Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model) › from 2019.09
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0369994 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  Engine does not Start  


DESCRIPTION

except Manual Transaxle:

When the electrical key transmitter sub-assembly is in the cabin and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the shift state is park (P) and the brake pedal is depressed, the engine can be started by pressing the engine switch. If the steering is unlocked, the engine can also be started by pressing the engine switch with the shift state park (P) and the brake pedal depressed.


for Manual Transaxle:

When the electrical key transmitter sub-assembly is in the cabin and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the clutch pedal is depressed, the engine can be started by pressing the engine switch. If the steering is unlocked, the engine can also be started by pressing the engine switch with the clutch pedal depressed.


Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Engine does not Start
Power Source Control
·

Stop Light Switch1*1

·

Steering Unlock Switch

·

Shift P Signal Pulse*1

·

IG Relay Monitor (Inside)

·

IG Relay Monitor (Outside)

·

Latch Circuit

·

Starter Request Signal

·

Power Supply Condition


Entry&Start
·

Immobiliser

·

Engine Start Request

·

S Code Check*2

·

L Code Check


Starting Control
·

Starter SW

·

Shift Position Status*1

·

Ignition



*1: except Manual Transaxle

*2: w/o Occupant Classification System


WIRING DIAGRAM

w/ Stop and Start System


except Manual Transaxle:
E407997E04
5.042,2.198 5.5,2.396 0.458,0.198 10 false STA 5.052,0.531 5.51,0.729 0.458,0.198 10 false STAR 5.031,1.24 5.49,1.438 0.458,0.198 10 false STP1 5.76,3.146 6.219,3.344 0.458,0.198 10 false P 6,2.927 6.458,3.125 0.458,0.198 10 false 22 4.729,1.146 5.188,1.344 0.458,0.198 10 false 25 4.76,0.448 5.219,0.646 0.458,0.198 10 false 9 4.729,2.104 5.188,2.302 0.458,0.198 10 false 20 5.677,0.542 6.135,0.74 0.458,0.198 10 false IC 5.656,1.448 6.115,1.646 0.458,0.198 10 false IC 5.656,2.438 6.115,2.635 0.458,0.198 10 false IC 5.063,0.198 5.521,0.396 0.458,0.198 10 false +B 0.542,1.875 1,2.073 0.458,0.198 10 false STA 0.479,0.646 0.938,0.844 0.458,0.198 10 false NSW 0.573,1.219 1.031,1.417 0.458,0.198 10 false STP 0.26,2.573 0.719,2.771 0.458,0.198 10 false ECM 6.583,3.135 7.042,3.333 0.458,0.198 10 false P2 6.583,4.125 7.042,4.323 0.458,0.198 10 false STP 4.854,4.74 5.313,4.938 0.458,0.198 10 false STP 4.885,7.365 5.344,7.563 0.458,0.198 10 false STOP 3,3.5 3.458,3.698 0.458,0.198 10 false B 3.385,3.5 3.844,3.698 0.458,0.198 10 false L 2.635,3.76 3.094,3.958 0.458,0.198 10 false P 2.625,4.042 3.083,4.24 0.458,0.198 10 false N 0.49,4.031 0.948,4.229 0.458,0.198 10 false STA2 0.563,3.052 1.021,3.25 0.458,0.198 10 false CLL 2.115,4.438 3.438,5.604 1.323,1.167 10 false Park/Neutral Position Switch Assembly 0.094,5.5 2.177,6.135 2.083,0.635 10 false Engine Stop and Start ECU 0.688,5.958 2.771,6.594 2.083,0.635 10 false from Battery 1.031,8.01 2.323,8.344 1.292,0.333 10 false ST NO. 1 0.333,7.656 1.625,7.99 1.292,0.333 10 false ST NO.1 1.01,9.417 2.302,9.75 1.292,0.333 10 false Starter Assembly 1.083,8.792 1.542,8.99 0.458,0.198 10 false B 2.146,9.156 2.604,9.354 0.458,0.198 10 false SL1 2.167,8.802 2.625,9 0.458,0.198 10 false SL2 5.75,4.479 7.156,5.417 1.406,0.938 10 false Shift Lock Control Unit Assembly 4.542,3.594 6.406,4.333 1.865,0.74 10 false Certification ECU (Smart Key ECU Assembly) 5.094,8.583 7.135,8.896 2.042,0.313 10 false Stop Light Switch Assembly 5.896,7.958 6.354,8.156 0.458,0.198 10 false IC 5.948,7.198 7.115,8 1.167,0.802 10 false from Battery 4.875,6.115 6.344,6.813 1.469,0.698 10 false STP 5.49,7.74 5.948,7.938 0.458,0.198 10 false B 5.49,8.063 6.292,8.271 0.802,0.208 10 false L 6.115,8.25 6.573,8.448 0.458,0.198 10 false GND 4.677,2.271 5.135,2.469 0.458,0.198 10 false A15 4.667,0.635 5.125,0.833 0.458,0.198 10 false A15 4.708,1.323 5.167,1.521 0.458,0.198 10 false M7 5.948,3.115 6.406,3.313 0.458,0.198 10 false G54 0.979,1.75 1.438,1.948 0.458,0.198 10 false 30 0.927,0.542 1.385,0.74 0.458,0.198 10 false 23 0.958,1.24 1.417,1.438 0.458,0.198 10 false 21 0.063,2.406 1.302,2.625 1.24,0.219 10 false A24 0.281,1.5 0.74,1.698 0.458,0.198 10 false IC 3.198,3.229 3.656,3.427 0.458,0.198 10 false 4 3.698,3.74 4.156,3.938 0.458,0.198 10 false 9 *1 2.125,4.271 2.583,4.469 0.458,0.198 10 false C31 0.104,5.344 0.563,5.542 0.458,0.198 10 false A34 0.906,2.917 1.365,3.115 0.458,0.198 10 false 17 0.969,3.948 1.427,4.146 0.458,0.198 10 false 23 5.104,8.427 5.563,8.625 0.458,0.198 10 false A40 1.052,7.656 1.51,7.854 0.458,0.198 10 false 1 1.719,7.656 2.177,7.854 0.458,0.198 10 false 2 1.729,7.365 2.188,7.563 0.458,0.198 10 false 3 1.073,7.396 1.531,7.594 0.458,0.198 10 false 5 0.75,8.594 1.208,8.792 0.458,0.198 10 false 1 2.604,9 3.063,9.198 0.458,0.198 10 false 2 2.594,8.573 3.052,8.771 0.458,0.198 10 false 1 0.708,8.813 1.167,9.01 0.458,0.198 10 false D1 2.531,9.188 2.99,9.385 0.458,0.198 10 false C43 2.531,8.802 2.99,9 0.458,0.198 10 false C43 5.302,8.042 5.76,8.24 0.458,0.198 10 false 3 5.292,7.646 5.75,7.844 0.458,0.198 10 false 7 6.594,8.135 7.052,8.333 0.458,0.198 10 false 2 6.406,3.052 6.865,3.25 0.458,0.198 10 false 3 6.417,4.031 6.875,4.229 0.458,0.198 10 false 4 4.552,5.229 5.01,5.427 0.458,0.198 10 false A39 4.625,4.615 5.083,4.813 0.458,0.198 10 false 41 4.552,5.406 6.719,6.094 2.167,0.688 10 false Skid Control ECU Assembly 5.75,4.344 6.208,4.542 0.458,0.198 10 false G26 4.49,6.813 6.74,7.375 2.25,0.563 10 false Transmission Control ECU 4.49,6.646 4.948,6.844 0.458,0.198 10 false C33 0.344,6.708 1.635,7.042 1.292,0.333 10 false ST NO.2 1.073,7.073 2.365,7.406 1.292,0.333 10 false ST NO. 2 1.042,6.438 1.5,6.635 0.458,0.198 10 false 5 1.729,6.438 2.188,6.635 0.458,0.198 10 false 3 1.042,6.698 1.5,6.896 0.458,0.198 10 false 1 1.729,6.688 2.188,6.885 0.458,0.198 10 false 2 4.594,6.01 5.104,6.354 0.51,0.344 10 false 34 0.552,4.969 1.01,5.167 0.458,0.198 10 false STA 0.927,4.854 1.385,5.052 0.458,0.198 10 false 21 3.708,3.938 4.167,4.135 0.458,0.198 10 false 5 *2 4.51,9.094 6.354,9.406 1.844,0.313 10 false *1: for Automatic Transaxle 4.542,9.417 6.229,9.615 1.688,0.198 10 false *2: for CVT

for Manual Transaxle:
E407998E04
6.135,0.479 6.594,0.677 0.458,0.198 10 false STA 6.115,1.667 6.573,1.865 0.458,0.198 10 false STAR 5.938,1.688 6.396,1.885 0.458,0.198 10 false 9 5.885,0.479 6.344,0.677 0.458,0.198 10 false 20 6.75,0.719 7.156,0.948 0.406,0.229 10 false IC 6.76,1.677 7.156,1.927 0.396,0.25 10 false IC 6.167,1.333 6.625,1.531 0.458,0.198 10 false +B 0.844,0.604 1.302,0.802 0.458,0.198 10 false STA 0.802,1.792 1.26,1.99 0.458,0.198 10 false NSW 0.333,2.646 0.792,2.844 0.458,0.198 10 false ECM 0.844,4.458 1.302,4.656 0.458,0.198 10 false STA 0.917,3.646 1.375,3.844 0.458,0.198 10 false CLL 2.844,4.125 4.927,4.76 2.083,0.635 10 false Clutch Start Switch Assembly 0.188,5.302 2.271,5.938 2.083,0.635 10 false Engine Stop and Start ECU 1.604,5.688 3.688,6.323 2.083,0.635 10 false from Battery 1.635,6.573 2.094,6.771 0.458,0.198 10 false B 2.667,6.563 3.125,6.76 0.458,0.198 10 false SL1 5.635,2.771 7.156,3.677 1.521,0.906 10 false Certification ECU (Smart Key ECU Assembly) 5.656,2.625 6.115,2.823 0.458,0.198 10 false A15 1.24,1.667 1.698,1.865 0.458,0.198 10 false 23 1.26,0.49 1.719,0.688 0.458,0.198 10 false 30 0.344,2.469 1.583,2.688 1.24,0.219 10 false A24 2.76,3.51 3.219,3.708 0.458,0.198 10 false 2 2.833,3.99 3.292,4.188 0.458,0.198 10 false A81 0.198,5.125 0.656,5.323 0.458,0.198 10 false A34 1.25,3.51 1.708,3.708 0.458,0.198 10 false 17 1.229,4.344 1.688,4.542 0.458,0.198 10 false 21 1.333,6.344 1.792,6.542 0.458,0.198 10 false 1 3.115,6.354 3.573,6.552 0.458,0.198 10 false 2 1.281,6.563 1.74,6.76 0.458,0.198 10 false D1 3.042,6.552 3.5,6.75 0.458,0.198 10 false C43 4.188,3.521 4.646,3.719 0.458,0.198 10 false 1 1.594,7.198 3.677,7.833 2.083,0.635 10 false Starter Assembly 4.271,7.208 5.281,7.563 1.01,0.354 10 false ST NO. 1 4.281,6.135 5.292,6.49 1.01,0.354 10 false ST NO.1 4.135,6.729 4.594,6.927 0.458,0.198 10 false 1 4.885,6.76 5.344,6.958 0.458,0.198 10 false 2 4.885,6.458 5.344,6.656 0.458,0.198 10 false 5 4.125,6.458 4.583,6.656 0.458,0.198 10 false 3


w/o Stop and Start System



except Manual Transaxle:
E407999E05
5.042,2.198 5.5,2.396 0.458,0.198 10 false STA 5.031,0.563 5.49,0.76 0.458,0.198 10 false STAR 5.042,1.24 5.5,1.438 0.458,0.198 10 false STP1 5.74,3.146 6.198,3.344 0.458,0.198 10 false P 5.958,2.896 6.417,3.094 0.458,0.198 10 false 22 4.708,1.146 5.167,1.344 0.458,0.198 10 false 25 4.76,0.458 5.219,0.656 0.458,0.198 10 false 9 4.74,2.104 5.198,2.302 0.458,0.198 10 false 20 5.646,0.531 6.104,0.729 0.458,0.198 10 false IC 5.656,1.448 6.115,1.646 0.458,0.198 10 false IC 5.677,2.417 6.135,2.615 0.458,0.198 10 false IC 5.094,0.208 5.552,0.406 0.458,0.198 10 false +B 0.552,2.292 1.01,2.49 0.458,0.198 10 false STA 0.49,0.656 0.948,0.854 0.458,0.198 10 false NSW 0.542,1.219 1,1.417 0.458,0.198 10 false STP 0.073,3.031 0.531,3.229 0.458,0.198 10 false ECM 6.615,3.146 7.073,3.344 0.458,0.198 10 false P2 6.583,4.104 7.042,4.302 0.458,0.198 10 false STP 4.615,4.76 5.073,4.958 0.458,0.198 10 false STP 4.583,6.125 5.042,6.323 0.458,0.198 10 false STP 2.604,3.469 3.063,3.667 0.458,0.198 10 false B 3,3.49 3.458,3.688 0.458,0.198 10 false L 2.219,3.75 2.677,3.948 0.458,0.198 10 false P 2.198,4.042 2.656,4.24 0.458,0.198 10 false N 1.656,4.417 3,5.125 1.344,0.708 10 false Park/Neutral Position Switch Assembly 0.667,4.917 2.75,5.552 2.083,0.635 10 false from Battery 1.521,5.979 2.813,6.313 1.292,0.333 10 false ST NO.1 0.313,5.604 1.604,5.938 1.292,0.333 10 false ST NO. 1 1.156,7.396 2.448,7.729 1.292,0.333 10 false Starter Assembly 1.083,6.74 1.542,6.938 0.458,0.198 10 false B 2.229,6.948 2.688,7.146 0.458,0.198 10 false ST 5.75,4.719 7.156,5.656 1.406,0.938 10 false Shift Lock Control Unit Assembly 4.323,3.615 6.188,4.354 1.865,0.74 10 false Certification ECU (Smart Key ECU Assembly) 4.802,8.49 6.844,8.802 2.042,0.313 10 false Stop Light Switch Assembly 5.604,7.719 6.063,7.917 0.458,0.198 10 false IC 5.635,7.115 7.104,7.813 1.469,0.698 10 false from Battery 4.656,7.292 6.125,7.99 1.469,0.698 10 false STOP 5.208,7.667 5.667,7.865 0.458,0.198 10 false B 5.208,7.958 6.01,8.167 0.802,0.208 10 false L 6.125,8.167 6.583,8.365 0.458,0.198 10 false GND 4.698,2.292 5.156,2.49 0.458,0.198 10 false A15 4.688,0.656 5.146,0.854 0.458,0.198 10 false A15 4.708,1.333 5.167,1.531 0.458,0.198 10 false M7 5.927,3.125 6.396,3.323 0.469,0.198 10 false G54 0.927,0.563 1.385,0.76 0.458,0.198 10 false 23 0.927,2.156 1.385,2.354 0.458,0.198 10 false 30 0.948,1.229 1.406,1.427 0.458,0.198 10 false 21 0.063,2.833 1.302,3.052 1.24,0.219 10 false A24 0.271,1.448 0.729,1.646 0.458,0.198 10 false IC 2.74,3.229 3.198,3.427 0.458,0.198 10 false 4 3.313,3.771 3.771,3.969 0.458,0.198 10 false 9 *1 1.656,4.24 2.115,4.438 0.458,0.198 10 false C31 4.802,8.313 5.26,8.51 0.458,0.198 10 false A40 1.333,5.604 1.792,5.802 0.458,0.198 10 false 1 2.031,5.594 2.49,5.792 0.458,0.198 10 false 2 2.021,5.281 2.479,5.479 0.458,0.198 10 false 3 1.354,5.323 1.896,5.542 0.542,0.219 10 false 5 0.76,6.531 1.219,6.729 0.458,0.198 10 false 1 0.708,6.74 1.167,6.938 0.458,0.198 10 false D2 2.531,6.927 2.99,7.125 0.458,0.198 10 false C42 5.01,7.969 5.469,8.167 0.458,0.198 10 false 3 5.021,7.563 5.479,7.76 0.458,0.198 10 false 7 6.531,8.052 6.99,8.25 0.458,0.198 10 false 2 2.594,6.75 3.052,6.948 0.458,0.198 10 false 1 6.417,3.031 6.875,3.229 0.458,0.198 10 false 3 6.396,4.042 6.854,4.24 0.458,0.198 10 false 4 5.76,4.521 6.219,4.719 0.458,0.198 10 false G26 4.354,4.656 4.813,4.854 0.458,0.198 10 false 41 4.302,5.385 6.708,6.25 2.406,0.865 10 false Skid Control ECU Assembly 4.281,5.219 4.74,5.417 0.458,0.198 10 false A39 4.354,6.646 5.823,7.344 1.469,0.698 10 false C33 4.354,6.802 6.417,7.51 2.063,0.708 10 false Transmission Control ECU 4.333,6.042 4.792,6.24 0.458,0.198 10 false 34 3.313,3.938 3.771,4.135 0.458,0.198 10 false 5 *2 4.208,9.469 5.896,9.667 1.688,0.198 10 false *2: for CVT 4.208,9.198 6.167,9.604 1.958,0.406 10 false *1: for Automatic Transaxle

for Manual Transaxle:
E408000E04
6.104,0.635 6.563,0.833 0.458,0.198 10 false STA 6.094,1.813 6.552,2.01 0.458,0.198 10 false STAR 5.906,1.802 6.365,2 0.458,0.198 10 false 9 5.865,0.615 6.323,0.813 0.458,0.198 10 false 20 6.729,0.875 7.146,1.188 0.417,0.313 10 false IC 6.719,1.844 7.156,2.073 0.438,0.229 10 false IC 6.146,1.49 6.604,1.688 0.458,0.198 10 false +B 0.802,0.729 1.26,0.927 0.458,0.198 10 false STA 0.76,1.917 1.219,2.115 0.458,0.198 10 false NSW 0.365,2.792 0.823,2.99 0.458,0.198 10 false ECM 2.698,3.469 4.781,4.104 2.083,0.635 10 false Clutch Start Switch Assembly 1.552,4.094 3.635,4.729 2.083,0.635 10 false from Battery 4.208,5.615 5.5,5.948 1.292,0.333 10 false ST NO. 1 1.594,5.594 2.885,5.927 1.292,0.333 10 false Starter Assembly 1.583,4.969 2.042,5.167 0.458,0.198 10 false B 2.719,4.958 3.177,5.156 0.458,0.198 10 false ST 5.615,2.854 7.146,3.792 1.531,0.938 10 false Certification ECU (Smart Key ECU Assembly) 5.635,2.708 6.094,2.906 0.458,0.198 10 false A15 1.198,1.802 1.656,2 0.458,0.198 10 false 23 1.219,0.615 1.677,0.813 0.458,0.198 10 false 30 0.354,2.583 1.594,2.802 1.24,0.219 10 false A24 4.135,2.823 4.594,3.021 0.458,0.198 10 false 1 2.708,2.823 3.167,3.021 0.458,0.198 10 false 2 2.708,3.281 3.167,3.479 0.458,0.198 10 false A81 1.292,4.76 1.75,4.958 0.458,0.198 10 false 1 1.25,4.969 1.708,5.167 0.458,0.198 10 false D2 3,4.958 3.458,5.156 0.458,0.198 10 false C42 3.083,4.771 3.542,4.969 0.458,0.198 10 false 1 4.24,4.542 5.531,4.875 1.292,0.333 10 false ST NO.1 4.094,5.146 4.552,5.344 0.458,0.198 10 false 1 4.833,5.167 5.292,5.365 0.458,0.198 10 false 2 4.104,4.854 4.563,5.052 0.458,0.198 10 false 3 4.844,4.865 5.302,5.063 0.458,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

If the entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>CUSTOMIZE PARAMETERS

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to the Service Bulletin.

·

After completing repairs, confirm that the problem does not recur.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Proceed to
for Manual Transaxle
except Manual Transaxle



for Manual Transaxle

2.CHECK ENGINE SWITCH CONDITION

except Manual Transaxle

23.CHECK ENGINE SWITCH CONDITION
2.CHECK ENGINE SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

With the clutch pedal released, check that pressing the engine switch causes the power source mode to change.


Result:
Result Proceed to
Power source mode changes: Off → on (ACC) → on (IG) → off A
Power source mode does not change to on (ACC) or on (IG) B
Power source mode changes to on (IG) but not to on (ACC) C
Power source mode changes to on (ACC) but not to on (IG) D



A

3.READ VALUE USING GTS (Neutral SW/Clutch SW)

B

GO TO ENTRY AND START SYSTEM (for Start Function) (Power Source Mode does not Change to ON (IG and ACC))

C

GO TO ENTRY AND START SYSTEM (for Start Function) (Power Source Mode does not Change to ON (ACC))

D

GO TO ENTRY AND START SYSTEM (for Start Function) (Power Source Mode does not Change to ON (IG))

3.READ VALUE USING GTS (Neutral SW/Clutch SW)
a.

Enter the following menus: Body Electrical / Power Source Control / Data List.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW State of clutch pedal ON or OFF ON: Clutch pedal depressed
OFF: Clutch pedal released
·

Use this item to determine whether the clutch position switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".


Body Electrical > Power Source Control > Data List
Tester Display
Neutral SW/ Clutch SW
50003 223 6

OK:

The GTS display changes correctly in response to the clutch pedal operation.


Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

NG

15.READ VALUE USING GTS (Neutral SW/Clutch SW)
4.READ VALUE USING GTS (STARTER REQUEST SIGNAL)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Request Signal Engine start request signal status OFF or ON OFF: The engine switch is not pressed
ON: With the clutch pedal depressed, the engine switch is pressed and held
·

When the engine cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Starter Request Signal
50003 223 12
NOTICE:

Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the engine switch.


OK:

The GTS display changes correctly in response to the engine switch operation.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (STARTER SW)

NG

13.CHECK STEERING LOCK
5.READ VALUE USING GTS (STARTER SW)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Enter the following menus: Body Electrical / Starting Control / Data List.


c.

Read the Data List while pressing the engine switch with the clutch pedal depressed according to the display on the GTS.

Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter SW Starter operation request OFF or ON OFF: Starter operation not requested
ON: Starter operation requested
When OFF is displayed, the engine will not crank.
Body Electrical > Starting Control > Data List
Tester Display
Starter SW
50003 221 1
OK:

The GTS display changes.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - POWER SUPPLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - POWER SUPPLY)
a.
C378519C06
0.156,0.125 0.521,0.469 0.365,0.344 10 false *a
*a No. 1 Engine Room Relay Block
(ST No. 1 Relay Installation Terminal)


Remove the ST NO. 1 relay.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ST NO. 1 relay installation terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY AND BODY GROUND)
a.

Disconnect the A15 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 1 relay installation terminal 2 - A15-20 (STA) Always Below 1 Ω
ST NO. 1 relay installation terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.INSPECT ST NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT ST NO. 1 RELAY
a.

Remove the ST NO. 1 relay.


b.

Inspect the ST NO. 1 relay.

Click hereEngine / Hybrid System>M20A-FKS (STARTING)>RELAY>INSPECTION


Result:
Proceed to
OK (w/ Stop and Start System)
OK (w/o Stop and Start System)
NG



OK (w/ Stop and Start System)

9.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)

OK (w/o Stop and Start System)

11.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)

NG

REPLACE ST NO. 1 RELAY

9.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)
a.

Disconnect the C43 starter assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 1 relay installation terminal 3 - C43-2 (SL1) Always Below 1 Ω
ST NO. 1 relay installation terminal 3 or C43-2 (SL1) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - POWER SUPPLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - POWER SUPPLY)
a.
C378520C19
2.083,0.104 2.469,0.313 0.385,0.208 0.344,0.156 0.656,0.354 0.313,0.198 10 false *a 2.177,0.135 2.49,0.333 0.313,0.198 10 false D1
*a Front view of wire harness connector
(to Starter Assembly)


Disconnect the starter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D1-1 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)
a.

Disconnect the C42 starter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 1 relay installation terminal 3 - C42-1 (ST) Always Below 1 Ω
ST NO. 1 relay installation terminal 3 or C42-1 (ST) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - POWER SUPPLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - POWER SUPPLY)
a.
C378520C20
2.083,0.104 2.469,0.313 0.385,0.208 0.344,0.156 0.656,0.354 0.313,0.198 10 false *a 2.188,0.125 2.5,0.323 0.313,0.198 10 false D2
*a Front view of wire harness connector
(to Starter Assembly)


Disconnect the starter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D2-1 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK STEERING LOCK
a.

Check that the steering unlocks when the engine switch is turned on (ACC).

OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

14.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET)

NG

GO TO ENTRY AND START SYSTEM (for Start Function) (Unable to Unlock Steering Wheel (Engine cannot Start))

14.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Press the engine switch with the clutch pedal released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).

OK:

The security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).


HINT:

The immobiliser function can be determined to be operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

GO TO ENTRY AND START SYSTEM (for Start Function) (Immobiliser System does not Operate Properly)

15.READ VALUE USING GTS (Neutral SW/Clutch SW)
a.

Disconnect the A24 ECM connector.


b.

Enter the following menus: Body Electrical / Power Source Control / Data List.


c.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW State of clutch pedal ON or OFF ON: Clutch pedal depressed
OFF: Clutch pedal released
·

Use this item to determine whether the clutch position switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".


Body Electrical > Power Source Control > Data List
Tester Display
Neutral SW/ Clutch SW
50003 223 6

OK:

The GTS display changes correctly in response to the clutch pedal operation.


Result:
Proceed to
OK
NG (w/ Stop and Start System)
NG (w/o Stop and Start System)



OK

NG (w/ Stop and Start System)

16.READ VALUE USING GTS (Neutral SW/Clutch SW)

NG (w/o Stop and Start System)

17.INSPECT CLUTCH START SWITCH ASSEMBLY
16.READ VALUE USING GTS (Neutral SW/Clutch SW)
a.

Disconnect the A34 engine stop and start ECU connector.


b.

Enter the following menus: Body Electrical / Power Source Control / Data List.


c.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW State of clutch pedal ON or OFF ON: Clutch pedal depressed
OFF: Clutch pedal released
·

Use this item to determine whether the clutch position switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".


Body Electrical > Power Source Control > Data List
Tester Display
Neutral SW/ Clutch SW
50003 223 6

OK:

The GTS display changes correctly in response to the clutch pedal operation.


Result:
Proceed to
OK
NG



OK

NG

17.INSPECT CLUTCH START SWITCH ASSEMBLY
17.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Remove the clutch start switch assembly.

for LHD:

Click hereDrivetrain>CLUTCH>CLUTCH START SWITCH (for LHD)>REMOVAL

for RHD:

Click hereDrivetrain>CLUTCH>CLUTCH START SWITCH (for RHD)>REMOVAL


b.

Inspect the clutch start switch assembly.

for LHD:

Click hereDrivetrain>CLUTCH>CLUTCH START SWITCH (for LHD)>INSPECTION

for RHD:

Click hereDrivetrain>CLUTCH>CLUTCH START SWITCH (for RHD)>INSPECTION


Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the A15 certification ECU (smart key ECU assembly) connector.


b.

Remove the ST NO. 1 relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A15-9 (STAR) - A81-2 Always Below 1 Ω
A15-20 (STA) - A81-1 Always Below 1 Ω
A15-9 (STAR) or A81-2 - Other terminals and body ground Always 10 kΩ or higher
A15-20 (STA) or A81-1 - Other terminals and body ground Always 10 kΩ or higher



d.

Connect the A15 certification ECU (smart key ECU assembly) connector.


e.

Connect the A81 clutch start switch assembly connector.


f.

Install the ST NO. 1 relay


Result:
Proceed to
OK
NG



OK

19.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL STAR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL STAR)
a.
B424432C85
1.458,0.073 1.875,0.323 0.417,0.25 0.781,1.438 0.917,1.438 0.917,1.438 1.615,0.979 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.531,0.135 1.844,0.333 0.313,0.198 10 false A15 0.365,1.354 0.896,1.542 0.531,0.188 10 false STAR
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A15-9 (STAR) - Body ground Engine switch pressed and held with clutch pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

20.INSPECT ST NO. 1 RELAY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

20.INSPECT ST NO. 1 RELAY
a.

Remove the ST NO. 1 relay.


b.

Inspect the ST NO. 1 relay.

Click hereEngine / Hybrid System>M20A-FKS (STARTING)>RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)

NG

REPLACE ST NO. 1 RELAY

21.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)
a.
C378519C05
0.156,0.125 0.521,0.469 0.365,0.344 10 false *a
*a No. 1 Engine Room Relay Block
(ST No. 1 Relay Installation Terminal)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ST NO. 1 relay installation terminal 2 - Body ground Engine switch pressed and held with clutch pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

22.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
a.
C378519C06
0.156,0.125 0.521,0.469 0.365,0.344 10 false *a
*a No. 1 Engine Room Relay Block
(ST No. 1 Relay Installation Terminal)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 1 relay installation terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK ENGINE SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift state park (P).


c.

With the brake pedal released, check that pressing the engine switch causes the power source mode to change.


Result:
Result Proceed to
Power source mode changes: Off → on (ACC) → on (IG) → off A
Power source mode does not change to on (ACC) or on (IG) B
Power source mode changes to on (IG) but not to on (ACC) C
Power source mode changes to on (ACC) but not to on (IG) D



A

24.READ VALUE USING GTS (STOP LIGHT SWITCH1)

B

GO TO ENTRY AND START SYSTEM (for Start Function) (Power Source Mode does not Change to ON (IG and ACC))

C

GO TO ENTRY AND START SYSTEM (for Start Function) (Power Source Mode does not Change to ON (ACC))

D

GO TO ENTRY AND START SYSTEM (for Start Function) (Power Source Mode does not Change to ON (IG))

24.READ VALUE USING GTS (STOP LIGHT SWITCH1)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine if the stop light switch assembly is malfunctioning.

·

The engine cannot be started when this item is OFF.

·

If the stop light switch assembly is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

The GTS display changes correctly in response to the brake pedal operation.



Result:
Proceed to
OK
NG



OK

25.READ VALUE USING GTS (SHIFT P SIGNAL)

NG

55.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SUPPLY AND BODY GROUND)
25.READ VALUE USING GTS (SHIFT P SIGNAL)
a.

Enter the following menus: Body Electrical / Power Source Control / Data List.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P Signal State of brake pedal ON or OFF ON: Shift state park (P)
OFF: Shift state not park (P)
·

Use this item to determine if the shift position switch is malfunctioning.

·

The engine cannot be started when this item is OFF.


Body Electrical > Power Source Control > Data List
Tester Display
Shift P Signal
50003 223 1
OK:

The GTS display changes correctly in response to the shift state.



Result:
Proceed to
OK
NG



OK

26.READ VALUE USING GTS (Neutral SW/Clutch SW, SHIFT POSITION P OR N)

NG

52.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY (OUTPUT TO CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
26.READ VALUE USING GTS (Neutral SW/Clutch SW, SHIFT POSITION P OR N)
a.

Enter the following menus: Body Electrical / Power Source Control / Data List.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW Shift position (P, N) ON or OFF ON: Shift state park (P) or (N)
OFF: Shift state not park (P) or (N)
·

Use this item to determine whether the park/neutral position switch assembly is malfunctioning.

·

When the engine cannot be started due to a park/neutral position switch assembly malfunction, OFF is displayed.


Body Electrical > Power Source Control > Data List
Tester Display
Neutral SW/ Clutch SW
50003 223 6

c.

Enter the following menus: Body Electrical / Starting Control / Data List.


d.

Read the Data List according to the display on the GTS.

Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift Position P or N Park/Neutral position switch status OFF or ON OFF: Shift state not park (P) or (N)
ON: Shift state park (P) or (N)
When OFF is displayed, the engine will not crank.
Body Electrical > Starting Control > Data List
Tester Display
Shift Position P or N
50003 221 2

OK:

The GTS display changes correctly in response to the shift state.


Result:
Proceed to
OK
NG



OK

27.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

NG

44.READ VALUE USING GTS (Neutral SW/Clutch SW, SHIFT POSITION P OR N)
27.READ VALUE USING GTS (STARTER REQUEST SIGNAL)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Request Signal Engine start request signal status OFF or ON OFF: The engine switch is not pressed
ON: With the shift state park (P) and the brake pedal depressed, the engine switch is pressed and held
·

When the engine cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Starter Request Signal
50003 223 12
NOTICE:

Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the engine switch.


OK:

The GTS display changes correctly in response to the engine switch operation.



Result:
Proceed to
OK
NG



OK

28.READ VALUE USING GTS (STARTER SW)

NG

42.CHECK STEERING LOCK
28.READ VALUE USING GTS (STARTER SW)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Shift state park (P).


c.

Enter the following menus: Body Electrical / Starting Control / Data List.


d.

Read the Data List while pressing the engine switch with the brake pedal depressed according to the display on the GTS.

Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter SW Starter operation request OFF or ON OFF: Starter operation not requested
ON: Starter operation requested
When OFF is displayed, the engine will not crank.
Body Electrical > Starting Control > Data List
Tester Display
Starter SW
50003 221 1
OK:

The GTS display changes.



Result:
Proceed to
OK
NG



OK

29.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - POWER SUPPLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

29.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - POWER SUPPLY)
a.
C378519C06
0.156,0.125 0.521,0.469 0.365,0.344 10 false *a
*a No. 1 Engine Room Relay Block
(ST No. 1 Relay Installation Terminal)


Remove the ST NO. 1 relay.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ST NO. 1 relay installation terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

30.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY AND BODY GROUND)
a.

Disconnect the A15 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 1 relay installation terminal 2 - A15-20 (STA) Always Below 1 Ω
ST NO. 1 relay installation terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

31.INSPECT ST NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

31.INSPECT ST NO. 1 RELAY
a.

Remove the ST NO. 1 relay.


b.

Inspect the ST NO. 1 relay.

for A25A-FKS:

Click hereEngine / Hybrid System>A25A-FKS (STARTING)>RELAY>INSPECTION

for M20A-FKS:

Click hereEngine / Hybrid System>M20A-FKS (STARTING)>RELAY>INSPECTION


Result:
Proceed to
OK (w/ Stop and Start System)
OK (w/o Stop and Start System)
NG



OK (w/ Stop and Start System)

32.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)

OK (w/o Stop and Start System)

40.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)

NG

REPLACE ST NO. 1 RELAY

32.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)
a.

Disconnect the C43 starter assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 1 relay installation terminal 3 - C43-2 (SL1) Always Below 1 Ω
ST NO. 1 relay installation terminal 3 or C43-2 (SL1) - Other terminals and body ground Always 10 kΩ or higher



c.

Connect the C43 starter assembly connectors.


Result:
Proceed to
OK
NG



OK

33.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

33.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - BODY GROUND)
a.
C378519C03
0.156,0.125 0.521,0.469 0.365,0.344 10 false *a
*a No. 1 Engine Room Relay Block
(ST No. 2 Relay Installation Terminal)


Remove the ST NO. 2 relay.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ST NO. 2 relay installation terminal 2 - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

34.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - POWER SUPPLY AND BODY GROUND)

NG

38.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - ENGINE STOP AND START ECU)
34.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - POWER SUPPLY AND BODY GROUND)
a.
C378519C03
0.156,0.125 0.521,0.469 0.365,0.344 10 false *a
*a No. 1 Engine Room Relay Block
(ST No. 2 Relay Installation Terminal)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 2 relay installation terminal 1 - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ST NO. 2 relay installation terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

35.INSPECT ST NO. 2 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

35.INSPECT ST NO. 2 RELAY
a.

Remove the ST NO. 2 relay.


b.

Inspect the ST NO. 2 relay.

Click hereEngine / Hybrid System>M20A-FKS (STARTING)>RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

36.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - STARTER ASSEMBLY)

NG

REPLACE ST NO. 2 RELAY

36.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - STARTER ASSEMBLY)
a.

Disconnect the C43 starter assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 2 relay installation terminal 3 - C43-1 (SL2) Always Below 1 Ω
ST NO. 2 relay installation terminal 3 or C43-1 (SL2) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

37.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - POWER SUPPLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

37.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - POWER SUPPLY)
a.
C378520C21
2.083,0.104 2.469,0.313 0.385,0.208 0.344,0.156 0.656,0.354 0.313,0.198 10 false *a 2.188,0.125 2.5,0.323 0.313,0.198 10 false D1
*a Front view of wire harness connector
(to Starter Assembly)


Disconnect the starter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D1-1 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

38.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - ENGINE STOP AND START ECU)
a.

Disconnect the A34 engine stop and start ECU connector.


b.

Disconnect the A24 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 2 relay installation terminal 2 - A34-23 (STA2) Always Below 1 Ω
ST NO. 2 relay installation terminal 2 - A24-30 (STA) Always Below 1 Ω
ST NO. 2 relay installation terminal 2 or A34-23 (STA2) - Other terminals and body ground Always 10 kΩ or higher
ST NO. 2 relay installation terminal 2 or A24-30 (STA) - Other terminals and body ground Always 10 kΩ or higher



d.

Connect the A34 engine stop and start ECU connector.


Result:
Proceed to
OK
NG



OK

39.CHECK ENGINE STOP AND START ECU (TERMINAL STA2)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

39.CHECK ENGINE STOP AND START ECU (TERMINAL STA2)
a.

Install the ST NO. 2 relay.

A397704C61
3.188,0.083 3.604,0.323 0.417,0.24 2.781,1.469 3.135,0.802 true 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a 3.271,0.125 3.667,0.323 0.396,0.198 10 false A34 2.594,1.5 3.125,1.698 0.531,0.198 10 false STA2
*a Component without harness connected
(Engine Stop and Start ECU)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-23 (STA2) - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

NG

40.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)
a.

Disconnect the C42 starter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 1 relay installation terminal 3 - C42-1 (ST) Always Below 1 Ω
ST NO. 1 relay installation terminal 3 or C42-1 (ST) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

41.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - POWER SUPPLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

41.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - POWER SUPPLY)
a.
C378520C22
2.083,0.104 2.469,0.313 0.385,0.208 0.344,0.156 0.656,0.354 0.313,0.198 10 false *a 2.188,0.125 2.5,0.323 0.313,0.198 10 false D2
*a Front view of wire harness connector
(to Starter Assembly)


Disconnect the starter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D2-1 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

42.CHECK STEERING LOCK
a.

Check that the steering unlocks when the engine switch is turned on (ACC).

OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

43.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET)

NG

GO TO ENTRY AND START SYSTEM (for Start Function) (Unable to Unlock Steering Wheel (Engine cannot Start))

43.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Shift state park (P).


c.

Press the engine switch with the brake pedal released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).

OK:

The security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).


HINT:

The immobiliser function can be determined to be operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

GO TO ENTRY AND START SYSTEM (for Start Function) (Immobiliser System does not Operate Properly)

44.READ VALUE USING GTS (Neutral SW/Clutch SW, SHIFT POSITION P OR N)
a.

Disconnect the A24 ECM connector.


b.

Enter the following menus: Body Electrical / Power Source Control / Data List.


c.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW Shift position (P, N) ON or OFF ON: Shift state park (P) or (N)
OFF: Shift state not park (P) or (N)
·

Use this item to determine whether the park/neutral position switch assembly is malfunctioning.

·

When the engine cannot be started due to a park/neutral position switch assembly malfunction, OFF is displayed.


Body Electrical > Power Source Control > Data List
Tester Display
Neutral SW/ Clutch SW
50003 223 6

d.

Enter the following menus: Body Electrical / Starting Control / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift Position P or N Park/Neutral position switch status OFF or ON OFF: Shift state not park (P) or (N)
ON: Shift state park (P) or (N)
When OFF is displayed, the engine will not crank.
Body Electrical > Starting Control > Data List
Tester Display
Shift Position P or N
50003 221 2

OK:

The GTS display changes correctly in response to the shift state.


Result:
Proceed to
OK
NG (w/ Stop and Start System)
NG (w/o Stop and Start System)



OK

NG (w/ Stop and Start System)

45.READ VALUE USING GTS (Neutral SW/Clutch SW, SHIFT POSITION P OR N)

NG (w/o Stop and Start System)

46.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
45.READ VALUE USING GTS (Neutral SW/Clutch SW, SHIFT POSITION P OR N)
a.

Disconnect the A34 engine stop and start ECU connector.


b.

Enter the following menus: Body Electrical / Power Source Control / Data List.


c.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW Shift position (P, N) ON or OFF ON: Shift state park (P) or (N)
OFF: Shift state not park (P) or (N)
·

Use this item to determine whether the park/neutral position switch assembly is malfunctioning.

·

When the engine cannot be started due to a park/neutral position switch assembly malfunction, OFF is displayed.


Body Electrical > Power Source Control > Data List
Tester Display
Neutral SW/ Clutch SW
50003 223 6

d.

Enter the following menus: Body Electrical / Starting Control / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift Position P or N Park/Neutral position switch status OFF or ON OFF: Shift state not park (P) or (N)
ON: Shift state park (P) or (N)
When OFF is displayed, the engine will not crank.
Body Electrical > Starting Control > Data List
Tester Display
Shift Position P or N
50003 221 2

OK:

The GTS display changes correctly in response to the shift state.


Result:
Proceed to
OK
NG



OK

NG

46.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
46.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

OK

47.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

47.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the A15 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the C31 park/neutral position switch assembly connector.


c.

Remove the ST NO. 1 relay.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Automatic Transaxle:
Tester Connection Condition Specified Condition
A15-9 (STAR) - C31-4 (B) Always Below 1 Ω
A15-20 (STA) - C31-9 (L) Always Below 1 Ω
A15-9 (STAR) or C31-4 (B) - Other terminals and body ground Always 10 kΩ or higher
A15-20 (STA) or C31-9 (L) - Other terminals and body ground Always 10 kΩ or higher

for CVT:
Tester Connection Condition Specified Condition
A15-9 (STAR) - C31-4 (B) Always Below 1 Ω
A15-20 (STA) - C31-5 (L) Always Below 1 Ω
A15-9 (STAR) or C31-4 (B) - Other terminals and body ground Always 10 kΩ or higher
A15-20 (STA) or C31-5 (L) - Other terminals and body ground Always 10 kΩ or higher



e.

Connect the A15 certification ECU (smart key ECU assembly) connector.


f.

Connect the C31 park/neutral position switch assembly connector.


g.

Install the ST NO. 1 relay


Result:
Proceed to
OK
NG



OK

48.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL STAR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

48.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL STAR)
a.
B424432C85
1.458,0.073 1.875,0.323 0.417,0.25 0.781,1.438 0.917,1.438 0.917,1.438 1.615,0.979 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.531,0.135 1.844,0.333 0.313,0.198 10 false A15 0.365,1.354 0.896,1.542 0.531,0.188 10 false STAR
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A15-9 (STAR) - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

49.INSPECT ST NO. 1 RELAY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

49.INSPECT ST NO. 1 RELAY
a.

Remove the ST NO. 1 relay.


b.

Inspect the ST NO. 1 relay.

for A25A-FKS:

Click hereEngine / Hybrid System>A25A-FKS (STARTING)>RELAY>INSPECTION

for M20A-FKS:

Click hereEngine / Hybrid System>M20A-FKS (STARTING)>RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

50.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)

NG

REPLACE ST NO. 1 RELAY

50.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)
a.
C378519C05
0.156,0.125 0.521,0.469 0.365,0.344 10 false *a
*a No. 1 Engine Room Relay Block
(ST No. 1 Relay Installation Terminal)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ST NO. 1 relay installation terminal 2 - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

51.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

51.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
a.
C378519C06
0.156,0.125 0.521,0.469 0.365,0.344 10 false *a
*a No. 1 Engine Room Relay Block
(ST No. 1 Relay Installation Terminal)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 1 relay installation terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

52.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY (OUTPUT TO CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.
B510755C08
1.531,0.073 1.948,0.333 0.417,0.26 2.188,1.917 2.063,1.917 2.063,1.917 1.823,1.115 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 1.635,0.135 1.948,0.333 0.313,0.198 10 false G54 2.26,1.865 2.573,2.063 0.313,0.198 10 false P
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G54-22 (P) - Other terminals and body ground Shift state park (P) → Shift state not park (P) 9 V or higher → 2.76 V or less



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

53.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT LOCK CONTROL UNIT ASSEMBLY)
53.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.

Disconnect the G54 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G26 shift lock control unit assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-22 (P) - G26-3 (P2) Always Below 1 Ω
G54-22 (P) or G26-3 (P2) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

54.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

54.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
a.
B498244C40
1.604,0.115 1.969,0.354 0.365,0.24 2.406,1.948 2.156,1.948 2.156,1.948 1.823,1.104 false 1.667,0.167 2.01,0.365 0.344,0.198 10 false G54 2.469,1.896 3.063,2.094 0.594,0.198 10 false P 0.146,0.125 0.74,0.323 0.594,0.198 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Reconnect the certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G54-22 (P) - Other terminals and body ground Shift state park (P) 9 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

55.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SUPPLY AND BODY GROUND)
a.
E409581C03
1.458,0.094 1.958,0.344 0.5,0.25 0.948,1.917 1.115,1.917 1.115,1.917 1.281,1.375 true 2.625,1.917 2.458,1.917 2.458,1.917 2.313,1.344 true 0.115,0.125 0.427,0.281 0.313,0.156 10 false *a 1.594,0.146 1.906,0.302 0.313,0.156 10 false A40 2.698,1.833 3.01,1.99 0.313,0.156 10 false B 0.604,1.833 1.052,2.042 0.448,0.208 10 false GND
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-7 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

56.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

56.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

57.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

57.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the M7 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A24 ECM connector.


c.

Disconnect the A39 skid control ECU assembly connector.


d.

Disconnect the G26 shift lock control unit assembly connector.


e.

Disconnect the C33 transmission control ECU connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M7-25 (STP1) - A40-3 (L) Always Below 1 Ω
M7-25 (STP1) or A40-3 (L) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR