The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the instrument panel safety pad assembly removal/installation are shown below.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1. TABLE OF BOLT, SCREW, NUT AND CLIP
All bolts, screws and clips relevant to installing and removing the instrument panel are shown along with their alphabetic code in the table below.
2. PRECAUTION
Be sure to read precaution thoroughly before servicing.
for HV Model with Occupant Classification System
for Gasoline Model with Occupant Classification System
w/o Occupant Classification System
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
58410B
3.REMOVE DECK BOARD ASSEMBLY (for HV Model)
58416K
4.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)
65351A
5.REMOVE BATTERY HOLE COVER (for HV Model)
6.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Disconnect the cable from the negative (-) auxiliary battery terminal.
for A25A-FKS:
for M20A-FKS:
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
7.REMOVE CONSOLE BOX ASSEMBLY
55405B
8.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (for Type A)
|
Remove in this Direction |
Detach the clip and claw and remove the center instrument cluster finish panel sub-assembly.
55424C
9.REMOVE RADIO TUNER FINISH PANEL (for Type A, w/ Radio Receiver Opening Cover)
|
Remove in this Direction |
Detach the clip and remove the radio tuner finish panel.
55422C
10.REMOVE CENTER UPPER INSTRUMENT CLUSTER FINISH PANEL
|
Remove in this Direction |
for Type A:
Using moulding remover B, detach the clip and remove the center upper instrument cluster finish panel.
for Type B:
|
Remove in this Direction |
Using moulding remover B, detach the clip.
|
Place Hand Here |
|
Remove in this Direction |
Using moulding remover B, detach the clip as shown in the illustration and remove the center upper instrument cluster finish panel.
11.REMOVE STEREO OPENING COVER WITH BRACKET (for Type A, w/ Cover)
Remove the 4 bolts.
|
Remove in this Direction |
Detach the clip and remove the stereo opening cover with bracket.
12.REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (for Radio Receiver Type)
13.REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)
55474B
14.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH
|
Remove in this Direction |
Detach the clip and guide and remove the instrument cluster finish panel garnish.
55410C
15.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and detach the claw and guide as shown in the illustration.
|
Remove in this Direction |
Pull towards the rear of the vehicle to detach the clip and remove the instrument cluster finish panel assembly.
83100
16.REMOVE COMBINATION METER ASSEMBLY
55900
17.REMOVE AIR CONDITIONING CONTROL ASSEMBLY
55434B
18.REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL
|
Place Hands Here |
|
Remove in this Direction |
Place both hands at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip and remove the lower center instrument panel finish panel assembly.
Disconnect each connector.
67914B
19.REMOVE FRONT DOOR SCUFF PLATE LH (for LHD)
62112
20.REMOVE COWL SIDE TRIM BOARD LH (for LHD)
Remove the cap nut.
|
Remove in this Direction |
Detach the clip and guide and remove the cowl side trim board LH.
55606
21.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)
|
Screw <A> |
Remove the 3 screws <A>.
|
Remove in this Direction |
Detach the claw and guide and lower the No. 1 instrument panel under cover sub-assembly in the direction of the arrow shown in the illustration.
w/ Foot Light:
Disconnect the connector and detach the clamp.
Detach the claw and remove the DLC3.
w/o Foot Light:
Detach the claw and remove the DLC3.
Even if there is no foot light, if there is a connector, disconnect the connector and detach the clamp.
|
Remove in this Direction |
Pull in the direction of the arrow shown in the illustration to detach the guide and remove the No. 1 instrument panel under cover sub-assembly.
62312B
22.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Remove the front door opening trim weatherstrip LH from the area shown in the illustration.
55318C
23.REMOVE INSTRUMENT SIDE PANEL LH
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration to detach the guide and remove the instrument side panel LH.
for RHD, w/ Airbag Cut Off Switch:
Disconnect the connector.
53601
24.REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Detach the claw in the direction (1) indicated by the arrow shown in the illustration.
Detach the guide in the direction (2) indicated by the arrow shown in the illustration and remove the hood lock control lever sub-assembly.
77306
25.REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for Gasoline Model)
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Detach the claw in the direction (1) indicated by the arrow shown in the illustration.
Detach the guide in the direction (2) indicated by the arrow shown in the illustration and remove the fuel lid lock open lever sub-assembly.
55545
26.REMOVE FUSE BOX OPENING COVER (for LHD)
|
Bolt <B> |
Remove the bolt <B>.
|
Remove in this Direction |
Pull in the direction indicated by the arrow to detach the clip.
| *A | for 6 Switch Type |
| *B | for 3 Switch Type |
Disconnect each connector.
Detach the clamp and remove the fuse box opening cover.
for HV Model:
Disconnect the connector.
55545
27.REMOVE FUSE BOX OPENING COVER (for RHD)
|
Bolt <B> |
Remove the bolt <B>.
|
Remove in this Direction |
Pull in the direction indicated by the arrow to detach the clip and remove the fuse box opening cover.
Disconnect each connector.
for HV Model:
Disconnect the connector.
55480D
28.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip and remove the lower instrument panel finish panel assembly.
w/ Entry and Start System:
Disconnect the connector.
73900
29.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
62212
30.REMOVE FRONT PILLAR GARNISH LH
55525
31.REMOVE NO. 1 SPEAKER HOLE COVER
|
Place Hand Here |
|
Remove in this Direction |
Lift up the part in the removal direction shown in the illustration to detach the clip.
|
Remove in this Direction |
Pull in the direction of the arrow shown in the illustration to detach the guide and remove the No. 1 speaker hole cover.
86160P
32.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (except 4 Speakers)
62311B
33.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Remove the front door opening trim weatherstrip RH from the area shown in the illustration.
67913B
34.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
62111C
35.REMOVE COWL SIDE TRIM BOARD RH
Remove the cap nut.
|
Remove in this Direction |
Detach the clip and guide and remove the cowl side trim board RH.
55607
36.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
|
Remove in this Direction |
Detach the claw and lower the No. 2 instrument panel under cover sub-assembly in the direction of the arrow shown in the illustration.
w/ Foot Light:
Disconnect the connector and detach the clamp.
Even if there is no foot light, if there is a connector, disconnect the connector and detach the clamp.
|
Remove in this Direction |
Pull in the direction of the arrow shown in the illustration to detach the guide and remove the No. 2 instrument panel under cover sub-assembly.
55550
37.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
| *1 | Glove Compartment Door Stopper Sub-assembly |
| *a | Stopper |
|
Remove in this Direction |
Detach the claw and remove the glove compartment door stopper sub-assembly.
Slightly bend the stoppers (A) and (B) in the directions indicated by the arrows in the illustration and open the glove compartment door assembly until the stoppers are released.
| *a | Closed Position |
| *b | Assembly Position |
|
Remove in this Direction |
Assembly position the glove compartment door assembly, pull it horizontally in the direction indicated by the arrow to detach the hinge and remove the glove compartment door assembly.
Pulling the glove compartment door assembly upward to remove it causes the hinges to deform. Be sure to pull out the glove compartment door assembly horizontally.
55433B
38.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL
|
Bolt <B> |
|
Screw <A> |
Remove the 3 screws <A> and 2 bolts <B>.
|
Remove in this Direction |
Detach the clip and remove the lower No. 2 instrument panel finish panel.
55475A
39.REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH
|
Place Hand Here |
|
Remove in this Direction |
Place your hand in the gap, and then, while pulling in the direction indicated by the arrow shown in the illustration, detach the clip in the order shown in the illustration and remove the No. 2 instrument cluster finish panel garnish.
55317A
40.REMOVE INSTRUMENT SIDE PANEL RH
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration to detach the guide and remove the instrument side panel RH.
for LHD, w/ Airbag Cut Off Switch:
Disconnect the connector.
62211
41.REMOVE FRONT PILLAR GARNISH RH
Use the same procedure described for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
55535B
42.REMOVE NO. 2 SPEAKER HOLE COVER
|
Place Hand Here |
|
Remove in this Direction |
Lift up the part in the removal direction shown in the illustration to detach the clip.
|
Remove in this Direction |
Pull in the direction of the arrow shown in the illustration to detach the guide and remove the No. 2 speaker hole cover.
86160P
43.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (except 4 Speakers)
Use the same procedure described for the other side.
86160L
44.REMOVE FRONT NO. 4 SPEAKER ASSEMBLY (for eCall)
84330
45.REMOVE HAZARD WARNING SIGNAL SWITCH ASSEMBLY
45287
46.REMOVE LOWER STEERING COLUMN COVER
47.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for LHD)
Pull and slide the lock slider as shown to release the connector lock and disconnect the passenger airbag connector.
When handling the passenger airbag connector, take care not to damage the airbag wire harness.
| *A | for Dual Type | *B | for Single Type |
| *a | Lock Slider | - | - |
|
Slide in this Direction | - | - |
Disconnect the connector and detach the guide.
|
Bolt <C> |
Remove the 2 bolts <C>.
Disconnect each connector.
w/ Interior Illumination:
Disconnect the connector.
Remove the 2 nuts and steering column assembly from the instrument panel reinforcement assembly.
for Automatic Air Conditioning System:
Detach the claw and remove the cooler (room temp. sensor) thermistor.
Detach the clamp.
Remove the 2 clips <D>.
Remove the 5 bolts <B> and nut <E>.
|
Bolt <B> |
|
Nut <E> |
|
Clip <D> | - | - |
Pull in the direction indicated by the arrow shown in the illustration and detach the guide and remove the instrument panel safety pad assembly.
|
Remove in this Direction | - | - |
48.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for RHD)
Pull and slide the lock slider as shown to release the connector lock and disconnect the passenger airbag connector.
When handling the passenger airbag connector, take care not to damage the airbag wire harness.
| *a | Lock Slider | - | - |
|
Slide in this Direction | - | - |
Disconnect the connector and detach the guide.
|
Bolt <C> |
Remove the 2 bolts <C>.
Disconnect each connector.
w/ Interior Illumination:
Disconnect the connector.
Remove the 2 nuts and steering column assembly from the instrument panel reinforcement assembly.
for Automatic Air Conditioning System:
Detach the claw and remove the cooler (room temp. sensor) thermistor.
Detach the clamp.
Remove the 2 clips <D>.
Remove the 5 bolts <B> and nut <E>.
|
Bolt <B> |
|
Nut <E> |
|
Clip <D> | - | - |
Pull in the direction indicated by the arrow shown in the illustration and detach the guide and remove the instrument panel safety pad assembly.
|
Remove in this Direction | - | - |