Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC LASER CRUISE CONTROL SYSTEM
RM27L0U _51 Engine / Hybrid System _049309 CRUISE CONTROL _0235640 DYNAMIC LASER CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC LASER CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

The cruise control main switch operates 8 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP, CANCEL, and MODE. The SET, TAP-DOWN, and - (COAST) functions, and the RES (RESUME), TAP-UP, and + (ACCEL) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact point of the cruise control main switch is turned on with the switch operation. The ECM then reads the voltage value that has been changed by the switch operation to control MODE, SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL. The dynamic laser cruise control system has two cruise control modes: the constant speed control mode and vehicle-to-vehicle distance control mode.

·

The vehicle-to-vehicle distance control mode is always selected when starting up the dynamic laser cruise control system.

·

The operation of the constant speed control mode is the same as that for a conventional cruise control system.


WIRING DIAGRAM

E163052E02
6.344,5.326 6.673,5.474 0.329,0.148 10 ECM 5.751,0.663 6.029,0.800 0.278,0.138 10 A27 5.751,1.142 6.029,1.280 0.278,0.138 10 A27 5.799,0.455 5.982,0.597 0.184,0.142 10 45 5.802,0.941 5.979,1.083 0.177,0.142 10 37 3.217,0.656 3.495,0.814 0.278,0.158 10 H54 3.219,1.625 3.497,1.783 0.278,0.158 10 H54 3.226,1.148 3.504,1.307 0.278,0.158 10 H54 3.311,0.449 3.411,0.603 0.100,0.154 10 1 3.311,0.933 3.411,1.076 0.100,0.144 10 7 3.307,1.411 3.415,1.559 0.108,0.148 10 2 2.397,1.417 2.501,1.566 0.104,0.149 10 4 2.4,0.935 2.497,1.093 0.097,0.158 10 1 2.398,0.455 2.499,0.603 0.100,0.148 10 3 0.839,2.813 0.960,2.965 0.122,0.152 10 A 0.839,3.326 0.960,3.478 0.122,0.152 10 A 0.839,4.301 0.960,4.453 0.122,0.152 10 A 0.835,2.609 0.962,2.761 0.127,0.152 10 1 0.844,3.106 0.949,3.275 0.105,0.169 10 2 0.852,4.089 0.946,4.235 0.094,0.147 10 3 1.146,2.901 1.472,3.067 0.326,0.166 10 ECC 1.141,3.435 1.431,3.595 0.290,0.160 10 R/N 1.152,4.407 1.483,4.547 0.331,0.140 10 CCS 1.48,3.068 1.933,3.228 0.453,0.160 10 MODE 1.541,3.813 2.110,3.968 0.568,0.155 10 ON/OFF 2.643,3.813 3.045,3.963 0.403,0.149 10 +RES 3.652,3.816 4.022,3.976 0.370,0.160 10 -SET 4.367,3.819 4.969,3.985 0.601,0.166 10 CANCEL 2.314,4.825 4.059,4.963 1.745,0.138 10 Cruise Control Main Switch 2.481,2.012 3.294,2.184 0.813,0.172 10 Spiral Cable 2.32,0.65 2.563,0.795 0.243,0.145 10 z11 2.32,1.144 2.563,1.289 0.243,0.145 10 z11 2.32,1.617 2.563,1.762 0.243,0.145 10 z11 6.122,0.659 6.442,0.802 0.320,0.143 10 CCS 6.113,1.143 6.555,1.302 0.442,0.159 10 CCHG 2.738,0.58 3.059,0.723 0.320,0.143 10 CCS 2.727,1.526 3.052,1.691 0.326,0.166 10 ECC 2.756,1.048 3.046,1.208 0.290,0.160 10 R/N

PROCEDURE

1.READ VALUE USING TECHSTREAM
a.
E117754E06
1.27,0.226 2.298,0.551 1.029,0.325 10 + (ACCEL)/RES (RESUME) 2.843,1.037 3.285,1.185 0.443,0.149 10 MODE 2.576,2.202 3.145,2.356 0.569,0.154 10 ON-OFF 1.207,2.649 2.198,2.826 0.992,0.177 10 - (COAST)/SET 0.337,2.235 0.926,2.382 0.589,0.147 10 CANCEL

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Laser Cruise / Data List.


e.

Check the Data List for proper functioning of the cruise control main switch.

ECM (Laser Cruise)
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Main SW M-CPU Main switch signal (Main CPU) / ON or OFF ON: Main switch on
OFF: Main switch off
"3"
Cancel Switch CANCEL switch signal / ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch SET/COAST switch signal / ON or OFF ON: - (COAST)/SET switch on
OFF: - (COAST)/SET switch off
-
RES/ACC Switch RES/ACC switch signal / ON or OFF ON: + (ACCEL)/RES (RESUME) switch on
OFF: + (ACCEL)/RES (RESUME) switch off
-

OK:

When the cruise control main switch is operated, the display changes as shown above.


Result
Result Proceed to
OK A
NG (all items are defective) B
NG (1 to 3 items are defective) C



A

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT CRUISE CONTROL MAIN SWITCH

C

2.INSPECT CRUISE CONTROL MAIN SWITCH
a.

Remove the cruise control main switch (See page Engine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>REMOVAL).

