Home › Engine / Hybrid System › 3UR-FE COOLING › WATER PUMP
RM27L0U _51 Engine / Hybrid System _049304 3UR-FE COOLING _0235618 WATER PUMP A

3UR-FE COOLING  WATER PUMP  INSTALLATION  


PROCEDURE

Hide 16100 1.INSTALL ENGINE WATER PUMP ASSEMBLY

a.
A151828E04
1.938,0.042 2.052,0.188 0.115,0.146 10 false A 1.396,0.031 1.542,0.177 0.146,0.146 10 true A 2.521,1.604 2.635,1.75 0.115,0.146 10 false B 2.302,0.031 2.427,0.188 0.125,0.156 10 false C 3.021,1.365 3.146,1.5 0.125,0.135 10 false C 2.323,1.969 2.448,2.125 0.125,0.156 10 true C 0.281,0.854 0.406,1.031 0.125,0.177 10 false C 0.615,1.927 0.76,2.104 0.146,0.177 10 true C

Install a new gasket and the engine water pump with the 8 bolts shown in the illustration.

·

Bolt A


Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)

·

Bolt B


Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)

·

Bolt C


Torque:
20 N*m (204 kgf*cm, 16 ft.*lbf)


Hide 16173 2.INSTALL WATER PUMP PULLEY

a.
A151837E02
0.347,1.797 0.636,1.946 0.289,0.149 10 SST 1.497,1.654 0.848,1.887 0.848,1.887 0.742,1.887 false

Temporarily install the pulley with the 4 bolts.


b.

Using SST, hold the pulley and tighten the 4 bolts.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
21 N*m (214 kgf*cm, 16 ft.*lbf)


Hide 16323 3.INSTALL INLET WATER HOUSING

a.
A162555E07
0.488,0.138 0.709,0.327 0.221,0.189 10 *1 0.729,0.228 0.789,0.228 false 0.789,0.228 1.21,0.79 false

Install a new gasket to the water pump.

Text in Illustration
*1 Gasket


b.
A183227E02
0.853,1.099 1.164,1.252 0.312,0.153 10 45° 1.127,1.191 1.348,1.333 0.221,0.142 10 *a

Connect the No. 3 water by-pass hose to the inlet water housing.

Text in Illustration
*a Front


c.

Install the inlet water housing with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 16 ft.*lbf)

HINT:

Install the hose so that the direction of the hose clamp is as indicated in the illustration.



Hide 16281F 4.CONNECT NO. 5 WATER BY-PASS HOSE

Hide 17342 6.CONNECT NO. 2 AIR INJECTION SYSTEM HOSE

Hide 17343 7.CONNECT NO. 3 AIR INJECTION SYSTEM HOSE

Hide 16268A 8.CONNECT WATER BY-PASS PIPE HOSE (w/ Trailer Towing System)

Hide 16261G 9.INSTALL NO. 1 WATER BY-PASS HOSE

a.

Install the No. 1 water by-pass hose to the water by-pass joint and water inlet housing.


Hide 16572 12.CONNECT OUTLET RADIATOR HOSE

Hide 17880 13.INSTALL AIR CLEANER HOSE ASSEMBLY

A198568E02
0.149,0.664 0.471,0.814 0.322,0.150 10 90° 0.474,0.32 0.700,0.474 0.226,0.154 10 *a 0.842,0.889 1.102,1.032 0.259,0.143 10 *b

Text in Illustration
*a Top
*b RH

a.

Connect the air cleaner hose and tighten clamp.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.

Connect the No. 2 ventilation hose with the clamp.

HINT:

Install the hose so that the direction of the hose clamp is as indicated in the illustration.



c.

Connect the vacuum hose.


Hide 17700 14.INSTALL AIR CLEANER ASSEMBLY

a.
A299493E02
0.802,1.375 0.802,1.823 true 0.854,3.667 0.854,4.115 true 0.708,1.854 0.896,2.042 0.188,0.188 10 true *1 0.125,2.458 0.396,2.719 0.271,0.26 10 true *B 0.156,0.135 0.427,0.396 0.271,0.26 10 true *A 0.771,4.146 1,4.344 0.229,0.198 10 true *1

Attach grommet to air cleaner before mounting the air cleaner.

Text in Illustration
*A for Type A
*B for Type B
*1 Grommet


b.

Insert the air cleaner into the fender apron hole, and fully insert pin to grommet.


c.

Install the air cleaner with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.

Connect the connector and install the clamp and wire harness.


e.

Connect the air cleaner hose and tighten the clamp.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)