Home › Engine / Hybrid System › A25A-FXS (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › from 2020.08
RM3620E _51 Engine / Hybrid System _076696 A25A-FXS ENGINE MECHANICAL _0373300 CYLINDER HEAD GASKET A

A25A-FXS ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cylinder head gasket removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of ECM
w/ Canister Pump Module:

Perform Vehicle Identification Number (VIN) registration


DTC P063051 is output (Click here)
w/o Canister Pump Module:

Perform Vehicle Identification Number (VIN) or frame number registration


(Click here)
Grille shutter switch specification infomation Vehicle control history (RoB) [X260E] is stored (Click here)
(w/ Canister Pump Module)
(Click here)
(w/o Canister Pump Module)
·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Replacement of cam timing control motor with EDU assembly

·

Removal and installation of a cam timing control motor with EDU assembly

·

Replacement of camshaft timing gear assembly

·

Removal and installation of a camshaft timing gear assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of port fuel injector assembly

·

Replacement of direct fuel injector assembly

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Replacement of knock control sensor

·

Replacement of air fuel ratio sensor (sensor 2)


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
(w/ Canister Pump Module)
(Click here)
(w/o Canister Pump Module)
Front exhaust pipe assembly (w/ GPF) GPF deposition value clear
·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)(for 2WD)
(Click here)(for 4WD/AWD)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Replacement of headlight ECU sub-assembly LH
·

Synchronize the vehicle information

·

Perform headlight ECU sub-assembly LH initialization


Lighting system (EXT) (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Perform headlight ECU sub-assembly LH initialization
Front wheel alignment adjustment Electronically controlled brake system
·

Reset memory

·

Calibration


VSC malfunction (Click here)(w/ vacuum brake booster)
(Click here)(w/o vacuum brake booster)
Front bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for HV model) (Click here)
Front television camera view adjustment Panoramic view monitor system (for HV model) (Click here)

NOTICE:
·

After the power switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the power switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

Hide 1.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

Hide 88310 3.REMOVE COMPRESSOR ASSEMBLY WITH PULLEY

Hide 16207 4.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16260 5.REMOVE FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

Hide 89481B 6.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ GPF)

Hide 25760 7.REMOVE VACUUM TRANSMITTING HOSE ASSEMBLY (w/ GPF)

Hide 25706 8.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ GPF)

Hide 17167 9.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 22030 12.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 25680 13.REMOVE EGR COOLER ASSEMBLY

Hide 25601 14.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 16279 17.REMOVE NO. 3 WATER BY-PASS PIPE

Hide 16278 18.REMOVE NO. 2 WATER BY-PASS PIPE

Hide 17177 20.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 23901 21.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide 23801P 22.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23100X 23.REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Hide 16295 24.REMOVE NO. 7 WATER BY-PASS HOSE

Hide 23807 25.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23807V 26.REMOVE NO. 1 DELIVERY PIPE SPACER

Hide 23291 27.REMOVE INJECTOR VIBRATION INSULATOR

Hide 23250F 29.REMOVE PORT FUEL INJECTOR ASSEMBLY

Hide 23250E 31.REMOVE DIRECT FUEL INJECTOR ASSEMBLY

Hide 11452 34.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 15250 35.REMOVE OIL PRESSURE CONTROL VALVE ASSEMBLY

Hide 11102A 36.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11102A 37.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 15370 38.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 13090D 39.REMOVE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

Hide 40.DISCONNECT NO. 1 WATER BY-PASS HOSE (w/ Oil Cooler)

a.
A411195

Slide the clip and disconnect the No. 1 water by-pass hose from the cylinder block sub-assembly.


Hide 16264D 41.DISCONNECT NO. 2 WATER BY-PASS HOSE (w/ Oil Cooler)

a.
A411196

Slide the clip and disconnect the No. 2 water by-pass hose from the No. 1 water by-pass pipe sub-assembly.


Hide 13470 42.REMOVE CRANKSHAFT PULLEY ASSEMBLY

Hide 16305E 44.REMOVE OUTLET WATER BY-PASS SUB-ASSEMBLY

Hide 11201 45.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11193 46.REMOVE SPARK PLUG TUBE GASKET

Hide 12315A 47.REMOVE ENGINE MOUNTING BRACKET RH

Hide 11320B 48.REMOVE NO. 2 TIMING CHAIN COVER ASSEMBLY

Hide 11301C 49.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 50.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Hide 13507A 51.REMOVE OIL PUMP DRIVE CHAIN SUB-ASSEMBLY

Hide 13050 52.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13540 54.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 55.REMOVE CHAIN TENSIONER SLIPPER

Hide 13561 56.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13070A 57.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 11310 58.REMOVE TIMING CHAIN COVER ASSEMBLY

Hide 23477 59.REMOVE FUEL PUMP LIFTER GUIDE

Hide 11103 60.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13801 64.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 65.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11101 67.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 68.REMOVE CYLINDER HEAD GASKET

A403803

a.

Remove the cylinder head gasket from the cylinder block sub-assembly.


Hide 11101A 69.INSPECT CYLINDER HEAD SET BOLT

Hide 11101 70.INSPECT CYLINDER HEAD SUB-ASSEMBLY