E345248E01
2.073,2.854 2.354,3.052 0.281,0.198 3.521,0.146 4.531,0.51 1.01,0.365 10 false + (ACCEL)/ RES (RESUME) 5.448,0.313 6.063,0.51 0.615,0.198 10 false MODE 6.083,1.031 7,1.229 0.917,0.198 10 false ON-OFF 4.781,2.396 5.781,2.583 1,0.188 10 false - (COAST)/SET 3.99,2.052 4.906,2.25 0.917,0.198 10 false CANCEL 2.156,2.875 2.313,3.073 0.156,0.198 10 false A


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A-1 (ECC) - A-2 (R/N) Neutral 10 kΩ or higher
A-1 (ECC) - A-3 (CCS)
A-1 (ECC) - A-3 (CCS) + (ACCEL)/RES (RESUME) 235 to 245 Ω
A-1 (ECC) - A-3 (CCS) - (COAST)/SET 620 to 640 Ω
A-1 (ECC) - A-3 (CCS) CANCEL 1510 to 1570 Ω
A-1 (ECC) - A-3 (CCS) Main switch on Below 1 Ω
A-1 (ECC) - A-2 (R/N) Main switch on and MODE switch on Below 1 Ω




OK

3.INSPECT HARNESS AND CONNECTOR (CRUISE CONTROL MAIN SWITCH - SPIRAL CABLE)

NG

3.INSPECT HARNESS AND CONNECTOR (CRUISE CONTROL MAIN SWITCH - SPIRAL CABLE)
a.

Disconnect the z11 connector from the spiral cable.


U153917E02
0.198,1.427 0.469,1.594 0.271,0.167 10 false z11 0.229,3.698 0.354,3.865 0.125,0.167 10 false A 0.094,0.063 2.458,0.406 2.365,0.344 10 false Front view of wire harness connector: (to Spiral Cable) 0.094,2.302 2.448,2.646 2.354,0.344 10 false Front view of wire harness connector: (to Cruise Control Main Switch)

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 - z11-4 Always Below 1 Ω
A-2 - z11-1 Always Below 1 Ω
A-3 - z11-3 Always Below 1 Ω




OK

4.INSPECT SPIRAL CABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT SPIRAL CABLE
NOTICE:

The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the page shown in the brackets.


HINT:


a.

Remove the spiral cable.

E345235E03
2.74,0.135 3.063,0.344 0.323,0.208 3.979,2.344 4.302,2.552 0.323,0.208 2.969,0.865 3.125,1.104 3.125,1.104 3.229,1.104 false 2.844,0.865 2.646,1.115 2.646,1.115 2.542,1.115 false 4.042,3.146 3.885,2.906 3.885,2.906 3.802,2.906 false 4.146,3.125 4.573,2.49 4.573,2.49 4.677,2.49 false 2.958,0.708 3.177,0.417 3.177,0.417 3.302,0.417 false 4.052,3.021 3.854,2.552 3.854,2.552 3.771,2.552 false 0.052,0.052 1.26,0.615 1.208,0.563 10 false Component without harness connected: (Spiral Cable) 2.802,0.156 3.26,0.354 0.458,0.198 10 false z11 4.031,2.365 4.49,2.563 0.458,0.198 10 false H54 3.26,1.021 3.719,1.219 0.458,0.198 10 false CCS 2.24,1.031 2.698,1.229 0.458,0.198 10 false ECC 3.5,2.833 3.958,3.031 0.458,0.198 10 false CCS 4.698,2.417 5.156,2.615 0.458,0.198 10 false ECC 3.333,0.333 3.792,0.531 0.458,0.198 10 false R/N 3.521,2.479 3.979,2.677 0.458,0.198 10 false R/N


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Condition Spiral Cable Position Specified Condition
z11-1 (R/N) - H54-7 (R/N) Center Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
z11-3 (CCS) - H54-1 (CCS) Center Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
z11-4 (ECC) - H54-2 (ECC) Center Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right


HINT:

The spiral cable makes a maximum of approximately 5 rotations.



c.

Reinstall the spiral cable.



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM)
a.

Disconnect the A27 connector from the ECM.


b.

Disconnect the H54 connector from the spiral cable.


c.

Measure the resistance according to the value(s) in the table below.

E344854E03
3.25,1.458 3.583,1.688 0.333,0.229 0.771,1.573 1.104,1.802 0.333,0.229 1.49,1.688 1.125,2.042 false 1.625,1.646 2.406,1.375 false 5.313,1.917 5.135,2.479 false 1.531,1.802 1.792,2.25 false 5.344,1.792 5.833,2.438 false 0.552,0.083 2.792,0.469 2.24,0.385 10 false Front view of wire harness connector: (to Spiral Cable) 3.677,0.073 5.948,0.469 2.271,0.396 10 false Front view of wire harness connector: (to ECM) 0.823,1.604 1.281,1.802 0.458,0.198 10 false H54 3.302,1.49 3.76,1.688 0.458,0.198 10 false A27 0.948,2.063 1.406,2.26 0.458,0.198 10 false CCS 2.469,1.292 2.927,1.49 0.458,0.198 10 false ECC 4.99,2.479 5.448,2.677 0.458,0.198 10 false CCS 1.823,2.198 2.281,2.396 0.458,0.198 10 false R/N 5.729,2.458 6.344,2.656 0.615,0.198 10 false CCHG

Standard Resistance:
Tester Connection Condition Specified Condition
H54-1 (CCS) - A27-45 (CCS) Always Below 1 Ω
H54-7 (R/N) - A27-37 (CCHG) Always Below 1 Ω
H54-1 (CCS) - Body ground Always 10 kΩ or higher
H54-7 (R/N) - Body ground Always 10 kΩ or higher
H54-2 (ECC) - Body ground Always Below 1 Ω



d.

Reconnect the ECM and spiral cable connector.

Result
Result Proceed to
NG A
OK (for 3UR-FE) B
OK (for 3UR-FBE) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C