Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049331 PARK ASSIST / MONITORING _0235792 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB0  Short to +B in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects a +B short in the blind spot monitor indicator RH.

DTC Code DTC Detection Condition Trouble Area
C1AB0 With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the voltage applied to the indicator is high for a certain amount of time even though the blind spot monitor sensor is not outputting voltage to the indicator.
·

Harness or connector

·

Blind spot monitor sensor RH

·

Outer rear view mirror assembly RH

·

Outer rear view mirror glass RH



WIRING DIAGRAM

E221720E03
2.544,1.272 2.681,1.424 0.137,0.151 10 7 3.506,1.272 3.643,1.424 0.137,0.151 10 9 5.397,1.258 5.525,1.410 0.128,0.151 10 6 3.062,1.272 3.468,1.424 0.406,0.151 10 BSR+ 5.57,1.356 5.976,1.508 0.406,0.151 10 OMIR 3.142,1.735 3.426,1.886 0.284,0.151 10 LP- 0.989,2.155 1.367,2.306 0.378,0.151 10 I6 0.755,3.365 1.198,3.516 0.443,0.151 10 L6 5.405,3.391 5.848,3.542 0.443,0.151 10 P25 2.357,1.366 2.494,1.517 0.137,0.151 10 + 2.357,1.84 2.494,1.991 0.137,0.151 10 - 2.553,1.737 2.691,1.888 0.137,0.151 10 5 3.506,1.737 3.643,1.888 0.137,0.151 10 5 0.989,2.328 3.108,2.697 2.119,0.369 10 Outer Rear View Mirror Glass RH (Blind Spot Monitor Indicator RH) 0.755,3.547 3.133,3.721 2.378,0.174 10 Outer Rear View Mirror Assembly RH 5.405,3.573 6.602,3.888 1.198,0.316 10 Blind Spot Monitor Sensor RH

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch assembly (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.




OK

NG

2.CHECK HARNESS AND CONNECTOR
2.CHECK HARNESS AND CONNECTOR
a.

Disconnect the P25 blind spot monitor sensor RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
P25-6 (OMIR) - Body ground Ignition switch ON Below 1 V




OK

NG

3.CHECK HARNESS AND CONNECTOR
3.CHECK HARNESS AND CONNECTOR
a.

Disconnect the L6 outer rear view mirror assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
P25-6 (OMIR) - Body ground Ignition switch ON Below 1 V




OK

4.CHECK HARNESS AND CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR
a.

Disconnect the l6 outer rear view mirror glass RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
P25-6 (OMIR) - Body ground Ignition switch ON Below 1 V




OK

REPLACE OUTER REAR VIEW MIRROR GLASS RH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH