TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM > INSPECTION |
| 1. INSPECT INDICATOR LIGHT |
4HI Indicator Light:
Turn the ignition switch to ON.
Change the 4WD control switch from 2WD to 4H. Then move the shift lever to N (vehicle is stopped).
![]() |
Check the 4HI indicator light.
4LO Indicator Light:
Turn the ignition switch to ON.
Change the 4WD control switch from 2WD to 4H. Then move the shift lever to N (vehicle is stopped) after the 4HI indicator light illuminates.
Change the 4WD control switch from 4H to 4L.
![]() |
Check the 4LO indicator light.
CENTER DIFF. Indicator Light:
Turn the ignition switch to ON.
Change the 4WD control switch from 2WD to 4H. Then move the shift lever to N (vehicle is stopped). (4HI indicator light illuminates).
Press the center differential lock switch.
Check the CENTER DIFF. indicator light.

| 2. INSPECT FUSE (4WD) |
![]() |
Remove the 4WD fuse from the main body ECU.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 4WD fuse | Always | Below 1 Ω |
| 3. INSPECT 4WD CONTROL ECU (POWER SUPPLY) |
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A29-3 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A29-4 (GND) - Body ground | Always | Below 1 Ω |
| 4. INSPECT 4WD CONTROL ECU (4WD CONTROL SWITCH) |
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A28-11 (2-4) - Body ground | Ignition switch ON 4WD control switch 2WD | Below 1.5 V |
| Ignition switch ON 4WD control switch 4H | Below 1.5 V | |
| Ignition switch ON 4WD control switch 4L | 10.5 to 14 V | |
| A28-13 (LO) - Body ground | Ignition switch ON 4WD control switch 2WD | 10.5 to 14 V |
| Ignition switch ON 4WD control switch 4H | Below 1.5 V | |
| Ignition switch ON 4WD control switch 4L | Below 1.5 V |
| 5. INSPECT 4WD CONTROL ECU (CENTER DIFFERENTIAL LOCK SWITCH) |
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A28-12 (DL) - Body ground | Ignition switch ON Center differential lock switch ON | Below 1.5 V |
| Ignition switch ON Center differential lock switch OFF | 10.5 to 14 V |
| 6. INSPECT MULTI MODE TRANSFER SHIFT ACTUATOR |
Check the harness and connector (ECU - multi mode transfer shift actuator).
Disconnect the D45 actuator connector.
Disconnect the A28 and A29 ECU connectors.
Measure the resistance according to the value(s) in the table below.

| Tester Connection | Condition | Specified Condition |
| A28-6 (TL1) - D45-4 (TL1) | Always | Below 1 Ω |
| A28-6 (TL1) - Body ground | Always | 10 kΩ or higher |
| A28-7 (TL2) - D45-6 (TL2) | Always | Below 1 Ω |
| A28-7 (TL2) - Body ground | Always | 10 kΩ or higher |
| A28-8 (TL3) - D45-5 (TL3) | Always | Below 1 Ω |
| A28-8 (TL3) - Body ground | Always | 10 kΩ or higher |
| A28-14 (4WD) - D45-3 (CDL) | Always | Below 1 Ω |
| A28-14 (4WD) - Body ground | Always | 10 kΩ or higher |
| A29-7 (TM2) - D45-2 (TM2) | Always | Below 1 Ω |
| A29-7 (TM2) - Body ground | Always | 10 kΩ or higher |
| A29-8 (TM1) - D45-1 (TM1) | Always | Below 1 Ω |
| A29-8 (TM1) - Body ground | Always | 10 kΩ or higher |
| D45-7 (GND1) - Body ground | Always | Below 1 Ω |
Check the 4WD control ECU (multi mode transfer shift actuator).
Connect the A28 and A29 ECU connectors.
Connect the D45 actuator connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A29-8 (TM1) - A29-4 (GND) | Ignition switch ON 4WD control switch 2WD → 4H or 4L (During operation of Multi mode transfer shift actuator motor from 2WD to 4WD HIGH or 4WD LOW) | 10 to 14 V |
| Ignition switch ON 4WD control switch 2WD → 4H or 4L (Multi mode transfer shift actuator motor stopped) | Below 1.5 V | |
| A29-7 (TM2) - A29-4 (GND) | Ignition switch ON 4WD control switch 4H or 4L → 2WD (During operation of Multi mode transfer shift actuator motor from 4WD HIGH or 4WD LOW to 2WD) | 10 to 14 V |
| Ignition switch ON 4WD control switch 4H or 4L → 2WD (Multi mode transfer shift actuator motor stopped) | Below 1.5 V | |
| A28-6 (TL1) - A29-4 (GND) | Ignition switch ON 4WD control switch 2WD | Below 1.5 V |
| Ignition switch ON 4WD control switch 4H or 4L | 10.5 to 14 V | |
| A28-7 (TL2) - A29-4 (GND) | Ignition switch ON 4WD control switch 2WD | 10.5 to 14 V |
| Ignition switch ON 4WD control switch 4H or 4L Center differential Lock | 10.5 to 14 V | |
| Ignition switch ON 4WD control switch 4H or 4L Center differential Free | Below 1.5 V | |
| A28-8 (TL3) - A29-4 (GND) | Ignition switch ON 4WD control switch 2WD | 10.5 to 14 V |
| Ignition switch ON 4WD control switch 4H or 4L Center differential Lock | Below 1.5 V | |
| Ignition switch ON 4WD control switch 4H or 4L Center differential Free | 10.5 to 14 V | |
| A28-14 (4WD) - A29-4 (GND) | Ignition switch ON 4WD control switch 2WD | 9.5 to 14 V |
| Ignition switch ON 4WD control switch 4H or 4L Center differential Lock | Below 1.5 V | |
| Ignition switch ON 4WD control switch 4H or 4L Center differential Free | 9.5 to 14 V |
Check the 4WD control ECU.
Disconnect the D45 actuator connector.
Connect the A28 and A29 ECU connectors.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D45-3 (CDL) - D45-7 (GND1) | Ignition switch ON | 9.5 to 14 V |
| D45-4 (TL1) - D45-7 (GND1) | Ignition switch ON | 10.5 to 14 V |
| D45-6 (TL2) - D45-7 (GND1) | Ignition switch ON | 10.5 to 14 V |
| D45-5 (TL3) - D45-7 (GND1) | Ignition switch ON | 10.5 to 14 V |
Inspect the multi mode transfer shift actuator.
Remove the transfer shift actuator (Click here).
Check the 2WD to 4WD HIGH (H4L) switch.
Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the 2WD to 4WD HIGH (H4L) position.

| Tester Connection | Condition | Specified Condition |
| 3 (CDL) - 7 (GND1) | After 2WD to 4WD HIGH (H4F) switch is complete | 100 kΩ or higher |
| 4 (TL1) - 7 (GND1) | After 2WD to 4WD HIGH (H4F) switch is complete | 100 kΩ or higher |
| 5 (TL3) - 7 (GND1) | After 2WD to 4WD HIGH (H4F) switch is complete | 100 kΩ or higher |
| 6 (TL2) - 7 (GND1) | After 2WD to 4WD HIGH (H4F) switch is complete | Below 1 Ω |
Check the 4WD HIGH (H4F) to 2WD switch.
Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the 4WD HIGH (H4F) to 2WD position.

| Tester Connection | Condition | Specified Condition |
| 3 (CDL) - 7 (GND1) | After 4WD HIGH (H4F) to 2WD switch is complete | 100 kΩ or higher |
| 4 (TL1) - 7 (GND1) | After 4WD HIGH (H4F) to 2WD switch is complete | Below 1 Ω |
| 5 (TL3) - 7 (GND1) | After 4WD HIGH (H4F) to 2WD switch is complete | 100 kΩ or higher |
| 6 (TL2) - 7 (GND1) | After 4WD HIGH (H4F) to 2WD switch is complete | 100 kΩ or higher |
| 7. INSPECT A.D.D. ACTUATOR |
Check the harness and connector (ECU - A.D.D. actuator).
Disconnect the A28 and A29 ECU connectors.
Disconnect the F1 actuator connector.
Measure the resistance according to the value(s) in the table below.

| Tester Connection | Condition | Specified Condition |
| A28-9 (DL1) - F1-6 (DL1) | Always | Below 1 Ω |
| A28-9 (DL1) - Body ground | Always | 100 kΩ or higher |
| A28-10 (DL2) - F1-5 (DL2) | Always | Below 1 Ω |
| A28-10 (DL2) - Body ground | Always | 100 kΩ or higher |
| A28-15 (ADD) - F1-3 (ADD) | Always | Below 1 Ω |
| A28-15 (ADD) - Body ground | Always | 100 kΩ or higher |
| A29-1 (DM1) - F1-1 (DM1) | Always | Below 1 Ω |
| A29-1 (DM1) - Body ground | Always | 100 kΩ or higher |
| A29-5 (DM2) - F1-2 (DM2) | Always | Below 1 Ω |
| A29-5 (DM2) - Body ground | Always | 100 kΩ or higher |
| F1-4 (GND) - Body ground | Always | Below 1 Ω |
Check the 4WD control ECU (A.D.D. actuator).
Connect the A28 and A29 ECU connectors.
Connect the F1 actuator connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A29-1 (DM1) - A29-4 (GND) | Ignition switch ON 4WD control switch 4H (During operation of A.D.D. actuator from Lock to Free) | 10 to 14 V |
| Ignition switch ON 4WD control switch 4H (A.D.D. actuator Free) | Below 1.5 V | |
| A29-5 (DM2) - A29-4 (GND) | Ignition switch ON 4WD control switch 4H (during operation of A.D.D. actuator from Free to Lock) | 10 to 14 V |
| Ignition switch ON 4WD control switch 4H (A.D.D. actuator Lock) | Below 1.5 V | |
| A28-9 (DL1) - A29-4 (GND) | Ignition switch ON 4WD control switch 2WD (A.D.D. actuator Free) | 10.5 to 14 V |
| Ignition switch ON 4WD control switch 4H (A.D.D. actuator Lock) | Below 1.5 V | |
| A28-10 (DL2) - A29-4 (GND) | Ignition switch ON 4WD control switch 2WD (A.D.D. actuator Free) | Below 1.5 V |
| Ignition switch ON 4WD control switch 4H (A.D.D. actuator Lock) | 10.5 to 14 V | |
| A28-15 (ADD) - A29-4 (GND) | Ignition switch ON 4WD control switch 2WD | 10 to 14 V |
| Ignition switch ON 4WD control switch 4H or 4L | Below 1.5 V |
Check the 4WD control ECU.
Connect the A28 and A29 ECU connectors.
Disconnect the F1 actuator connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F1-3 (ADD) - F1-4 (GND) | Ignition switch ON | 10 to 14 V |
| F1-5 (DL2) - F1-4 (GND) | Ignition switch ON | 10.5 to 14 V |
| F1-6 (DL1) - F1-4 (GND) | Ignition switch ON | 10.5 to 14 V |
Inspect the A.D.D. actuator.
Remove the A.D.D. actuator (Click here).
Check the Free to Lock switch.
Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the Free to the Lock position.

| Tester Connection | Condition | Specified Condition |
| 3 (ADD) - 4 (GND) | After Free to Lock switch is complete | Below 1 Ω |
| 5 (DL2) - 4 (GND) | After Free to Lock switch is complete | 100 kΩ or higher |
| 6 (DL1) - 4 (GND) | After Free to Lock switch is complete | Below 1 Ω |
Check the Lock to Free switch.
Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the Lock to the Free position.

| Tester Connection | Condition | Specified Condition |
| 3 (ADD) - 4 (GND) | After Lock to Free switch is complete | 100 kΩ or higher |
| 5 (DL2) - 4 (GND) | After Lock to Free switch is complete | Below 1 Ω |
| 6 (DL1) - 4 (GND) | After Lock to Free switch is complete | 100 kΩ or higher |
| 8. INSPECT HIGH-LOW TRANSFER SHIFT ACTUATOR |
Check the harness and connector (ECU - high-low transfer shift actuator).
Disconnect the D46 high-low transfer shift actuator connector.
Disconnect the A28 and A29 ECU connector.
Measure the resistance according to the value(s) in the table below.

| Tester Connection | Condition | Specified Condition |
| A28-1 (HL1) - D46-4 (HL1) | Always | Below 1 Ω |
| A28-1 (HL1) - Body ground | Always | 100 kΩ or higher |
| A28-2 (HL2) - D46-6 (HL2) | Always | Below 1 Ω |
| A28-2 (HL2) - Body ground | Always | 100 kΩ or higher |
| A28-3 (HL3) - D46-5 (HL3) | Always | Below 1 Ω |
| A28-3 (HL3) - Body ground | Always | 100 kΩ or higher |
| A28-16 (NP) - D46-3 (N) | Always | Below 1 Ω |
| A28-16 (NP) - Body ground | Always | 100 kΩ or higher |
| A29-2 (HM1) - D46-1 (HM1) | Always | Below 1 Ω |
| A29-2 (HM1) - Body ground | Always | 100 kΩ or higher |
| A29-6 (HM2) - D46-2 (HM2) | Always | Below 1 Ω |
| A29-6 (HM2) - Body ground | Always | 100 kΩ or higher |
| D46-7 (GND) - Body ground | Always | Below 1 Ω |
Check the 4WD control ECU (high-low transfer shift actuator).
Connect the A28 and A29 ECU connectors.
Connect the D46 actuator connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A29-6 (HM2) - A29-4 (GND) | Ignition switch ON 4WD control switch 4H → 4L (During operation of high-low transfer shift actuator motor from 4WD HIGH to 4WD LOW) | 10 to 14 V |
| Ignition switch ON 4WD control switch 4H → 4L (High-low transfer shift actuator motor stopped) | Below 1.5 V | |
| A29-2 (HM1) - A29-4 (GND) | Ignition switch ON 4WD control switch 4L → 4H (During operation of high-low transfer shift actuator motor from 4WD LOW to 4WD HIGH) | 10 to 14 V |
| Ignition switch ON 4WD control switch 4L → 4H (High-low transfer shift actuator motor stopped) | Below 1.5 V | |
| A28-1 (HL1) - A29-4 (GND) | Ignition switch ON 4WD control switch 4H | Below 1.5 V |
| Ignition switch ON 4WD control switch 4L | 10.5 to 14 V | |
| A28-2 (HL2) - A29-4 (GND) | Ignition switch ON 4WD control switch 4H | 10.5 to 14 V |
| Ignition switch ON 4WD control switch 4L | Below 1.5 V | |
| A28-3 (HL3) - A29-4 (GND) | Ignition switch ON 4WD control switch 4H | 10.5 to 14 V |
| Ignition switch ON 1.5 seconds or less after 4WD HIGH to 4WD LOW switching operation | Below 1.5 V | |
| Ignition switch ON Over 1.5 seconds after 4WD HIGH to 4WD LOW switching operation | 10.5 to 14 V | |
| A28-16 (NP) - A29-4 (GND) | Ignition switch ON 1.5 seconds or less after 4WD HIGH to 4WD LOW switching operation | Below 1.5 V |
| Ignition switch ON Over 1.5 seconds after 4WD HIGH to 4WD LOW switching operation | 10 to 14 V |
Check the 4WD control ECU.
Connect the A28 and A29 ECU connectors.
Disconnect the D46 actuator connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D46-3 (N) - D46-7 (GND) | Ignition switch ON | 10 to 14 V |
| D46-4 (HL1) - D46-7 (GND) | Ignition switch ON | 10.5 to 14 V |
| D46-5 (HL3) - D46-7 (GND) | Ignition switch ON | 10.5 to 14 V |
| D46-6 (HL2) - D46-7 (GND) | Ignition switch ON | 10.5 to 14 V |
Inspect the high-low transfer shift actuator.
Remove the transfer shift actuator (Click here).
Check the 4WD HIGH to 4WD LOW switch.
Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the 4WD HIGH to 4WD LOW position.

| Tester Connection | Condition | Specified Condition |
| 3 (N) - 7 (GND) | After 4WD HIGH to 4WD LOW switch is complete | 100 kΩ or higher |
| 4 (HL1) - 7 (GND) | After 4WD HIGH to 4WD LOW switch is complete | 100 kΩ or higher |
| 5 (HL3) - 7 (GND) | After 4WD HIGH to 4WD LOW switch is complete | 100 kΩ or higher |
| 6 (HL2) - 7 (GND) | After 4WD HIGH to 4WD LOW switch is complete | Below 1 Ω |
Check the 4WD LOW to 4WD HIGH switch.
Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the 4WD LOW to 4WD HIGH position.

| Tester Connection | Condition | Specified Condition |
| 3 (N) - 7 (GND) | After 4WD LOW to 4WD HIGH switch is complete | 100 kΩ or higher |
| 4 (HL1) - 7 (GND) | After 4WD LOW to 4WD HIGH switch is complete | Below 1 Ω |
| 5 (HL3) - 7 (GND) | After 4WD LOW to 4WD HIGH switch is complete | 100 kΩ or higher |
| 6 (HL2) - 7 (GND) | After 4WD LOW to 4WD HIGH switch is complete | 100 kΩ or higher |