Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC LASER CRUISE CONTROL SYSTEM
RM27L0U _51 Engine / Hybrid System _049309 CRUISE CONTROL _0235640 DYNAMIC LASER CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC LASER CRUISE CONTROL SYSTEM  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  U1102  Lost Communication with Radar Sensor  


DESCRIPTION

The laser radar sensor and distance control ECU transmit the data for general vehicle control and diagnosis function along the communication line. The laser radar sensor transmits information about the vehicle in front to the distance control ECU.

DTC No. DTC Detection Condition Trouble Area
U0235 The ECM detects a communication error signal (from the laser radar sensor to the distance control ECU) for 0.15 seconds or more while the dynamic laser cruise control is in operation.
·

Communication circuit

·

Laser radar sensor

·

Distance control ECU


U1102 The ECM detects a communication error signal (from the distance control ECU to the laser radar sensor) for 0.15 seconds or more while the dynamic laser cruise control is in operation
·

Communication circuit

·

laser radar sensor

·

Distance control ECU



WIRING DIAGRAM

E163050E01
0.533,2.281 1.819,2.435 1.286,0.154 10 Laser Radar Sensor 5.321,2.235 6.772,2.397 1.451,0.162 10 Distance Control ECU 5.582,0.606 6.005,0.765 0.423,0.159 10 LRDD 5.582,1.153 5.849,1.297 0.267,0.144 10 IGB 5.582,1.713 6.011,1.882 0.429,0.169 10 SGND 1.186,0.618 1.593,0.762 0.407,0.144 10 LRDD 1.325,1.182 1.595,1.334 0.270,0.152 10 IGB 0.323,2.095 0.609,2.240 0.287,0.145 10 A26 5.144,2.043 5.425,2.205 0.280,0.161 10 A43 1.682,0.529 1.794,0.687 0.113,0.158 10 3 1.675,1.077 1.776,1.243 0.101,0.167 10 5 5.329,0.511 5.514,0.675 0.185,0.164 10 22 5.317,1.089 5.499,1.244 0.182,0.155 10 13 5.311,1.636 5.502,1.782 0.191,0.146 10 10

CAUTION / NOTICE / HINT

NOTICE:
·

When the distance control ECU is replaced with a new one, initialization must be performed (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC LASER CRUISE CONTROL SYSTEM>INITIALIZATION).

·

When the laser radar sensor is replaced with a new one, adjustment of the laser radar sensor beam axis must be performed (See page Engine / Hybrid System>CRUISE CONTROL>LASER SENSOR>ADJUSTMENT).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DISTANCE CONTROL ECU - LASER RADAR SENSOR)
a.

Disconnect the A43 distance control ECU connector and A26 laser radar sensor connector.

E345247E01
0.583,1.771 0.896,1.979 0.313,0.208 4,1.771 4.313,1.979 0.313,0.208 1.208,2.021 1.073,2.406 false 2.333,2.031 2.49,2.438 false 5.198,1.875 4.896,2.448 false 5.531,1.865 5.729,2.469 false 0.813,0.073 3.063,0.448 2.25,0.375 10 false Front view of wire harness connecter: (to Distance Control ECU) 4.042,0.073 6.281,0.438 2.24,0.365 10 false Front view of wire harness connecter: (to Laser Radar Sensor) 0.625,1.792 1.083,1.99 0.458,0.198 10 false A43 4.052,1.792 4.51,1.99 0.458,0.198 10 false A26 0.969,2.417 1.427,2.615 0.458,0.198 10 false IGB 2.354,2.438 2.969,2.635 0.615,0.198 10 false LRDD 4.688,2.458 5.302,2.656 0.615,0.198 10 false LRDD 5.646,2.469 6.104,2.667 0.458,0.198 10 false IGB


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-22 (LRDD) - A26-3 (LRDD) Always Below 1 Ω
A43-13 (IGB) - A26-5 (IGB) Always Below 1 Ω
A43-22 (LRDD) - Body ground Always 10 kΩ or higher
A43-13 (IGB) - Body ground Always 10 kΩ or higher



c.

Reconnect the distance control ECU connector and laser radar sensor connector.



OK

2.INSPECT DISTANCE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT DISTANCE CONTROL ECU
a.
U153948E01
1.62,1.38 1.889,1.542 0.269,0.163 10 A43 0.211,2.677 0.634,2.826 0.423,0.149 10 SGND 2.441,2.677 2.697,2.826 0.257,0.149 10 IGB 0.971,2.677 1.394,2.826 0.423,0.149 10 LRDD 2.209,2.137 2.441,2.677 false 1.624,2.128 1.439,2.677 false 1.573,2.055 0.713,2.677 false 0.207,0.102 2.505,0.503 2.298,0.401 10 Component with harness connected: (Distance Control ECU)

Disconnect the A43 distance control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A43-13 (IGB) - Body ground Ignition switch ON 11 to 14 V
A43-22 (LRDD) - A43-10 (SGND) Ignition switch ON 4.5 to 5.5 V



c.

Reconnect the distance control ECU connector.



OK

3.REPLACE LASER RADAR SENSOR

NG

3.REPLACE LASER RADAR SENSOR
a.

Temporarily replace the laser radar sensor with a new or normally functioning one (See page Engine / Hybrid System>CRUISE CONTROL>LASER SENSOR>REMOVAL).



NEXT

4.ADJUST LASER RADAR SENSOR
4.ADJUST LASER RADAR SENSOR
a.

HINT:

It is necessary to make the ECM recognize specification information (whether the vehicle is equipped with the dynamic laser cruise control system or not). When this procedure has not been carried out, this DTC may be output.



NEXT

5.CLEAR DTC
5.CLEAR DTC

NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Reproduce the DTC detection conditions under which the DTC is stored.

HINT:

If the DTC detection conditions are not correct, the system will not detect the trouble.



b.

Drive the vehicle at a speed of 45 km/h (28 mph) or more and turn the cruise control main switch ON. Push the -SET switch to activate the cruise control system.




OK

END (LASER RADAR SENSOR IS DEFECTIVE)

NG