Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049331 PARK ASSIST / MONITORING _0235792 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB1  Short to +B in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects a +B short in the blind spot monitor indicator LH.

DTC Code DTC Detection Condition Trouble Area
C1AB1 With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the voltage applied to the indicator is high for a certain amount of time even though the blind spot monitor sensor is not outputting voltage to the indicator.
·

Harness or connector

·

Blind spot monitor sensor LH

·

Outer rear view mirror assembly LH

·

Outer rear view mirror glass LH



WIRING DIAGRAM

E221720E44
2.531,1.26 2.667,1.406 0.135,0.146 10 false 7 3.51,1.26 3.646,1.406 0.135,0.146 10 false 9 5.385,1.26 5.51,1.406 0.125,0.146 10 false 6 3.063,1.26 3.469,1.406 0.406,0.146 10 false BSL+ 5.563,1.333 5.969,1.479 0.406,0.146 10 false OMIL 3.167,1.729 3.438,1.875 0.271,0.146 10 false LP- 0.938,2.146 1.313,2.292 0.375,0.146 10 false m5 0.76,3.375 1.208,3.521 0.448,0.146 10 false M5 5.49,3.375 5.938,3.521 0.448,0.146 10 false O46 2.375,1.344 2.51,1.49 0.135,0.146 10 false + 2.385,1.792 2.521,1.938 0.135,0.146 10 false - 2.542,1.729 2.677,1.875 0.135,0.146 10 false 5 3.51,1.729 3.646,1.875 0.135,0.146 10 false 5 0.938,2.313 3.063,2.698 2.125,0.385 10 false Outer Rear View Mirror Glass LH (Blind Spot Monitor Indicator LH) 0.76,3.542 3.094,3.708 2.333,0.167 10 false Outer Rear View Mirror Assembly LH 5.49,3.542 6.646,3.885 1.156,0.344 10 false Blind Spot Monitor Sensor LH

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch assembly (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.




OK

NG

2.CHECK HARNESS AND CONNECTOR
2.CHECK HARNESS AND CONNECTOR
a.

Disconnect the O46 blind spot monitor sensor LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O46-6 (OMIL) - Body ground Ignition switch ON Below 1 V




OK

NG

3.CHECK HARNESS AND CONNECTOR
3.CHECK HARNESS AND CONNECTOR
a.

Disconnect the M5 outer rear view mirror assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O46-6 (OMIL) - Body ground Ignition switch ON Below 1 V




OK

4.CHECK HARNESS AND CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR
a.

Disconnect the m5 outer rear view mirror glass LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O46-6 (OMIL) - Body ground Ignition switch ON Below 1 V




OK

REPLACE OUTER REAR VIEW MIRROR GLASS LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH