The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump removal/installation are shown below.
Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2. DISCHARGE FUEL SYSTEM PRESSURE
58410B
3.REMOVE DECK BOARD ASSEMBLY
58416K
4.REMOVE REAR NO. 2 FLOOR BOARD
65351A
5.REMOVE BATTERY HOLE COVER
6.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
7.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY
72693
8.REMOVE REAR SEAT CUSHION LOCK HOOK
67918E
9.REMOVE REAR DOOR SCUFF PLATE LH
58467H
10.REMOVE NO. 3 BATTERY SERVICE COVER BOARD
67917C
11.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
58466J
12.REMOVE NO. 2 BATTERY SERVICE COVER BOARD
58464D
13.REMOVE BATTERY SERVICE COVER BOARD
58903A
14.REMOVE REAR CONSOLE END PANEL SUB-ASSEMBLY
58325E
15.REMOVE REAR FLOOR SERVICE HOLE COVER
Fold back the floor carpet.
Remove the 3 bolts and rear floor service hole cover.
Disconnect the 2 connectors from the fuel suction with pump and gauge tube assembly.
77026B
16.DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
Disconnect the No. 1 fuel evaporation tube sub-assembly from the fuel suction with pump and gauge tube assembly.
Click hereEngine / Hybrid System>A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION
77209C
17.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
| *1 | Tube Joint Clip |
| *2 | Fuel Tank Main Tube Sub-assembly |
| *a | Nylon Tube |
| *b | Fuel Tube Joint |
| *c | Plate Sub-assembly |
| *d | O-ring |
|
Pull off |
|
Pull off |
Remove the tube joint clip, and pull off the fuel tube joint of the fuel tank main tube sub-assembly.
Remove any foreign matter on the fuel tube joint before performing this work.
Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).
Be sure to disconnect the fuel tube joint by hand.
Do not bend, twist, pinch or kink the nylon tube.
Cover the disconnected fuel tube joint with a plastic bag to prevent damage and contamination.
If the fuel tube joint and plate sub-assembly are stuck, push and pull to release them.
77144
18.REMOVE FUEL PUMP GAUGE RETAINER
Detach the claw and remove the No. 1 fuel tube clamp from the fuel pump gauge retainer.
Remove the fuel pump gauge retainer.
| *a | SST (Plate) |
| *b | SST (Bolt) |
| *c | SST (Claw) |
| *d | Insertion Point |
Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.
Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.
While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).
| *a | SST (Handle) |
| *b | Extension Bar |
| *c | SST (Bolt) |
| *d | SST (Plate) |
| *e | SST (Claw) |
Install SST (handle) and an extension bar to SST (plate).
Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing down on SST, rotate SST (handle) slowly to loosen the fuel pump gauge retainer.
When turning SST (handle), take care not to hit the console box assembly with your hands or SST (handle).
Do not use any tools other than specified in this operation as this may result in damage to the fuel pump gauge retainer or the fuel tank assembly.
Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.
Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.
Do not spin SST too fast or use an impact wrench as this may result in damage to components.
If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.
While pressing down on the fuel suction with pump and gauge tube assembly, remove the fuel pump gauge retainer.
77020A
19.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
Remove the fuel suction with pump and gauge tube assembly from the fuel tank assembly.
Be careful not to bend the arm of the fuel sender gauge assembly.
Remove the gasket from the fuel tank assembly.