Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM27L0U _54 Brake _049321 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0235735 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C0200/31  Right Front Wheel Speed Sensor Signal  C0205/32  Left Front Wheel Speed Sensor Signal  C1271/71  Low Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1272/72  Low Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1275/75  Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1276/76  Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1330/35  Open Circuit in Right Front Wheel Speed Sensor Circuit  C1331/36  Open Circuit in Left Front Wheel Speed Sensor Circuit  


DESCRIPTION

The speed sensors detect the wheel speeds and send appropriate signals to the skid control ECU.

Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change as the rotors turn.

The speed sensors detect those magnetic changes and send pulse signals to the skid control ECU. The ECU monitors the wheel speeds through these pulse signals to control the ABS control system.

C152717E06
1.927,0.979 2.25,0.802 2.25,0.802 2.365,0.802 false 2.417,1.76 2.594,1.76 false 0.073,0.104 1.448,0.323 1.375,0.219 10 false Front Speed Sensor: 2.406,0.729 3.313,0.927 0.906,0.198 10 false Speed Sensor 2.625,1.688 3.51,1.885 0.885,0.198 10 false Speed Rotor 4.177,2.219 4.948,2.438 0.771,0.219 10 false Low Speed 5.125,2.25 5.927,2.427 0.802,0.177 10 false High Speed 6.25,1.792 6.635,1.99 0.385,0.198 10 false 0.7 V 6.25,1.417 6.698,1.615 0.448,0.198 10 false 1.4 V 3.49,0.49 4.948,0.667 1.458,0.177 10 false Waveform (Reference): 3.49,0.729 6.271,0.906 2.781,0.177 10 false Between Speed Sensor (-) and Body Ground

HINT:

When testing voltage, perform the test while the connector between the sensor and ECU is connected. Do not disconnect the connector between the sensor and ECU.


DTC Code DTC Detection Condition Trouble Area
C0200/31
C0205/32
When any of following conditions detected:
1.

When vehicle speed 15 km/h (9 mph), wheel speed 6 km/h (4 mph) or less.

2.

At vehicle speed of 45 km/h (28 mph) or more, open in sensor harness occurs intermittently for 0.2 seconds or more.

3.

When vehicle speed between 10 km/h (6 mph) and 15 km/h (9 mph) for 3 minutes, one wheel speed 0 km/h (0 mph).

4.

Pressure reduction mode of ABS system lasts for 28 seconds or more.

5.

When vehicle driven at speed of 20 km/h (12 mph) or more, difference between wheel speeds indicated by two sensors twice or more for 30 seconds or more.

6.

Foreign matter adheres to sensor rotor.


·

Front speed sensor

·

Front speed sensor circuit

·

Sensor installation

·

Foreign matter on sensor rotor


C1271/71
C1272/72
Detected only during test mode.
·

Front speed sensor

·

Front speed sensor circuit

·

Sensor installation

·

Foreign matter on sensor rotor


C1275/75
C1276/76
Detected only during test mode.
·

Front speed sensor (open)

·

Front speed sensor circuit (open)


C1330/35
C1331/36
Open in front speed sensor circuit continues for 0.15 seconds or more.
·

Front speed sensor (open)

·

Front speed sensor circuit (open)



HINT:
·

DTCs C0200/31 and C1330/35 are for the front speed sensor RH.

·

DTCs C0205/32 and C1331/36 are for the front speed sensor LH.



WIRING DIAGRAM

C241007E11
0.386,1.004 1.170,1.314 0.784,0.310 10 Front Speed Sensor RH 0.386,2.265 1.173,2.580 0.787,0.315 10 Front Speed Sensor LH 5.27,3.048 6.485,3.236 1.215,0.189 10 Skid Control ECU 5.534,0.744 5.851,0.887 0.317,0.143 10 FR+ 5.533,1.236 5.856,1.376 0.323,0.140 10 FR- 5.54,2.442 5.793,2.584 0.253,0.142 10 FL- 5.539,1.955 5.823,2.101 0.284,0.145 10 FL+ 2.294,2.337 2.392,2.484 0.098,0.147 10 1 2.294,0.646 2.392,0.796 0.098,0.150 10 2 2.298,1.108 2.392,1.256 0.095,0.148 10 1 2.294,1.841 2.392,1.991 0.098,0.150 10 2 0.386,0.825 0.724,0.982 0.339,0.157 10 z3 0.386,2.081 0.704,2.239 0.319,0.157 10 z4 5.298,0.639 5.471,0.788 0.173,0.149 10 34 5.298,1.129 5.473,1.278 0.175,0.149 10 33 5.298,2.352 5.482,2.493 0.184,0.142 10 46 5.298,1.871 5.482,2.017 0.184,0.145 10 45 5.27,2.881 5.647,3.063 0.378,0.181 10 A19

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the VSC actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Check the speed sensor signal in test mode after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).



PROCEDURE

1.READ VALUE USING TECHSTREAM (FRONT SPEED SENSOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List mode on the Techstream.

ABS/VSC/TRAC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading /
min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed Similar speed as indicated on speedometer
FL Wheel Speed Front wheel speed sensor LH reading /
min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed Similar speed as indicated on speedometer


d.

Check that the speed value output from the speed sensor displayed on the Techstream and the speed value displayed on the speedometer are almost the same when driving the vehicle.

OK:

The speed value output from the speed sensor displayed on the Techstream is the same as the actual vehicle speed.


HINT:

There is a tolerance of +/-10% in the speedometer indication.




OK

2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

NG

4.CHECK FRONT SPEED SENSOR INSTALLATION
2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Perform a TEST MODE inspection and check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).

OK:

No DTC output.




OK

3.RECONFIRM DTC

NG

4.CHECK FRONT SPEED SENSOR INSTALLATION
3.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.


d.

Check if the same DTC(s) is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

B

10.REPLACE FRONT SPEED SENSOR
4.CHECK FRONT SPEED SENSOR INSTALLATION
I044006E26
0.667,1.406 0.875,1.604 false 0.938,1.594 1.781,1.875 0.844,0.281 10 false No clearance 0.417,1.74 0.646,1.906 0.229,0.167 10 false OK 2.563,1.844 2.792,2.01 0.229,0.167 10 false NG

a.

Check that the speed sensor installation bolt is tightened properly (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>INSTALLATION).

OK:

The installation bolt is tightened properly.




OK

5.CHECK FRONT SPEED SENSOR

NG

5.CHECK FRONT SPEED SENSOR
a.

Visually check the speed sensor for deformation and damage.

OK:

No deformation or damage.

There is no gap between the sensor and front steering knuckle.




OK

6.CHECK SPEED SENSOR TIP

NG

6.CHECK SPEED SENSOR TIP

b.

Check the sensor tip.

OK:

No scratches or foreign matter on the sensor tip.




OK

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)

NG

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
a.
C353356E01
0.083,0.885 0.458,1.094 0.375,0.208 0.083,3.375 0.458,3.583 0.375,0.208 1.74,3.375 2.115,3.583 0.375,0.208 0.448,2.177 0.698,1.823 true 1.073,2.156 0.885,1.823 true 2.302,2.188 2.552,1.833 true 2.927,2.177 2.74,1.844 true 0.063,0.052 2.354,0.417 2.292,0.365 10 false Front view of wire harness connector: (to Skid Control ECU) 0.156,0.917 0.552,1.104 0.396,0.188 10 false A19 0.271,2.198 0.563,2.396 0.292,0.198 10 false FL- 0.938,2.198 1.271,2.396 0.333,0.198 10 false FL+ 2.104,2.208 2.427,2.406 0.323,0.198 10 false FR+ 2.854,2.208 3.177,2.406 0.323,0.198 10 false FR- 0.052,2.51 2.344,2.875 2.292,0.365 10 false Front view of wire harness connector: (to Front Speed Sensor) 0.208,3.385 0.604,3.573 0.396,0.188 10 false z3 1.865,3.396 2.26,3.583 0.396,0.188 10 false z4

Confirm that the skid control ECU connector and speed sensor connector are properly connected.


b.

Disconnect the A19 ECU connector.


c.

Disconnect the z3 and z4 sensor connectors.


d.

Inspect both the connector case and the terminal for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A19-34 (FR+) - z3-2 Always Below 1 Ω
A19-33 (FR-) - z3-1
A19-34 (FR+) - Body ground Always 10 kΩ or higher
A19-33 (FR-) - Body ground

for LH
Tester Connection Condition Specified Condition
A19-45 (FL+) - z4-2 Always Below 1 Ω
A19-46 (FL-) - z4-1
A19-45 (FL+) - Body ground Always 10 kΩ or higher
A19-46 (FL-) - Body ground




OK

8.INSPECT FRONT SPEED SENSOR (INPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT FRONT SPEED SENSOR (INPUT VOLTAGE)
a.
U153437E02
0.104,0.083 2.521,0.521 2.417,0.438 10 false Front view of wire harness connector: (to Front Speed Sensor) 0.229,1.719 0.396,1.865 0.167,0.146 10 false z3 1.854,1.719 2.042,1.865 0.188,0.146 10 false z4

Reconnect the A19 ECU connector.


b.

Disconnect the z3 and z4 sensor connectors.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z3-2 - Body ground Ignition switch ON 7.5 to 20 V
z4-2 - Body ground




OK

9.RECONFIRM DTC

NG

9.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.


d.

Check if the same DTC(s) is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B



A

10.REPLACE FRONT SPEED SENSOR

B

10.REPLACE FRONT SPEED SENSOR
a.


NEXT

11.RECONFIRM DTC
11.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.


d.

Check if the same DTC(s) is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B



A

B

END