR WAS NOT CONNECTED SECURELY)

18.CHECK DOOR CONTROL RECEIVER
a.
B532420C01
1.5,0.375 1.885,0.646 0.385,0.271 1.521,2.469 1.927,2.729 0.406,0.26 2.052,1.271 2.344,1.896 true 1.385,3.604 1.115,4.052 true 0.229,0.104 0.542,0.313 0.313,0.208 12 false *A 0.26,2.208 0.563,2.438 0.302,0.229 12 false *B 0.781,0.427 0.99,0.625 0.208,0.198 10 false *a 0.813,2.521 1.021,2.719 0.208,0.198 10 false *a 1.635,2.521 2.042,2.719 0.406,0.198 10 false M8 2.208,1.906 2.625,2.104 0.417,0.198 10 false GND 0.979,4.094 1.396,4.292 0.417,0.198 10 false GND 1.563,0.438 1.969,0.635 0.406,0.198 10 false M11
*A for 5 Pin Type
*B for 12 Pin Type
*a Component with harness connected
(Door Control Receiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 5 Pin Type:
Tester Connection Condition Specified Condition
M11-1 (GND) - Body ground Always Below 1 Ω

for 12 Pin Type:
Tester Connection Condition Specified Condition
M8-12 (GND) - Body ground Always Below 1 Ω



b.

Using an oscilloscope, check the waveform.

C395410C11
1.406,0.302 1.781,0.521 0.375,0.219 5.302,0.302 5.677,0.521 0.375,0.219 1.115,1.667 1.323,1.333 true 2.042,1.677 1.781,1.198 true 5,1.531 5.208,1.198 true 6.083,1.583 5.75,1.177 true 0.396,0.229 0.771,0.469 0.375,0.24 12 false *A 4.344,0.198 4.729,0.406 0.385,0.208 12 false *B 0.771,0.51 1.083,0.667 0.313,0.156 10 false *a 2.594,1.844 2.906,2 0.313,0.156 10 false *b 2.833,3.333 3.146,3.49 0.313,0.156 10 false *c 3.958,3.323 4.271,3.479 0.313,0.156 10 false *d 1.5,0.344 1.906,0.531 0.406,0.188 10 false M8 4.583,0.5 4.896,0.656 0.313,0.156 10 false *a 2.208,2.604 2.521,2.76 0.313,0.156 10 false GND 0.979,1.719 1.292,1.875 0.313,0.156 10 false GND 2,1.698 2.406,1.865 0.406,0.167 10 false DATA 4.698,1.594 5.104,1.76 0.406,0.167 10 false DATA 5.99,1.583 6.302,1.74 0.313,0.156 10 false GND 5.375,0.344 5.771,0.552 0.396,0.208 10 false M11
*A for 12 Pin Type *B for 5 Pin Type
*a Component with harness connected
(Door Control Receiver)
*b Waveform 1
*c Before lock or unlock switch of electrical key transmitter sub-assembly pressed *d After lock or unlock switch of electrical key transmitter sub-assembly pressed


OK:
for 12 Pin Type:
Tester Connection Condition Tool Setting Specified Condition
M8-2 (DATA) - M8-12 (GND) Procedure:
1.

Power switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


5 V/DIV., 500 ms/DIV. Below 1 V → Pulse generation
(See waveform 1)

for 5 Pin Type:
Tester Connection Condition Tool Setting Specified Condition
M11-5 (DATA) - M11-1 (GND) Procedure:
1.

Power switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


5 V/DIV., 500 ms/DIV. Below 1 V → Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

19.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE DOOR CONTROL RECEIVER

19.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B532420C02
1.5,0.375 1.885,0.646 0.385,0.271 1.521,2.469 1.927,2.729 0.406,0.26 2.052,1.271 2.719,1.865 true 1.385,3.604 1.125,4.031 true 1.896,1.281 2.24,1.865 true 1.354,3.385 0.885,3.802 true 2.115,3.385 2.677,3.917 true 0.26,0.146 0.583,0.396 0.323,0.25 12 false *A 0.281,2.135 0.583,2.354 0.302,0.219 12 false *B 0.781,0.427 0.99,0.625 0.208,0.198 10 false *a 0.813,2.521 1.021,2.719 0.208,0.198 10 false *a 1.563,0.438 1.917,0.677 0.354,0.24 10 false M11 2.615,1.885 3.031,2.083 0.417,0.198 10 false GND 1.625,2.521 1.979,2.719 0.354,0.198 10 false M8 0.99,4.083 1.406,4.281 0.417,0.198 10 false GND 2.125,1.885 2.583,2.156 0.458,0.271 10 false CSEL 0.573,3.813 0.99,4.01 0.417,0.198 10 false CSEL 2.646,3.948 3.063,4.146 0.417,0.198 10 false IG
*A for 5 Pin Type
*B for 12 Pin Type
*a Component with harness connected
(Door Control Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 5 Pin Type:
Tester Connection Condition Specified Condition
M11-2 (CSEL) - M11-1 (GND) Procedure:
1.

Power switch off

2.

All doors closed


Below 1 V → Pulse generation

for 12 Pin Type:
Tester Connection Condition Specified Condition
M8-1 (IG) - M8-12 (GND) Power switch on (IG) 10 to 16 V
M8-6 (CSEL) - M8-12 (GND) Procedure:
1.

Power switch off

2.

All doors closed


Below 1 V → Pulse generation



b.

Using an oscilloscope, check the waveform.

C395411C07
1.448,0.375 1.781,0.594 0.333,0.219 5.323,0.375 5.656,0.594 0.333,0.219 1.073,1.667 1.323,1.344 true 1.958,1.688 1.76,1.323 true 5.031,1.552 5.354,1.177 true 6.073,1.521 5.75,1.177 true 0.49,0.24 0.844,0.417 0.354,0.177 12 false *A 4.365,0.271 4.698,0.5 0.333,0.229 12 false *B 0.76,0.51 1.073,0.667 0.313,0.156 10 false *a 2.625,1.781 2.938,1.938 0.313,0.156 10 false *b 2.865,3.302 3.177,3.458 0.313,0.156 10 false *c 3.854,3.323 4.167,3.479 0.313,0.156 10 false *d 4.667,0.531 4.979,0.688 0.313,0.156 10 false *a 2.229,2.594 2.573,2.75 0.344,0.156 10 false GND 1.51,0.427 1.823,0.625 0.313,0.198 10 false M8 2.01,1.677 2.323,1.875 0.313,0.198 10 false +5 0.948,1.698 1.292,1.854 0.344,0.156 10 false GND 4.948,1.594 5.26,1.792 0.313,0.198 10 false +5 6.021,1.552 6.365,1.708 0.344,0.156 10 false GND 5.365,0.417 5.677,0.615 0.313,0.198 10 false M11
*A for 12 Pin Type *B for 5 Pin Type
*a Component with harness connected
(Door Control Receiver)
*b Waveform 1
*c Before lock or unlock switch of electrical key transmitter sub-assembly pressed *d After lock or unlock switch of electrical key transmitter sub-assembly pressed


OK:
for 12 Pin Type:
Tester Connection Condition Tool Setting Specified Condition
M8-8 (+5) - M8-12 (GND) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)

for 5 Pin Type:
Tester Connection Condition Tool Setting Specified Condition
M11-4 (+5) - M11-1(GND) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

20.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

20.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one and perform registration again.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

21.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
21.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM

Result:
Result Proceed to
Wireless door lock function operates normally A
Wireless door lock function does not operate normally B



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

22.INSPECT TRANSMITTER BATTERY
a.

Inspect the transmitter battery.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Entry and Start System)>INSPECTION

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG