Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › FUSE BOX (for LITHIUM-ION BATTERY) › 2020.05–2020.08
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0425016 FUSE BOX(for LITHIUM-ION BATTERY) A

HYBRID / BATTERY CONTROL  FUSE BOX(for LITHIUM-ION BATTERY)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during hybrid battery terminal block removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Reset back door close position Power back door system (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of hybrid battery terminal block High voltage fuse accumulated load history reset DTCs are stored for 2WD:(Click here)
for 4WD/AWD:(Click here)
Replacement of HV battery junction block assembly Current sensor offset learning (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.


·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 82111 2.DISCONNECT ENGINE ROOM MAIN WIRE

Hide 82111 6.CONNECT ENGINE ROOM MAIN WIRE

Hide 7.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 8.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 67918E 9.REMOVE REAR DOOR SCUFF PLATE LH

Hide 58467H 10.REMOVE NO. 3 BATTERY SERVICE COVER BOARD

Hide 67917C 11.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 58466J 12.REMOVE NO. 2 BATTERY SERVICE COVER BOARD

Hide 58464D 13.REMOVE BATTERY SERVICE COVER BOARD

Hide 71033 14.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide G92Z0 18.REMOVE HV BATTERY JUNCTION BLOCK ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A462101

Disengage the 2 claws and open the wiring harness protector.


b.
A462102

Disconnect the HV battery junction block assembly connector.

NOTICE:

Insulate the disconnected high-voltage connector with insulating tape.



c.

Disconnect the hybrid battery terminal block connector.

NOTICE:

Insulate the disconnected high-voltage connector with insulating tape.



d.
A462103

Remove the bolt and electric vehicle battery plug assembly from the HV battery.


e.
A462104

Disconnect the 2 HV battery junction block assembly connectors.

NOTICE:

Insulate the disconnected high-voltage connectors with insulating tape.



f.
A462106

Remove the 4 nuts and HV battery junction block assembly from the HV battery.

NOTICE:

If the HV battery junction block assembly has been struck or dropped, replace it with a new one.



Hide G92Z2 19.REMOVE HYBRID BATTERY TERMINAL BLOCK

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A462109

Disconnect the hybrid battery terminal block connector.

NOTICE:

Insulate the disconnected high-voltage connector with insulating tape.



b.
A462110

Disengage the claw to remove the hybrid battery terminal block from the HV battery.