Home › Engine / Hybrid System › 3UR-FBE ENGINE MECHANICAL › ENGINE UNIT
RM27L0U _51 Engine / Hybrid System _049295 3UR-FBE ENGINE MECHANICAL _0235555 ENGINE UNIT A

3UR-FBE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STUD BOLT

A163193E02
1.889,2.238 3.144,2.426 1.254,0.188 10 24.5 mm (0.965 in.) 1.594,2.951 2.787,3.139 1.193,0.188 10 40 mm (1.58 in.) 1.883,2.538 3.061,2.726 1.178,0.188 10 14 mm (0.551 in.) 1.316,2.8 1.717,2.33 1.717,2.33 1.85,2.33 false 1.316,3.153 1.746,2.639 1.746,2.639 1.861,2.639 false

a.

Install the timing chain cover stud bolt.

i.

Using an E10 "TORX" socket wrench, install the 2 stud bolts as shown in the illustration.

Torque:
20 N*m (204 kgf*cm, 16 ft.*lbf)



b.
A178526E02
2.281,3.76 2.448,3.906 2.448,3.906 2.448,4.01 false 1.917,2.979 2.063,2.979 2.063,2.979 2.281,3.438 false 0.656,3.708 0.802,3.771 false 0.656,3.365 0.802,3.427 0.802,3.427 0.802,3.958 false 1.427,0.146 1.573,0.333 0.146,0.188 10 false A 0.167,1.229 0.313,1.417 0.146,0.188 10 false A 2.125,2.25 2.302,2.458 0.177,0.208 10 false B 0.271,3.969 1.417,4.167 1.146,0.198 10 false 9 mm (0.354 in.) 0.969,3.292 1.677,3.729 0.708,0.438 10 false 19 mm (0.748 in.) 1.917,4 3.063,4.198 1.146,0.198 10 false 12 mm (0.472 in.) 0.5,2.896 1.677,3.156 1.177,0.26 10 false 22 mm (0.866 in.) 2.615,3.292 3.271,3.688 0.656,0.396 10 false 39 mm (1.54 in.) 0.271,2.573 0.469,2.771 0.198,0.198 10 false A: 1.896,2.573 2.063,2.771 0.167,0.198 10 false B:

Install the oil pan stud bolt.

i.

Using an E6 and E7 "TORX" socket wrench, install the 3 stud bolts as shown in the illustration.

Torque:
for stud bolt A : 5.0 N*m (51 kgf*cm, 44 in.*lbf)
for stud bolt B : 9.0 N*m (92 kgf*cm, 80 in.*lbf)



Hide 2.INSTALL RING PIN

A160726E01
0.367,1.451 0.506,1.622 0.140,0.171 10 A 0.578,1.945 0.718,2.116 0.140,0.171 10 A 2.786,1.434 2.913,1.599 0.127,0.165 10 B 2.811,1.832 2.938,2.000 0.127,0.168 10 B 0.837,2.75 1.750,2.934 0.913,0.184 10 7.5 to 8.5 mm 2.329,2.613 3.221,2.797 0.892,0.184 10 3.6 to 4.6 mm 0.213,2.335 0.385,2.506 0.172,0.171 10 A: 1.668,2.335 1.823,2.500 0.155,0.165 10 B:

a.

Using a plastic-faced hammer, tap in new ring pins to the timing chain cover.

Standard Protrusion:
Item Ring Pin Diameter Specified Condition
Ring pin A 13 mm (0.512 in.) 7.5 to 8.5 mm (0.295 to 0.335 in.)
Ring pin B 11 mm (0.433 in.) 3.6 to 4.6 mm (0.142 to 0.181 in.)



Hide 11381A 3.INSTALL ENGINE REAR OIL SEAL

a.

Apply MP grease to the lip of a new oil seal.


b.
A148433E02
0.067,0.812 0.434,1.054 0.367,0.242 10 SST 0.708,0.89 0.708,1.494 0.708,1.494 1.029,1.494 false 0.455,0.89 1.142,0.89 false

Using SST, tap in the oil seal until its surface is flush with the oil seal retainer edge.

SST
09223-15030  
09950-70010  (09951-07100)

Standard depth:

0 to 1.0 mm (0 to 0.0394 in.)


NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap on the oil seal at an angle.




Hide 12109A 4.INSTALL OIL DRAIN PIPE SUB-ASSEMBLY

A160728

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the drain pipe.


c.

Install the oil drain pipe with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11381 5.INSTALL ENGINE REAR OIL SEAL RETAINER

A148434E10
1.833,0.438 1.875,0.156 1.875,0.156 2.031,0.156 false 0.448,1.792 0.365,1.469 false 3.135,1.781 3.052,1.458 false 2.083,0.052 3.063,0.229 0.979,0.177 10 false 2.0 to 3.0 mm 0.25,1.813 0.802,2 0.552,0.188 10 false 3.5 mm 2.854,1.813 3.406,2 0.552,0.188 10 false 3.5 mm

a.

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal diameter:

2.0 to 3.0 mm (0.0787 to 0.118 in.)


Application position from inside edge of retainer:

3.5 mm (0.138 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.




b.
A145612

Install the oil seal retainer with the 6 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

Do not start the engine for at least 2 hours after installing.

·

When installing the oil seal retainer, make sure the lip of the oil seal is not damaged.

·

When installing the oil seal retainer, make sure the lip of the oil seal is not folded incorrectly.




Hide 15104 6.INSTALL OIL STRAINER SUB-ASSEMBLY

A160724

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the oil strainer.


c.

Install the oil strainer with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Make sure the O-ring is not twisted or damaged.



Hide 12121 7.INSTALL NO. 1 OIL PAN BAFFLE PLATE

A160723

a.

Install the baffle plate with the 7 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12101 8.INSTALL OIL PAN SUB-ASSEMBLY

A160729E06
0.719,0.771 0.938,0.135 0.938,0.135 1.094,0.135 false 1.146,0.052 2.417,0.49 1.271,0.438 10 true 3.0 to 4.0 mm

a.

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.




b.
A160721E06
3.094,1.063 3.229,1.219 0.135,0.156 10 false A 2.313,1.781 2.448,1.938 0.135,0.156 10 true B 2.99,1.427 3.24,1.583 0.25,0.156 10 false Nut 1.146,0.813 1.417,1.146 0.271,0.333 10 true Nut 3.083,0.698 3.219,0.854 0.135,0.156 10 false A 1.875,1.823 2.01,1.979 0.135,0.156 10 true B 1.479,1.833 1.615,1.99 0.135,0.156 10 true B 1.188,1.833 1.323,1.99 0.135,0.156 10 true B 0.896,1.792 1.031,1.948 0.135,0.156 10 true B 0.302,1.458 0.438,1.615 0.135,0.156 10 false B 2.99,0.26 3.125,0.417 0.135,0.156 10 false B 2.219,0.021 2.354,0.177 0.135,0.156 10 false B 1.875,0.021 2.01,0.177 0.135,0.156 10 false B 1.438,0.031 1.573,0.188 0.135,0.156 10 true B 0.979,0.031 1.115,0.188 0.135,0.156 10 false B 0.292,0.26 0.427,0.417 0.135,0.156 10 false B

Install the oil pan with the 14 bolts and 2 nuts.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B : 35 N*m (357 kgf*cm, 26 ft.*lbf)
for nut : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not start the engine for at least 2 hours after installing.



Hide 12102A 9.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

A160730E01
0.516,0.049 2.388,0.232 1.872,0.184 10 Seal diameter: 3.0 to 4.0 mm

a.

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.156 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.




b.
A160720E03
2.885,0.531 3.156,0.708 0.271,0.177 10 false Nut 1.448,1.698 1.719,1.875 0.271,0.177 10 true Nut

Install the oil pan with the 14 bolts and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Do not start the engine for at least 2 hours after installing.



Hide 16877 10.INSTALL NO. 1 HEAT EXCHANGER COVER

A161918E01
0.671,0.002 2.533,0.193 1.863,0.191 10 Seal diameter: 3.0 to 4.0 mm

a.

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the No. 1 heat exchanger cover within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.




b.
A161916E05
2.448,1.75 2.688,1.896 0.24,0.146 9 true Nut 0.646,1.896 0.885,2.042 0.24,0.146 9 true Nut 0.771,0.219 0.906,0.385 0.135,0.167 10 true A 0.49,1.438 0.625,1.604 0.135,0.167 10 true B 3.156,1.573 3.292,1.74 0.135,0.167 10 false C 1.188,0.115 1.323,0.281 0.135,0.167 10 true A 1.729,0.115 1.865,0.281 0.135,0.167 10 true A 2.125,0.094 2.26,0.26 0.135,0.167 10 true A 2.594,0.135 2.729,0.302 0.135,0.167 10 true A 2.99,0.333 3.125,0.5 0.135,0.167 10 true A 1.052,1.885 1.188,2.052 0.135,0.167 10 true A 1.635,1.885 1.771,2.052 0.135,0.167 10 true A 1.979,1.885 2.115,2.052 0.135,0.167 10 true A 3.292,0.979 3.427,1.146 0.135,0.167 10 false A

Install the heat exchanger cover with the 12 bolts and 2 nuts.

Torque:
for bolt C : 10 N*m (102 kgf*cm, 7 ft.*lbf)
except bolt C : 21 N*m (214 kgf*cm, 15 ft.*lbf)

Standard Bolt:
Item Length Thread Diameter
Bolt A 20 mm (0.787 in.) 8 mm (0.315 in.)
Bolt B 70 mm (2.76 in.) 8 mm (0.315 in.)
Bolt C 16 mm (0.630 in.) 6 mm (0.236 in.)


NOTICE:

Do not start the engine for at least 2 hours after installing.



Hide 12203A 11.INSTALL VENTILATION PIPE GASKET

A163596E03
1.344,1.271 0.896,1.448 0.896,1.448 1.333,1.521 true 0.51,1.396 0.802,1.583 0.292,0.188 10 true SST

a.

Using SST, evenly tap in a new ventilation pipe gasket until its surface is flush with the lip of the ventilation pipe.

SST
09950-60010  (09951-00360)
09950-70010  (09951-07100)

NOTICE:
·

Do not tap the gasket at an angle.

·

Do not tap the gasket excessively.




Hide 11445 12.INSTALL CYLINDER BLOCK WATER JACKET SPACER

A161997E03
0.073,0.13 0.492,0.608 0.419,0.478 10 UP Mark 0.374,0.204 1.315,0.204 1.315,0.204 2.512,0.73 false 0.768,0.934 0.768,0.204 false

a.

Install the 2 water jacket spacers as shown in the illustration.

NOTICE:
·

Face the cutouts indicated by the arrows in illustration away from the engine.

·

Face the "up mark" as shown in the illustration.




Hide 13801 19.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 11103C 21.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH

Hide 11104A 23.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH

Hide 13521A 24.INSTALL CRANKSHAFT TIMING GEAR KEY

A164296

a.

Install the timing gear key.

HINT:

The other timing gear key will be installed at a later step.



Hide 13550 25.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

Hide 13506 26.INSTALL CHAIN SUB-ASSEMBLY (for RH Side)

Hide 13561 27.INSTALL NO. 1 CHAIN VIBRATION DAMPER (for RH Side)

Hide 13559 28.INSTALL CHAIN TENSIONER SLIPPER (for RH Side)

Hide 13540 29.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY (for RH Side)

Hide 13560A 30.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY

Hide 13506 31.INSTALL CHAIN SUB-ASSEMBLY (for LH Side)

Hide 13559 32.INSTALL CHAIN TENSIONER SLIPPER (for LH Side)

Hide 13540 33.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY (for LH Side)

Hide 13561 34.INSTALL NO. 1 CHAIN VIBRATION DAMPER (for LH Side)

Hide 13050 35.TIGHTEN CAMSHAFT TIMING GEAR ASSEMBLY (for LH Side)

Hide 13050 36.TIGHTEN CAMSHAFT TIMING GEAR ASSEMBLY (for RH Side)

Hide 37.CHECK NO. 1 CYLINDER TO TDC / COMPRESSION

Hide 11302 39.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 16100 40.INSTALL ENGINE WATER PUMP ASSEMBLY

Hide 11301C 41.INSTALL TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL

a.
A163995E05
1.771,2.635 1.854,3.01 false 1.854,3.01 1.927,2.604 false 1.688,3.031 2.01,3.208 0.323,0.177 10 true SST

Apply MP grease to the lip of a new oil seal.


b.

Using SST and a hammer, tap in the oil seal to a depth between 0 to 1.0 mm (0 to 0.0394 in.) from the timing chain cover edge.

SST
09223-22010  
09506-35010  

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap oil seal at an angle.




Hide 13521A 42.INSTALL CRANKSHAFT TIMING GEAR KEY

a.
A163993

Install the crankshaft timing gear key to the crankshaft.


Hide 11193 43.INSTALL SPARK PLUG TUBE GASKET

A380019E01
0.552,1.885 2.844,2.083 2.292,0.198 10 false Area to cut off

a.

Using a cutter knife, cut off the seal part of the removed gasket.


b.
A164316E03
1.167,0.583 1.271,0.333 1.271,0.333 1.396,0.333 true 1.688,1.156 1.688,1.5 true 1.448,0.271 2.615,0.5 1.167,0.229 10 false Removed Gasket 1.333,1.583 2.188,1.792 0.854,0.208 10 false New Gasket

Using the removed gasket and a hammer, tap in a new gasket until it stops.

HINT:

If the removed gasket does not fit on the new one, correct the removed one with pliers.



c.

Apply a light coat of MP grease to the gasket lip.


d.

Return the 4 ventilation baffle plate claws to the original positions.


Hide 15678E 44.INSTALL OIL CONTROL VALVE FILTER LH

a.
A164313E10
2.49,0.885 2.49,1.302 false 2.802,0.125 2.958,0.125 2.958,0.125 3.115,0.906 false 1.708,0.396 2.167,0.396 2.167,0.396 2.813,0.813 true 2.313,1.313 2.708,1.552 0.396,0.24 10 false Filter 1.198,0.323 1.74,0.51 0.542,0.188 10 true Gasket 1.052,0.052 2.906,0.26 1.854,0.208 10 true Cylinder Head Cover Spacer

Install the valve filter in the cylinder head cover.


b.

Install a new gasket and the cylinder head cover spacer with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15678D 45.INSTALL OIL CONTROL VALVE FILTER RH

a.
A164314E08
0.917,0.781 0.917,1.208 false 0.281,0.792 0.635,0.115 0.635,0.115 0.771,0.115 true 0.625,0.688 0.99,0.406 0.99,0.406 1.917,0.406 true 0.75,1.271 1.125,1.479 0.375,0.208 10 false Filter 1.958,0.323 2.458,0.531 0.5,0.208 10 true Gasket 0.802,0.042 2.656,0.25 1.854,0.208 10 true Cylinder Head Cover Spacer

Install the valve filter in the cylinder head cover.


b.

Install a new gasket and the cylinder head cover spacer with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11202 46.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 11201 47.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 15340 48.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY LH

a.
A161909

Apply a light coat of engine oil to 2 new O-rings.


b.

Install the 2 O-rings to the 2 oil control valves.


c.

Install the 2 oil control valves with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15330B 49.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY RH

a.
A161910

Apply a light coat of engine oil to 2 new O-rings.


b.

Install the 2 O-rings to the 2 oil control valves.


c.

Install the 2 oil control valves with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11401G 50.INSTALL CRANKSHAFT POSITION SENSOR

A161908

a.

Install the crankshaft position sensor with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 19312 51.INSTALL CRANK POSITION SENSOR PROTECTOR

A161907

a.

Install the sensor protector with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11102A 52.INSTALL CAMSHAFT POSITION SENSOR

A161906

a.

Install the camshaft position sensor with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11102A 53.INSTALL VVT SENSOR (for Bank 1)

a.
A161904

Install the 2 VVT sensors with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11102A 54.INSTALL VVT SENSOR (for Bank 2)

a.
A161905

Install the 2 VVT sensors with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12185 55.INSTALL OIL FILLER CAP HOUSING

a.
A161917

Align the protrusion of a new gasket with the cutout of the oil filler cap housing, and install the gasket to the housing.


b.
A161903

Install the cap housing with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12108 56.INSTALL OIL FILLER CAP SUB-ASSEMBLY