Home › Engine / Hybrid System › M20A-FKS (FUEL) › FUEL TANK › from 2020.08
RM3620E _51 Engine / Hybrid System _076682 M20A-FKS FUEL _0376395 FUEL TANK A

M20A-FKS FUEL  FUEL TANK  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel tank assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Reset back door close position Power back door system (Click here)
Power back door initialization Power door lock control system (Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A344817

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.



NOTICE:

Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is pressed into the fuel suction plate sub-assembly.

Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 77010 4.REMOVE FUEL TANK VENT TUBE ASSEMBLY

Hide 77020A 5.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 6.DRAIN FUEL

Hide 17430 7.REMOVE TAIL EXHAUST PIPE ASSEMBLY

Hide 37110 8.REMOVE PROPELLER SHAFT ASSEMBLY (for 4WD/AWD)

Hide 53896B 9.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH

Hide 53895B 10.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH

Hide 51441 11.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51420 12.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 58166A 13.REMOVE FRONT FLOOR COVER LH (w/ Cover)

a.
A434505

Detach the 3 clips and remove the 2 bolts and 5 screws.


b.
A434506

Loosen the 3 nuts and remove the front floor cover LH from the body.


Hide 58399D 14.REMOVE NO. 2 FLOOR UNDER COVER (w/ Cover)

a.
A434507

Detach the 3 clips and remove the 2 bolts.


b.
A434508

Loosen the 4 nuts and remove the No. 2 floor under cover from the body.


Hide 58165C 15.REMOVE FRONT FLOOR COVER RH (w/ Cover)

a.
A434509

Detach the 2 clips and remove the 2 bolts and 4 screws.


b.
A434510

Loosen the 3 nuts and remove the front floor cover RH from the body.


Hide 58398F 16.REMOVE NO. 1 FLOOR UNDER COVER (w/ Cover)

a.
A434511

Detach the 3 clips and remove the 2 bolts.


b.
A434512

Loosen the nut and remove the No. 1 floor under cover from the body.


Hide 77606 17.REMOVE NO. 1 FUEL TANK PROTECTOR

a.
A436333

Remove the 2 nuts and No. 1 fuel tank protector from the fuel tank band.


Hide 77026B 18.DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A434524

Slide the clamp and disconnect the No. 1 fuel evaporation tube sub-assembly from the charcoal canister assembly.


Hide 77209C 19.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A434523

w/o Cover:

Remove the fuel tank protector from the fuel tank main tube sub-assembly.


b.
A434525

Disconnect the fuel tank main tube sub-assembly from the fuel tube.

Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 20.DISCONNECT FUEL TANK BREATHER TUBE

a.
A434514

Disconnect the fuel tank breather tube from the fuel tank filler pipe assembly.

Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 21.DISCONNECT FUEL TANK FILLER PIPE SUB-ASSEMBLY

a.
A434517

Disconnect the fuel tank filler pipe sub-assembly from the fuel tank filler pipe assembly.

Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77754B 22.DISCONNECT CHARCOAL CANISTER OUTLET HOSE

a.
A434631

Disconnect the charcoal canister outlet hose from the fuel tank filler pipe assembly.


Hide 77100 23.REMOVE FUEL TANK ASSEMBLY

CAUTION:

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.


a.
A434518

Using an engine lifter, support the fuel tank assembly.

HINT:

Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.



b.
A434630

Remove the 4 bolts and 2 fuel tank band sub-assemblies.


c.

Lower the engine lifter to remove the fuel tank assembly.

NOTICE:
·

Be careful not to drop the fuel tank assembly.

·

When removing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.




Hide 77754B 24.REMOVE CHARCOAL CANISTER OUTLET HOSE

a.
A434632

Remove the charcoal canister outlet hose from the fuel tank assembly.


Hide 77209C 25.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A434633

Detach the clamp and remove the fuel tank main tube sub-assembly from the fuel tank assembly.


Hide 77026B 26.REMOVE NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A434634

Detach the clamp and remove the No. 1 fuel evaporation tube sub-assembly from the fuel tank assembly.


Hide 77651A 27.REMOVE NO. 1 FUEL TANK CUSHION

a.
A434635

Remove the 2 No. 1 fuel tank cushions from the fuel tank assembly.


Hide 77606 28.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.
A434520

Detach the 4 clips and remove the No. 1 fuel tank protector sub-assembly from the fuel tank assembly.