Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER OIL SEAL (for Torque Vectoring Differential) › 2018.10–2020.08
RM3620E _52 Drivetrain _076176 AXLE AND DIFFERENTIAL _0417252 REAR DIFFERENTIAL CARRIER OIL SEAL(for Torque Vectoring Differential) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER OIL SEAL(for Torque Vectoring Differential)  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during torque vectoring differential carrier assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Electro magnetic control coupling sub-assembly
·

ECU data save

·

ECU data initialization

·

ECU data write


Dynamic torque vectoring AWD system (Click here)
Rear electro magnetic control clutch sub-assembly (rear differential carrier assembly) Disconnect system function check
Rear wheel alignment adjustment
1.

Perform "Reset Memory".

2.

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (for Gasoline model) (Click here)
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT)(w/ Headlight ECU without AFS) (Click here)
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


w/ Canister Pump Module:(Click here)
w/o Canister Pump Module:(Click here)

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
System Name See Procedure
Vehicle enrolled in Toyota Audio Multimedia system or safety connect system 6 minutes
Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system 1 minute


PROCEDURE

Hide 41110 1.REMOVE TORQUE VECTORING DIFFERENTIAL CARRIER ASSEMBLY

Hide 5.INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

Hide 41201C 9.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL (for Front Side)

a.
C418045C01
1.521,0.677 2.042,0.125 2.042,0.125 2.292,0.125 false 2.885,2.177 2.885,0.979 2.885,0.979 3.052,0.979 true 2.375,0.042 2.833,0.271 0.458,0.229 10 false SST 3.125,0.885 3.427,1.094 0.302,0.208 10 false *1
*1 Rear Differential Carrier Oil Seal


Using SST, remove the rear differential carrier oil seal from the rear differential carrier assembly.

SST
09308-00010  

NOTICE:

Do not damage the rear differential carrier oil seal press-fit surface.



b.
C418033

Remove the spacer.


c.
C418034C01
2.146,1.385 2.615,0.542 2.615,0.542 2.781,0.542 true 2.167,3.25 2.417,2.833 2.417,2.833 2.583,2.833 true 2.667,2.76 3.063,3.083 0.396,0.323 10 false SST 2.823,0.458 3.146,0.646 0.323,0.188 10 false *1
*1 Rear Drive Pinion Bearing (Inner Race)


Using SST, remove the rear drive pinion bearing (inner race).

SST
09556-40010  


d.
C418035

Remove the rear differential pinion bearing spacer.


e.

Using SST, remove the rear drive pinion bearing (outer race).

SST
09950-40011  (09951-04010, 09952-04010, 09953-04010, 09954-04010, 09957-04010)
09506-42030  
09955-04160  

C418036C01
5.99,1.406 6.271,1.198 6.271,1.198 6.438,1.198 true 1.792,1.802 2.208,1.802 true 6.49,1.135 6.802,1.292 0.313,0.156 10 false *1 3.323,0.417 3.635,0.573 0.313,0.156 10 false *a 3.302,1.635 3.615,1.792 0.313,0.156 10 false *b 2.26,1.698 2.74,1.906 0.479,0.208 10 false SST
*1 Rear Drive Pinion Bearing (Outer Race) - -
*a Turn *b Hold



Hide 41201C 10.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL (for Front Side)

a.
C418037C01
2.188,1.677 2.604,1.677 true 1.844,3.313 2.26,3.313 true 2.365,3.24 2.948,3.656 0.583,0.417 10 false SST 2.677,1.604 3.042,1.823 0.365,0.219 10 false *1
*1 Rear Drive Pinion Bearing (Outer Race)


Using SST and a press, install the rear drive pinion bearing (outer race).

SST
09506-42010  


b.
C418035

Install a new rear differential pinion bearing spacer.


c.

Temporarily install the rear drive pinion companion flange sub-assembly.


d.
C418038C01
1.771,1.729 1.771,2.427 1.771,2.427 2.813,2.427 true 2.156,1.854 2.156,2.427 true 2.958,0.583 3.271,0.74 0.313,0.156 10 false *a 0.531,1.76 0.844,1.917 0.313,0.156 10 false *b 2.906,2.344 3.219,2.573 0.313,0.229 10 false SST
*a Turn
*b Hold


Using SST, install the rear drive pinion bearing (inner race).

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)


e.
C418032C01
1.802,1.729 1.802,2.333 1.802,2.333 2.833,2.333 true 2.125,1.833 2.125,2.333 true 2.521,1 2.833,1.156 0.313,0.156 10 false *a 0.854,0.51 1.167,0.667 0.313,0.156 10 false *b 2.875,2.26 3.302,2.479 0.427,0.219 10 false SST
*a Turn
*b Hold


Using SST, remove the rear drive pinion companion flange sub-assembly.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)


f.
C418033

install the spacer.


g.

Apply a small amount of MP grease to the lip of a new rear differential carrier oil seal.


h.
C418039C01
1.281,1.063 1.5,0.708 1.5,0.708 1.667,0.708 true 1.75,2.667 2.583,2.667 false 1.917,3.083 2.333,3.083 2.333,3.083 2.333,2.833 false 1.917,2.917 2.333,2.917 2.333,2.917 2.333,2.667 false 2.667,2.583 3.052,2.76 0.385,0.177 10 false SST 0.198,0.865 0.417,1.094 0.219,0.229 10 true (A) 1.708,0.635 2.021,0.792 0.313,0.156 10 false *1
*1 Rear Differential Carrier Oil Seal


Using SST, install a new rear differential carrier oil seal to the rear differential carrier assembly.

SST
09554-42010  
09950-60021  (09951-01030)
09950-70010  (09951-07100)

Drive in depth (A):

5.7 to 6.3 mm (0.224 to 0.248 in.)


NOTICE:

Do not damage the rear differential carrier oil seal press-fit surface.


HINT:
C418050N01
2.677,1 2.885,1.208 0.208,0.208 10 false A

Press using the A surface.



Hide 41204 11.INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY