Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model) › from 2020.05
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0376193 ENTRY AND START SYSTEM(for Start Function, HV Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  Power Source Mode does not Change to ON (IG and ACC)  


DESCRIPTION

When the power switch cannot be turned on (ACC) or on (IG), there may be a malfunction in interior certification, or the ACC relay or IG relay system. If interior certification does not succeed, the certification ECU (smart key ECU assembly) may be malfunctioning, or communication may not be possible between the No. 1 indoor electrical key antenna assembly (front floor), No. 1 indoor electrical key antenna assembly (rear floor) or No. 1 indoor electrical key antenna assembly (inside luggage compartment), the electrical key transmitter sub-assembly, and the door control receiver.

When the electrical key transmitter sub-assembly is brought into the cabin, the key ID code sent from the electrical key transmitter sub-assembly and the key ID code stored in the certification ECU (smart key ECU assembly) are certified. If these codes do not match and certification fails, the power switch cannot be turned on (ACC) or on (IG).

When the door is unlocked and the electrical key transmitter sub-assembly is brought into the cabin, the certification ECU (smart key ECU assembly) activates the indoor electrical key antenna and forms a detection area. When the electrical key transmitter sub-assembly is recognized inside the detection area, it returns the key ID code. This is received by the door control receiver, which then sends it to the certification ECU (smart key ECU assembly).

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Power source mode does not change to on (IG) or on (ACC)
Power Source Control
·

Start Switch1

·

Start Switch2

·

IG Relay Monitor (Inside)

·

ACC Relay Monitor

·

IG Relay Monitor (Outside)

·

Latch Circuit

·

Power Supply Condition



WIRING DIAGRAM

E410649E05
4.938,6.25 7.156,6.844 2.219,0.594 10 false Certification ECU (Smart Key ECU Assembly) 6.542,5.448 6.896,5.896 0.354,0.448 10 false IC 6.51,2.885 6.865,3.333 0.354,0.448 10 false IC 5.625,0.542 5.979,0.99 0.354,0.448 10 false +B 5.26,2.563 5.615,3.01 0.354,0.448 10 false G54 5.26,3.198 5.615,3.646 0.354,0.448 10 false G54 5.25,3.823 5.604,4.271 0.354,0.448 10 false G54 5.271,5.281 5.625,5.729 0.354,0.448 10 false M7 5.271,5.083 5.625,5.531 0.354,0.448 10 false 25 2.031,5.156 2.385,5.604 0.354,0.448 10 false 3 1.833,5.188 2.188,5.635 0.354,0.448 10 false L 5.313,2.365 5.667,2.813 0.354,0.448 10 false 23 1.052,5.531 1.406,5.979 0.354,0.448 10 false GND 1.427,5.354 1.781,5.802 0.354,0.448 10 false IC 1.104,5.26 1.458,5.708 0.354,0.448 10 false B 0.906,5.188 1.271,5.583 0.365,0.396 10 false 7 1.052,4.896 1.521,5.25 0.469,0.354 10 false STOP 1.844,4.74 3.396,5.177 1.552,0.438 10 false from Auxiliary Battery 2.625,2.458 2.979,2.906 0.354,0.448 10 false SS1 2.625,3.083 2.979,3.531 0.354,0.448 10 false SS2 2.5,3.708 3.083,4.156 0.583,0.448 10 false AGND 1.906,4.292 3.458,4.729 1.552,0.438 10 false Power Switch 1.865,4.156 2.219,4.604 0.354,0.448 10 false G55 5.646,2.469 6.26,2.917 0.615,0.448 10 false SSW1 5.646,3.094 6.26,3.542 0.615,0.448 10 false SSW2 5.635,3.688 6.219,4.135 0.583,0.448 10 false AGND 5.323,2.99 5.677,3.438 0.354,0.448 10 false 21 5.302,3.615 5.656,4.063 0.354,0.448 10 false 11 2.99,2.448 3.344,2.896 0.354,0.448 10 false 5 2.99,3.073 3.344,3.521 0.354,0.448 10 false 1 2.99,3.698 3.344,4.146 0.354,0.448 10 false 6 5.292,1.25 5.646,1.698 0.354,0.448 10 false G54 5.26,0.563 5.615,1.01 0.354,0.448 10 false G54 4.854,0.729 5.208,1.177 0.354,0.448 10 false AM2 3.104,0.552 4.656,0.99 1.552,0.438 10 false from Auxiliary Battery 5.323,0.365 5.677,0.813 0.354,0.448 10 false 4 5.323,1.042 5.677,1.49 0.354,0.448 10 false 18 0.99,5.906 1.344,6.354 0.354,0.448 10 false A40 1,6.094 3.219,6.688 2.219,0.594 10 false Stop Light Switch Assembly 5.938,2.115 6.292,2.563 0.354,0.448 10 false +B 5.646,1.26 6,1.708 0.354,0.448 10 false E 5.646,5.188 6.229,5.635 0.583,0.448 10 false STP1 0.896,5.458 1.26,5.854 0.365,0.396 10 false 2

E410293E30
5.375,8.156 6.573,8.448 1.198,0.292 10 false Certification ECU 5.333,8.333 7.156,8.74 1.823,0.406 10 false (Smart Key ECU Assembly) 5.26,0.74 5.594,0.938 0.333,0.198 10 false G54 5.26,1.885 5.594,2.094 0.333,0.208 10 false G54 5.344,1.698 5.802,1.896 0.458,0.198 10 false 9 5.365,0.573 5.823,0.771 0.458,0.198 10 false 8 6.135,1.313 6.594,1.51 0.458,0.198 10 false IC 5.635,0.646 6.094,0.844 0.458,0.198 10 false CLG5 2.802,2.365 5,2.844 2.198,0.479 10 false No. 1 Indoor Electrical Key Antenna Assembly (Front Floor) 3.667,0.646 4.125,0.844 0.458,0.198 10 false ANTE5 3.76,1.792 4.219,1.99 0.458,0.198 10 false CLGB 4.24,0.646 4.698,0.844 0.458,0.198 10 false 1 4.24,1.792 4.698,1.99 0.458,0.198 10 false 3 2.781,2.188 3.24,2.385 0.458,0.198 10 false G59 5.646,1.792 6.104,1.99 0.458,0.198 10 false CG5B 6.156,3.979 6.615,4.177 0.458,0.198 10 false IC 5.656,3.26 6.115,3.458 0.458,0.198 10 false CLG6 5.646,4.406 6.104,4.604 0.458,0.198 10 false CG6B 5.313,3.344 5.583,3.531 0.271,0.188 10 false M7 5.302,4.5 5.583,4.677 0.281,0.177 10 false M7 5.354,3.167 5.813,3.365 0.458,0.198 10 false 5 5.354,4.292 5.813,4.49 0.458,0.198 10 false 6 2.76,4.979 4.958,5.458 2.198,0.479 10 false No. 1 Indoor Electrical Key Antenna Assembly (Rear Floor) 2.76,4.823 3.094,5.021 0.333,0.198 10 false N71 3.792,3.24 4.25,3.438 0.458,0.198 10 false CLG 3.76,4.417 4.219,4.615 0.458,0.198 10 false CLGB 4.219,3.24 4.677,3.438 0.458,0.198 10 false 1 4.24,4.417 4.698,4.615 0.458,0.198 10 false 3 5.313,5.958 5.771,6.156 0.458,0.198 10 false M7 5.302,7.115 5.573,7.302 0.271,0.188 10 false M7 5.313,6.906 5.771,7.104 0.458,0.198 10 false 10 5.323,5.771 5.781,5.969 0.458,0.198 10 false 11 6.135,6.49 6.594,6.688 0.458,0.198 10 false IC 5.646,5.865 6.104,6.063 0.458,0.198 10 false CLG7 5.635,7.021 6.094,7.219 0.458,0.198 10 false CG7B 3.688,5.865 4.146,6.063 0.458,0.198 10 false ANTE7 3.771,7.031 4.229,7.229 0.458,0.198 10 false CLGB 2.635,7.563 5.469,8.042 2.833,0.479 10 false No. 1 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment) 2.635,7.406 3.094,7.604 0.458,0.198 10 false M10 4.219,5.865 4.677,6.063 0.458,0.198 10 false 1 4.229,7.031 4.688,7.229 0.458,0.198 10 false 3

E414506E06
1.167,7.302 4.125,7.833 2.958,0.531 10 false Instrument Panel Junction Block Assembly 1.406,5.823 2.479,6.021 1.073,0.198 10 false ECU-ACC 1.208,2.021 2.344,2.26 1.135,0.24 10 false ECU-IG1 NO.1 1.365,4.552 2.479,4.813 1.115,0.26 10 false ECU-IG2 NO.3 1.469,3.292 2.635,3.625 1.167,0.333 10 false WASHER 2.75,5.063 4.896,5.26 2.146,0.198 10 false IG2 NO.2 Relay 2.76,2.583 4.573,3.052 1.813,0.469 10 false IG1 NO.1 Relay 2.75,3.833 4.896,4.031 2.146,0.198 10 false IG1 NO.2 Relay 2.833,6.333 4.208,6.531 1.375,0.198 10 false ACC Relay 5.25,7.479 7.073,7.969 1.823,0.49 10 false Certification ECU (Smart Key ECU Assembly) 3.302,0.375 4.781,0.656 1.479,0.281 10 false from Auxiliary Battery 5.75,2.219 6.365,2.417 0.615,0.198 10 false IG1D 5.75,6 6.365,6.198 0.615,0.198 10 false ACCD 4.354,1.604 4.667,1.802 0.313,0.198 10 false 4K 4.375,5.99 4.688,6.188 0.313,0.198 10 false 4A 0.656,5.635 0.969,5.833 0.313,0.198 10 false 4A 4.365,4.375 4.677,4.573 0.313,0.198 10 false 4L 0.667,2.219 0.979,2.417 0.313,0.198 10 false 4D 0.667,6.781 0.979,6.979 0.313,0.198 10 false 4F 0.667,3.125 0.979,3.323 0.313,0.198 10 false 4F 0.667,1.854 0.979,2.052 0.313,0.198 10 false 4D 4.354,2.219 4.667,2.417 0.313,0.198 10 false 4A 0.677,4.375 0.99,4.573 0.313,0.198 10 false 4F 4.396,1.417 4.708,1.615 0.313,0.198 10 false 1 4.354,2.031 4.604,2.229 0.25,0.198 10 false 17 4.375,4.188 4.688,4.385 0.313,0.198 10 false 1 4.365,5.802 4.677,6 0.313,0.198 10 false 30 0.677,1.656 0.958,1.938 0.281,0.281 10 false 31 0.708,2.042 0.865,2.24 0.156,0.198 10 false 3 0.719,2.927 1.031,3.125 0.313,0.198 10 false 2 0.677,4.198 0.969,4.417 0.292,0.219 10 false 15 0.656,5.448 0.969,5.646 0.313,0.198 10 false 40 0.656,6.583 0.969,6.781 0.313,0.198 10 false 13 5.479,2.115 5.74,2.344 0.26,0.229 10 false 17 5.469,5.896 5.792,6.094 0.323,0.198 10 false 16 5.25,7.323 5.563,7.521 0.313,0.198 10 false G54

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

·

If the entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>CUSTOMIZE PARAMETERS

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to the Service Bulletin.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>PRECAUTION

·

After completing repairs, confirm that the problem does not recur.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

An antenna coil is connected between the terminals of the indoor electrical key antenna.

·

The door control receiver is also involved in interior certification.



HINT:
·

If interior certification does not succeed, the History of Reason for Operation may remain in the certification ECU (smart key ECU assembly).

·

If the operation history remains, refer to the history table to determine the conditions and narrow down any trouble areas.



Body Electrical > Entry&Start > Utility
Tester Display
Operation History
50005 125 52

PROCEDURE

1.CHECK PUSH-BUTTON START FUNCTION
a.

Get into the vehicle while carrying the electrical key transmitter sub-assembly that has already been registered.


b.

Change the shift state to park (P).


c.

Check that the power source mode changes when the power switch is pressed without depressing the brake pedal.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>OPERATION CHECK


Result:
Result Proceed to
Power source mode does not change when the electrical key transmitter sub-assembly is inside the push-button start function operation range only for the front side A
Power source mode does not change when the electrical key transmitter sub-assembly is inside the push-button start function operation range only for the rear side B
Power source mode does not change when the electrical key transmitter sub-assembly is inside the push-button start function operation range only for the luggage compartment C
Power source mode does not change when the electrical key transmitter sub-assembly is inside any push-button start function operation range D



A

2.CHECK WAVE ENVIRONMENT

B

6.CHECK WAVE ENVIRONMENT

C

10.CHECK WAVE ENVIRONMENT

D

14.CHECK TRANSMITTER BATTERY
2.CHECK WAVE ENVIRONMENT
a.

Install the transmitter battery to the electrical key transmitter sub-assembly.

Click hereGeneral>MAINTENANCE>TRANSMITTER BATTERY(w/ Entry and Start System)>REMOVAL


b.

Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (front floor) and perform an entry and start system check.

NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>PARTS LOCATION



HINT:
·

As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.



OK:

The hybrid control system starts when the electrical key transmitter sub-assembly is held near each indoor electrical key antenna assembly and the power switch is pressed with the brake pedal depressed.


Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

3.CHECK KEY DIAGNOSTIC MODE
3.CHECK KEY DIAGNOSTIC MODE
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Utility / Communication Check(Key Diag Mode).


e.
B522180C01
2.969,2.021 2.667,2.021 2.667,2.021 0.719,1.021 true 2.688,2.021 2.167,1.063 true 3.01,1.938 3.323,2.094 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 1 indoor electrical key antenna assembly (front floor).

When the electrical key transmitter sub-assembly is at either inspection point, check that the buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.

·

It is possible to check which No. 1 indoor electrical key antenna assembly (front floor) is operating by the sounding of the buzzer.

·

When the buzzer does not sound for No. 1 indoor electrical key antenna assembly (front floor), it can be judged that the certification ECU (smart key ECU assembly), which controls the No. 1 indoor electrical key antenna assembly (front floor), is malfunctioning.




Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
Result:
Result Proceed to
The buzzer sounds A
The buzzer does not sound B



A

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))

B

AFFECTED BY WAVE INTERFERENCE

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))
a.

Disconnect the G54 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G59 No. 1 indoor electrical key antenna assembly (front floor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-8 (CLG5) - G59-1 (ANTE5) Always Below 1 Ω
G54-9 (CG5B) - G59-3 (CLGB) Always Below 1 Ω
G54-8 (CLG5) or G59-1 (ANTE5) - Other terminals and body ground Always 10 kΩ or higher
G54-9 (CG5B) or G59-3 (CLGB) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the G54 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))
a.

Using an oscilloscope, check the waveform.

B536654C08
1.646,0.552 2.073,0.781 0.427,0.229 1.198,2 1.323,2 1.323,2 1.615,1.583 true 2.563,2.01 2.375,2.01 2.375,2.01 2.01,1.594 true 0.979,0.75 1.292,0.906 0.313,0.156 10 false *a 4.115,0.396 4.427,0.552 0.313,0.156 10 false *b 4.729,1.979 5.042,2.135 0.313,0.156 10 false *c 5.604,2.01 5.917,2.167 0.313,0.156 10 false *d 0.708,1.906 1.5,2.26 0.792,0.354 10 false ANTE5 2.625,1.938 3.417,2.292 0.792,0.354 10 false CLGB 1.708,0.583 2.073,0.802 0.365,0.219 10 false G59 3.927,1.292 4.719,1.646 0.792,0.354 10 false GND
*a Front view of wire harness connector
(to No. 1 Indoor Electrical Key Antenna Assembly (Front Floor))
*b Waveform
*c For 30 seconds after closing any door *d After 30 seconds or more have elapsed since any door closed


OK:
Tester Connection Condition Tool Setting Specified Condition
G59-1 (ANTE5) - G59-3 (CLGB) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

6.CHECK WAVE ENVIRONMENT
a.

Install the transmitter battery to the electrical key transmitter sub-assembly.

Click hereGeneral>MAINTENANCE>TRANSMITTER BATTERY(w/ Entry and Start System)>REMOVAL


b.

Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (rear floor) and perform an entry and start system check.

HINT:

Check that the customize setting "Ignition Available Area" is set to "All".

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>CUSTOMIZE PARAMETERS


NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 1 indoor electrical key antenna assembly (rear floor).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>PARTS LOCATION



HINT:
·

As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.



OK:

The hybrid control system starts when the electrical key transmitter sub-assembly is held near each indoor electrical key antenna assembly and the power switch is pressed with the brake pedal depressed.


Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

7.CHECK KEY DIAGNOSTIC MODE
7.CHECK KEY DIAGNOSTIC MODE
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Utility / Communication Check(Key Diag Mode).


e.
B522181C01
0.667,0.51 2.76,0.104 2.76,0.104 2.948,0.104 true 2.146,0.49 2.698,0.125 true 3.042,0.031 3.354,0.229 0.313,0.198 10 false *a
*a Inspection Point


Check the No. 1 indoor electrical key antenna assembly (rear floor).

When the electrical key transmitter sub-assembly is at either inspection point, check that the buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.

·

It is possible to check which No. 1 indoor electrical key antenna assembly (rear floor) is operating by the sounding of the buzzer.

·

When the buzzer does not sound for No. 1 indoor electrical key antenna assembly (rear floor), it can be judged that the certification ECU (smart key ECU assembly), which controls the No. 1 indoor electrical key antenna assembly (rear floor), is malfunctioning.




Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
Result:
Result Proceed to
The buzzer sounds A
The buzzer does not sound B



A

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))

B

AFFECTED BY WAVE INTERFERENCE

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))
a.

Disconnect the M7 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the N71 No. 1 indoor electrical key antenna assembly (rear floor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M7-5 (CLG6) - N71-1 (CLG) Always Below 1 Ω
M7-6 (CG6B) - N71-3 (CLGB) Always Below 1 Ω
M7-5 (CLG6) or N71-1 (CLG) - Other terminals and body ground Always 10 kΩ or higher
M7-6 (CG6B) or N71-3 (CLGB) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the M7 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))
a.

Using an oscilloscope, check the waveform.

B536654C31
1.646,0.552 2.073,0.781 0.427,0.229 1.198,2 1.323,2 1.323,2 1.615,1.583 true 2.563,2.01 2.375,2.01 2.375,2.01 2.01,1.594 true 0.979,0.75 1.292,0.906 0.313,0.156 10 false *a 4.115,0.396 4.427,0.552 0.313,0.156 10 false *b 4.729,1.979 5.042,2.135 0.313,0.156 10 false *c 5.604,2.01 5.917,2.167 0.313,0.156 10 false *d 0.854,1.906 1.646,2.26 0.792,0.354 10 false CLG 2.625,1.938 3.417,2.292 0.792,0.354 10 false CLGB 1.74,0.583 2.104,0.802 0.365,0.219 10 false N71 3.927,1.292 4.719,1.646 0.792,0.354 10 false GND
*a Front view of wire harness connector
(to No. 1 Indoor Electrical Key Antenna Assembly (Rear Floor))
*b Waveform
*c For 30 seconds after closing any door *d After 30 seconds or more have elapsed since any door closed


OK:
Tester Connection Condition Tool Setting Specified Condition
N71-1 (CLG) - N71-3 (CLGB) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

10.CHECK WAVE ENVIRONMENT
a.

Install the transmitter battery to the electrical key transmitter sub-assembly.

Click hereGeneral>MAINTENANCE>TRANSMITTER BATTERY(w/ Entry and Start System)>REMOVAL


b.

Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (inside luggage compartment) and perform an entry and start system check.

HINT:

Check that the customize setting "Ignition Available Area" is set to "All".

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>CUSTOMIZE PARAMETERS


NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 1 indoor electrical key antenna assembly (inside luggage compartment).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>PARTS LOCATION



HINT:
·

As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.



OK:

The hybrid control system starts when the electrical key transmitter sub-assembly is held near each indoor electrical key antenna assembly and the power switch is pressed with the brake pedal depressed.


Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

11.CHECK KEY DIAGNOSTIC MODE
11.CHECK KEY DIAGNOSTIC MODE
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Utility / Communication Check(Key Diag Mode).


e.
B522182C01
2.229,0.823 2.448,0.25 true 1.563,1.75 2.438,0.229 2.438,0.229 2.979,0.229 true 3.052,0.156 3.365,0.313 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 1 indoor electrical key antenna assembly (inside luggage compartment).

When the electrical key transmitter sub-assembly is at either inspection point, check that the buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.

·

It is possible to check which No. 1 indoor electrical key antenna assembly (inside luggage compartment) is operating by the sounding of the buzzer.

·

When the buzzer does not sound for No. 1 indoor electrical key antenna assembly (inside luggage compartment), it can be judged that the certification ECU (smart key ECU assembly), which controls the No. 1 indoor electrical key antenna assembly (inside luggage compartment), is malfunctioning.




Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
Result:
Result Proceed to
The buzzer sounds A
The buzzer does not sound B



A

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT))

B

AFFECTED BY WAVE INTERFERENCE

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT))
a.

Disconnect the M7 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the M10 No. 1 indoor electrical key antenna assembly (inside luggage compartment) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M7-11 (CLG7) - M10-1 (ANTE7) Always Below 1 Ω
M7-10 (CG7B) - M10-3 (CLGB) Always Below 1 Ω
M7-11 (CLG7) or M10-1 (ANTE7) - Other terminals and body ground Always 10 kΩ or higher
M7-10 (CG7B) or M10-3 (CLGB) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the M7 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

13.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT))
a.

Using an oscilloscope, check the waveform.

B536654C10
1.646,0.552 2.073,0.781 0.427,0.229 1.198,2 1.323,2 1.323,2 1.615,1.583 true 2.563,2.01 2.375,2.01 2.375,2.01 2.01,1.594 true 0.979,0.75 1.292,0.906 0.313,0.156 10 false *a 4.115,0.396 4.427,0.552 0.313,0.156 10 false *b 4.729,1.979 5.042,2.135 0.313,0.156 10 false *c 5.604,2.01 5.917,2.167 0.313,0.156 10 false *d 0.708,1.906 1.5,2.26 0.792,0.354 10 false ANTE7 2.625,1.938 3.417,2.292 0.792,0.354 10 false CLGB 1.708,0.583 2.073,0.802 0.365,0.219 10 false M10 3.927,1.292 4.719,1.646 0.792,0.354 10 false GND
*a Front view of wire harness connector
(to No. 1 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment))
*b Waveform
*c For 30 seconds after closing any door *d After 30 seconds or more have elapsed since any door closed


OK:
Tester Connection Condition Tool Setting Specified Condition
M10-1 (ANTE7) - M10-3 (CLGB) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

14.CHECK TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

i.

Press and hold the lock switch of the electrical key transmitter sub-assembly for 5 seconds and check the number of times that the LED illuminates.

HINT:
·

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. "Yes" is displayed for the Data List item "Key Low Battery" when this voltage information indicates 2.2 V or less.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>DATA LIST / ACTIVE TEST

·

Even if the transmitter battery is depleted, it is still possible to start the hybrid control system by holding the electrical key transmitter sub-assembly near the power switch, depressing the brake pedal and pressing the power switch.





Result:
Result Proceed to
LED illuminates 3 times or more when switch is pressed and held A
LED does not illuminate when switch is pressed and held B
LED illuminates once or twice but not a third time C



A

15.SYSTEM CHECK

B

21.INSPECT TRANSMITTER BATTERY

C

15.SYSTEM CHECK
a.

Check the vehicle specification.


Result:
Result Proceed to
w/ Entry Function A
w/o Entry Function B



A

16.CHECK ENTRY LOCK / UNLOCK FUNCTION

B

17.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
16.CHECK ENTRY LOCK / UNLOCK FUNCTION
a.

Check that the entry lock and unlock functions operate on each door.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function, HV Model)>OPERATION CHECK

HINT:

If the door control receiver is defective, code verification does not begin in the cabin and the entry lock and unlock functions do not operate.



Result:
Result Proceed to
Entry lock/unlock functions operate normally A
An entry lock/unlock functions does not operate normally B



A

18.READ VALUE USING GTS (START SWITCH1, START SWITCH2)

B

GO TO ENTRY AND START SYSTEM (for Entry Function) (All door entry lock/unlock functions and wireless functions do not operate)

17.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock control system operate.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function, HV Model)>OPERATION CHECK

HINT:

If the door control receiver is defective, code verification does not begin in the cabin and the wireless door lock control system do not operate.



Result:
Result Proceed to
Wireless door lock control system operate normally A
A wireless door lock control system does not operate normally B



A

18.READ VALUE USING GTS (START SWITCH1, START SWITCH2)

B

GO TO WIRELESS DOOR LOCK CONTROL SYSTEM (Only Wireless Control Function is Inoperative)

18.READ VALUE USING GTS (START SWITCH1, START SWITCH2)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Start Switch1 Power switch 1 status OFF or ON OFF: Power switch not pressed
ON: Power switch pressed
·

If the power switch is pressed for a short time, the display may not change.

·

Use this item to determine if the power switch input signal is malfunctioning.


Start Switch2 Power switch 2 status OFF or ON OFF: Power switch not pressed
ON: Power switch pressed
·

Backup for power switch 1. However, when the power switch is pressed and held, the power source mode can only be changed when both power switch 1 and 2 are normal.

·

Behaves the same way as power switch 1.


Body Electrical > Power Source Control > Data List
Tester Display
Start Switch1
Start Switch2
50003 223 4,5
OK:

The GTS display changes correctly in response to the power switch operation.



Result:
Proceed to
OK
NG



OK

19.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

22.INSPECT POWER SWITCH
19.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Measure the voltage while confirming the power source mode on the Data List.

B427583C80
4.615,0.49 4.948,0.698 0.333,0.208 3.844,2.24 4.26,2.24 4.26,2.24 4.26,1.229 false 4.75,2.24 4.354,2.24 4.354,2.24 4.354,1.229 false 0.198,0.073 0.51,0.271 0.313,0.198 10 false *a 4.667,0.51 4.979,0.708 0.313,0.198 10 false G54 4.823,2.146 5.354,2.396 0.531,0.25 10 false ACCD 3.49,2.167 3.948,2.385 0.458,0.219 10 false IG1D
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state All OFF, ACC ON, IG ON or ST ON All OFF: Power switch off
ACC ON: Power switch on (ACC)
IG ON: Power switch on (IG)
ST ON: Sending hybrid control system start request signal
-
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 223 18
Standard Voltage:
Tester Connection Switch Condition Specified Condition
G54-17 (IG1D) - Body ground Power switch off 1 V or less
Power switch on (ACC)
Power switch on (IG) 9 V or higher
G54-16 (ACCD) - Body ground Power switch off 1 V or less
Power switch on (ACC) 8.5 V or higher
Power switch on (IG)



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

20.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)
a.
C376684C17
1.51,0.26 1.938,0.458 0.427,0.198 1.646,0.292 1.958,0.49 0.313,0.198 10 false 4D 0.146,0.229 0.458,0.427 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4D-3 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.INSPECT TRANSMITTER BATTERY
a.

Inspect the transmitter battery.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Entry and Start System)>INSPECTION

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

22.INSPECT POWER SWITCH


Result:
Proceed to
OK
NG



OK

23.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SWITCH)

NG

23.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SWITCH)
a.

Disconnect the G54 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-23 (SSW1) - G55-5 (SS1) Always Below 1 Ω
G54-21 (SSW2) - G55-1 (SS2) Always Below 1 Ω
G54-11 (AGND) - G55-6 (AGND) Always Below 1 Ω
G54-23 (SSW1) or G55-5 (SS1) - Other terminals and body ground Always 10 kΩ or higher
G54-21 (SSW2) or G55-1 (SS2) - Other terminals and body ground Always 10 kΩ or higher
G54-11 (AGND) or G55-6 (AGND) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR