Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM
RM27L0U _53 Suspension _049315 SUSPENSION CONTROL _0235712 AIR SUSPENSION SYSTEM D

SUSPENSION CONTROL  AIR SUSPENSION SYSTEM  TEST MODE PROCEDURE  


TEST MODE PROCEDURE (SIGNAL CHECK)


HINT:
·

When entering the test mode, the suspension control ECU sets all the test mode DTCs first. After completing the test mode for each check item, the test mode DTCs that are determined to be normal by the suspension control ECU will be cleared. The test mode DTCs for other check items may not be cleared when only a certain signal is inspected.

·

When the test mode returns back to the normal mode, all the test mode DTCs will be cleared.



a.

Turn the ignition switch off.


b.

Check that the shift lever is in P.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON and the Techstream on.


e.

Enter the following menus: Chassis / Air suspension / Utility / Signal Check.


f.

The engine is started without stepping on the brake pedal.


g.
C353460E01
0.021,0.031 2.156,0.333 2.135,0.302 10 false Blinking Pattern in TEST MODE: 0.323,0.469 1.427,0.667 1.104,0.198 10 false 0.125 Seconds 0.26,0.875 0.573,1.073 0.313,0.198 10 false ON 1.927,0.469 3.031,0.667 1.104,0.198 10 false 0.125 Seconds 0.26,1.688 0.719,1.885 0.458,0.198 10 false OFF

Check that the height control MAN. indicator light comes on for several seconds and then blinks in Test Mode.


h.

Set each of the check items to the condition shown under Operation in the test mode table below.

Test Mode (Input Signal Check) Table
Check Item Operation
Absorber control switch signal Slowly move the absorber control switch "COMFORT" to "SPORT" and "COMFORT"
Height control switch signal Press the height control switch "UP" first and then press "DOWN"
Height control mode select switch signal ON to OFF (Height control mode select switch pushed)


i.

Read the test mode DTCs by following the prompts on the Techstream screen.


j.

Check the malfunction using the code table below. After completing the test mode, disconnect the Techstream and turn the ignition switch off.



TEST MODE DTC CHART


HINT:

When entering test mode, the suspension control ECU stores all the test mode DTCs. If the deletion conditions for a test mode DTC are met, it is cleared.


a.

If a trouble code is displayed during the test mode DTC check, check the circuit listed for that code. For details of each code, refer to "See page" for the respective "DTC Code" in the chart.

DTC Code Diagnosis Trouble Area See page
C1791 Absorber Control Switch Circuit
·

Absorber control switch (Suspension control switch)

·

Absorber control switch circuit

·

Suspension control ECU


(Click here)
C1792 Height control switch circuit
·

Height control switch (No. 1 absorber control switch)

·

Height control switch circuit

·

Suspension control ECU


(Click here)
C1793 Height control off switch circuit
·

Height control mode select switch (No. 2 absorber control switch)

·

Height control mode select switch circuit

·

Suspension control ECU


(Click here)
C1796 Front Acceleration Sensor RH Malfunction
·

Front acceleration sensor RH

·

Front acceleration sensor RH circuit

·

Suspension control ECU


(Click here)
C1797 Front Acceleration Sensor LH Malfunction
·

Front acceleration sensor LH

·

Front acceleration sensor LH circuit

·

Suspension control ECU


(Click here)
C1798 Rear Acceleration Sensor Malfunction
·

Suspension control ECU


(Click here)