Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM27L0U _54 Brake _049321 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0235735 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1241/41  Low Battery Positive Voltage or Abnormally High Battery Positive Voltage  


DESCRIPTION

When there is an abnormality in the power supply circuit of the VSC actuator (skid control ECU), the skid control ECU sets a DTC and the operation is prohibited by the fail-safe function. This DTC is set when the voltage supplied to terminal +BS is outside the DTC detection threshold due to abnormalities of the battery, power source circuits or charging circuits such as the alternator circuit.

The fail-safe function is canceled when the voltage to terminal +BS returns to normal.

HINT:

If the vehicle speed is 20 km/h (12 mph) or less when the battery voltage is low, the ABS warning light and slip indicator light illuminate. However, a DTC will not be output.


DTC Code DTC Detection Condition Trouble Area
C1241/41 When any of following conditions detected:
1.

+BS terminal voltage 18 V or more (momentary occurrence included).

2.

At vehicle speed 20 km/h (12 mph) or more, +BS terminal voltage 9.7 V or less for 0.21 seconds or more.

3.

At vehicle speed 20 km/h (12 mph) or more, +BS terminal voltage 8.5 V or less (momentary occurrence included).


·

ABS2 H-fuse

·

Battery

·

Charging system

·

Power source circuit

·

VSC actuator (skid control ECU)



CAUTION / NOTICE / HINT

NOTICE:

When replacing the VSC actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result
Result Proceed to
OK A
NG (for 3UR-FE) B
NG (for 3UR-FBE) C



A

2.INSPECT FUSE (ABS2)

B

C

2.INSPECT FUSE (ABS2)
a.
C152723E03
0.065,0.235 1.758,0.419 1.693,0.184 10 Engine Room Relay Block: 1.088,2.91 2.126,3.076 1.038,0.165 10 ABS2 H-fuse 1.798,2.147 1.463,2.827 false

Remove the ABS2 H-fuse from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ABS2 H-fuse Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)

NG

CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)
a.
U153709E01
0.097,0.049 2.454,0.362 2.357,0.313 10 Front view of wire harness connector: (to Skid Control ECU) 2.862,2.712 3.164,2.861 0.302,0.149 10 +BS 0.145,1.485 0.568,1.641 0.423,0.156 10 GND1 3.047,2.439 3.047,2.701 false 0.191,1.143 0.514,1.317 0.323,0.174 10 A19 0.385,1.693 0.385,1.938 false

Disconnect the A19 ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A19-32 (+BS) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A19-16 (GND1) - Body ground Always Below 1 Ω




OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.RECONFIRM DTC

b.

Start the engine.


c.

Check if the same DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B



A

B