Home › Engine / Hybrid System ยท CRUISE CONTROL › DYNAMIC LASER CRUISE CONTROL SYSTEM

DYNAMIC LASER CRUISE CONTROL SYSTEM > PROBLEM SYMPTOMS TABLE

for Preparation Click here


HINT:
  1. Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
  2. Inspect the fuses and relays related to this system before inspecting the suspected areas below.


Dynamic Laser Cruise Control System 
Symptom
Suspected Area
See page
Main switch cannot be turned on. (CRUISE main indicator light on combination meter does not illuminate.)
Cruise control switch circuit
Click here
CRUISE main indicator light circuit
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 2UZ-FE).
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FE).
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FBE).
Click here
Vehicle speed setting cannot be done. (CRUISE main indicator light on combination meter illuminates when main switch is turned on, but turns off when operating SET function.)
Cruise control switch circuit
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 2UZ-FE).
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FE).
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FBE).
Click here
Vehicle speed setting cannot be done. (CRUISE main indicator light on combination meter illuminates when main switch is turned on, and remains on when operating SET function.)
Cruise control switch circuit
Click here
Stop light switch circuit
Click here
Transmission range sensor circuit (for A750F)
Click here
Transmission range sensor circuit (for A750E)
Click here
Transmission range sensor circuit (for AB60F)
Click here
Transmission range sensor circuit (for AB60E)
Click here
Vehicle speed sensor circuit
Click here
Combination meter system
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 2UZ-FE).
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FE).
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FBE).
Click here
While vehicle is driven with cruise control, the control is canceled. (CRUISE main indicator light remains on.)
Cruise control switch circuit
Click here
Vehicle speed sensor circuit
Click here
Stop light switch circuit
Click here
Combination meter system
Click here
Transmission range sensor circuit (for A750F)
Click here
Transmission range sensor circuit (for A750E)
Click here
Transmission range sensor circuit (for AB60F)
Click here
Transmission range sensor circuit (for AB60E)
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 2UZ-FE).
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FE).
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FBE).
Click here
Hunting (Speed is not constant.)
Vehicle speed sensor circuit
Click here
Malfunction in speed meter circuit
Click here
Laser radar sensor power source circuit
Click here
Distance control ECU power source circuit
Click here
Distance control ECU
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 2UZ-FE).
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FE).
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FBE).
Click here
Vehicle speed setting cannot be canceled. (When coast, acceleration, resume, or set speed change function is operated with control switch.)
Cruise control switch circuit
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 2UZ-FE).
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FE).
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FBE).
Click here
Erroneous detection or lost sight of the vehicle ahead.
Clean laser radar sensor with soft cloth, etc.
-
Improper aiming of sensor beam axis
Click here
Alarm buzzer does not sound.
Skid control buzzer circuit
Click here
VSC system
Click here
Distance control ECU power source circuit
Click here
Distance control ECU
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 2UZ-FE).
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FE).
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FBE).
Click here
Set distance cannot be changed.
Combination meter system
Click here
Distance control switch circuit
Click here
Distance control ECU
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 2UZ-FE)
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FE).
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FBE).
Click here
No information on the display
Combination meter system
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 2UZ-FE)
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FE).
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FBE).
Click here
No brake control (when decelerating)
VSC system
Click here
Distance control ECU power source circuit
Click here
Distance control ECU
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 2UZ-FE)
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FE).
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FBE).
Click here
Constant speed mode cannot be turned on.
Cruise control switch circuit
Click here
Combination meter system
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 2UZ-FE)
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FE).
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FBE).
Click here
Vehicle speed setting cannot be canceled with wiper HI or LO.
Wiper signal circuit
Click here
Distance control ECU
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 2UZ-FE)
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FE).
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FBE).
Click here
Vehicle speed setting is canceled with washer ON.
Washer signal circuit
Click here
Distance control ECU
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 2UZ-FE)
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FE).
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FBE).
Click here
Unable to adjust (complete) beam axis of laser radar sensor.
Check position, distance and angle of reflector
-
Check installation of laser radar sensor
Click here
Laser radar sensor
Click here
Distance control ECU
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 2UZ-FE)
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FE).
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FBE).
Click here
Cannot change from constant speed control mode to vehicle-to-vehicle distance control mode.
Cruise control switch circuit
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 2UZ-FE)
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FE).
Click here
If the symptoms still occur after the above areas have been inspected and have proven to be normal, replace the ECM (for 3UR-FBE).
Click here