Home › Engine / Hybrid System · 2UZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0016    Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)

DTC    P0018    Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A)

for Preparation Click here


DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate intake valve open and close timing is controlled by the ECM. The ECM performs intake valve control by performing the following: 1) controlling the camshaft and camshaft timing oil control valve, and operating the camshaft timing gear; and 2) changing the relative positions of the gaps between the camshaft and crankshaft.

DTC No.
DTC Detection Condition
Trouble Area
P0016
Deviation in crankshaft position sensor signal and VVT sensor 1 (for bank 1) signal
(2 trip detection logic)
  1. Mechanical system (Timing belt has jumped tooth or belt stretched)
  2. OCV
  3. OCV filter
  4. Intake camshaft timing tube assembly
  5. ECM
P0018
Deviation in crankshaft position sensor signal and VVT sensor 2 (for bank 2) signal
(2 trip detection logic)
  1. Mechanical system (Timing belt has jumped tooth or belt stretched)
  2. OCV
  3. OCV filter
  4. Intake camshaft timing tube assembly
  5. ECM

MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learning value while the engine is idling. The VVT learning value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the most retarded angle while the engine is idling. If the VVT learning value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores the DTC P0016 (for bank 1) or P0018 (for bank 2).

MONITOR STRATEGY


Related DTCs
P0016: Camshaft timing misalignment at idling (bank 1 intake side)
P0018: Camshaft timing misalignment at idling (bank 2 intake side)
Required Sensors/Components
VVT actuator
Required Sensors/Components
Camshaft position sensor, Crankshaft position sensor
Frequency of Operation
Once per driving cycle
Duration
Within 1 minute
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0010, P0020 (VVT Oil Control Valve)
P0016, P0018 (VVT System - Misalignment)
P0102, P0103 (Mass Air Flow Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0335 (Crankshaft Position Sensor)
P1340 (Camshaft Position Sensor)
Engine RPM
400 to 1000 rpm

TYPICAL MALFUNCTION THRESHOLDS


One of following conditions met
-
VVT learning value when camshaft maximum retarded
Less than 22.5°CA
VVT learning value when camshaft maximum retarded
bank1: More than 44°CA
bank2: More than 47°CA

WIRING DIAGRAM

Refer to DTC P0335 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016 OR P0018)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0016 or P0018 is output
    A
    P0016 or P0018 and other DTCs are output
    B



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV)

HINT:
If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.

  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream ON.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2) / All Data / VVT Change Angle (Bank 1) or VVT Change Angle (Bank 2).

  1. Perform the Active Test. Check that the displacement angle varies.

    OK:
    Varies



NG
Go to step 4
OK


3.CHECK VALVE TIMING
A115368E03
  1. Remove the drive belt (Click here).

  1. Remove the timing belt cover LH and RH (Click here).

  1. Turn the crankshaft to align the alignment marks of the crankshaft.

  1. Align the notch of the crankshaft pulley with the "0" position.

  1. Confirm whether the alignment marks of the camshaft pulley and cylinder head cover are facing each other.

  1. If the alignment marks are not facing each other, turn the crankshaft clockwise by 360°. Confirm again if the alignment marks are facing each other.

    OK:
    The alignment marks of the camshaft pulley and the cylinder head cover face each other when the notch of the crankshaft pulley is in the "0" position.



NG
ADJUST VALVE TIMING
OK


4.INSPECT CAMSHAFT OIL CONTROL VALVE ASSEMBLY
A160397E12
A178642E01
  1. Remove the OCV.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    6.9 to 7.9 Ω

  1. Apply the positive battery voltage to terminal 1 and negative battery voltage to terminal 2. Check the valve operation.

    OK:
    Valve moves quickly.



NG
REPLACE CAMSHAFT OIL CONTROL VALVE (Click here)
OK


5.INSPECT OIL CONTROL VALVE FILTER
A086178E01
  1. Remove the cylinder head cover for bank 1 (Click here).

  1. Remove the cylinder head cover for bank 2 (Click here).

  1. Remove the camshaft bearing cap and OCV filter.

  1. Check that the filter is not clogged.

    OK:
    Filter is not clogged.



NG
CLEAN OIL CONTROL VALVE FILTER
OK


6.REPLACE CAMSHAFT TIMING TUBE ASSEMBLY
  1. Replace the camshaft timing tube assembly (Click here).


NEXT


7.CONFIRM WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Clear the DTC (Click here).

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the Techstream (Click here).

  1. Drive the vehicle in an urban area for approximately 10 minutes.

  1. Read DTCs using the Techstream.

    OK:
    No DTC is output.



NG
REPLACE ECM (Click here)
OK

END