Home › Engine / Hybrid System › 3UR-FBE ENGINE MECHANICAL › ENGINE UNIT
RM27L0U _51 Engine / Hybrid System _049295 3UR-FBE ENGINE MECHANICAL _0235555 ENGINE UNIT A

3UR-FBE ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


PROCEDURE

Hide 1.REMOVE ENGINE WIRE

A259649

a.

Disconnect the 2 camshaft timing control valve connectors.


b.

Disconnect the 4 ignition coil connectors.


c.

Disconnect the 2 VVT sensor connectors.


d.

Disconnect the camshaft position sensor connector.


e.

Disconnect the vacuum switching valve connector (for ACIS).


f.

Disconnect the purge VSV connector.


g.

Disconnect the engine coolant temperature sensor connector.


h.

Disconnect the fuel injector connector.


i.

Remove the bolt and disconnect the 8 clamps.


j.
A259654

Disconnect the 2 camshaft timing control valve connectors.


k.

Disconnect the 4 ignition coil connectors.


l.

Disconnect the 2 VVT sensor connectors.


m.

Disconnect the fuel injector connector.


n.

Disconnect the throttle sensor connector.


o.

Disconnect the oil pressure sender gauge connector.


p.

Disconnect the 9 clamps.


q.
A259651

Disconnect the 3 connectors.


r.

Disconnect the 5 clamps.


s.

Remove the 3 bolts.


t.

Remove the engine wire.


Hide 23801P 2.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

A308965

a.

Remove the No. 1 fuel pipe (See page Engine / Hybrid System>3UR-FBE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 11415A 3.REMOVE CYLINDER BLOCK WATER DRAIN COCK PLUG

A163838E01
0.081,0.108 0.376,0.319 0.295,0.211 10 RH: 0.081,1.779 0.404,1.990 0.323,0.211 10 LH:

a.

Remove the 2 water drain cock plugs from the water drain cocks.


b.

Remove the 2 water drain cocks from the cylinder block.


Hide 12361 4.REMOVE FRONT ENGINE MOUNTING INSULATOR

a.
A163786

Remove the nut and mounting insulator.


Hide 12362A 5.REMOVE FRONT ENGINE MOUNTING INSULATOR LH

a.
A163787

Remove the nut and mounting insulator.


Hide 12311 6.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH

A160649

a.

Remove the 4 bolts and mounting bracket.


Hide 12315 7.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

A160648

a.

Remove the 4 bolts and mounting bracket.


Hide 12601B 8.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 23902 10.DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY

Hide 23901 11.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide 23807 12.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23808 13.REMOVE NO. 2 FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 44763A 15.REMOVE NO. 1 HOSE TO HOSE TUBE

A163943

a.

Remove the 2 bolts and No. 1 tube.


Hide 23902 17.REMOVE NO. 2 FUEL TUBE SUB-ASSEMBLY

A256359

a.

Remove the 2 bolts and No. 2 fuel tube.


Hide 23901 18.REMOVE FUEL TUBE SUB-ASSEMBLY

A256360

a.

Remove the fuel tube.


Hide 16261G 20.REMOVE NO. 1 WATER BY-PASS HOSE

Hide 16355 21.REMOVE FRONT WATER BY-PASS JOINT

Hide 17303 24.SEPARATE AIR PIPE SUB-ASSEMBLY

Hide 16206 25.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16603 27.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 16211 28.REMOVE FLUID COUPLING BRACKET

Hide 16620 29.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 83520 30.REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY

Hide 17303 31.REMOVE AIR PIPE SUB-ASSEMBLY

Hide 16323 32.REMOVE WATER INLET HOUSING

Hide 82121 36.REMOVE ENGINE WIRE

A306987

a.

Disconnect the 4 knock sensor connectors.


b.

Disconnect the 3 clamps. Then remove the engine wire.


Hide 12215 37.REMOVE CASE SEPARATOR

a.
A306989

Slide the 2 clips and remove the No. 9 water by-pass hose and No. 10 water by-pass hose from the case separator.


b.
A306988

Remove the 4 bolts and case separator.