Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE CARRIER
RM27L0U _52 Drivetrain _049314 AXLE AND DIFFERENTIAL _0235696 REAR AXLE CARRIER A

AXLE AND DIFFERENTIAL  REAR AXLE CARRIER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 42305 1.INSTALL REAR AXLE CARRIER SUB-ASSEMBLY LH

a.

Apply MP grease to a new O-ring.


b.
C180968

Install the new O-ring to the rear axle hub and bearing.

NOTICE:

Do not damage the O-ring.



c.
C180966

Install the axle hub and bearing to the rear axle carrier with the 4 bolts.

Torque:
86 N*m (877 kgf*cm, 64 ft.*lbf)


Hide 42402J 2.INSTALL REAR AXLE HUB DUST SEAL LH

a.
C180972E01
1.586,0.923 2.319,0.634 2.319,0.634 1.998,1.432 false 2.371,0.514 2.700,0.683 0.330,0.170 10 SST

Using SST and hammer, install the rear axle hub dust seal RH to the rear axle carrier.

SST
09223-15030  
09950-70010  (09951-07150)


Hide 3.INSTALL REAR AXLE ASSEMBLY

a.
C181149E03
0.76,2.656 1.604,2.875 1.604,2.875 2.458,2.51 false 0.208,0.333 0.333,0.521 0.125,0.188 10 true B 2.354,2.583 2.479,2.833 0.125,0.25 10 true A 1.167,2.875 1.948,3.052 0.781,0.177 10 false Matchmarks

Install the rear upper control arm with the bolt and nut.


b.

Align the matchmarks on the No. 1 rear suspension arm and adjust cam.


c.

Install the No. 1 rear suspension arm with the bolt and nut.

·

Bolt A


Torque:
250 N*m (2549 kgf*cm, 185 ft.*lbf)

·

Bolt B


Torque:
185 N*m (1886 kgf*cm, 137 ft.*lbf)


Hide 48740F 4.INSTALL NO. 2 REAR SUSPENSION ARM ASSEMBLY LH

a.
C180775

Install the No. 2 rear suspension arm to the rear axle with the nut.

Torque:
130 N*m (1326 kgf*cm, 96 ft.*lbf)


b.

Install a new cotter pin.


Hide 42312B 5.INSTALL REAR AXLE SHAFT NUT LH

a.
C180976

Using a 39 mm socket wrench, install the rear axle shaft nut LH .

Torque:
340 N*m (3467 kgf*cm, 251 ft.*lbf)


b.

Install the adjusting lock cap and new cotter pin.


Hide 42418C 6.INSTALL REAR HUB GREASE CAP LH

a.

Install the rear hub grease cap LH.

NOTICE:

Mark sure to securely fit the bearing to the axle hub.



Hide 89546 7.INSTALL REAR SPEED SENSOR LH

a.
C178153

Using a hexagon wrench, install the rear speed sensor with the bolt.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)

NOTICE:
·

Make sure that there are no pieces of iron or other foreign matter attached to the sensor tip part.

·

While inserting the speed sensor into the knuckle hole, do not strike or damage the sensor tip part.

·

After installing the speed sensor, make sure that there is no clearance or foreign matter between the sensor stay part and the knuckle.

·

Make sure that there is no foreign matter attached to the magnetic rotor.




b.

Connect the rear speed sensor connector.


Hide 8.INSTALL PARKING BRAKE ASSEMBLY

Hide 48090B 9.INSTALL REAR PNEUMATIC CYLINDER ASSEMBLY LH (for Pneumatic Cylinder Type)

Hide 48231B 10.INSTALL REAR COIL SPRING LH (for Coil Spring Type)

Hide 11.INSPECT REAR WHEEL ALIGNMENT (for Pneumatic Cylinder Type)