Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049331 PARK ASSIST / MONITORING _0235792 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB2  Short to GND in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects a ground short in the blind spot monitor indicator RH.

DTC Code DTC Detection Condition Trouble Area
C1AB2 With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the voltage output from the blind spot monitor sensor to the indicator is low for a certain amount of time.
·

Harness or connector

·

Outer rear view mirror assembly RH

·

Outer rear view mirror glass RH

·

Blind spot monitor sensor RH



WIRING DIAGRAM

E221720E03
2.544,1.272 2.681,1.424 0.137,0.151 10 7 3.506,1.272 3.643,1.424 0.137,0.151 10 9 5.397,1.258 5.525,1.410 0.128,0.151 10 6 3.062,1.272 3.468,1.424 0.406,0.151 10 BSR+ 5.57,1.356 5.976,1.508 0.406,0.151 10 OMIR 3.142,1.735 3.426,1.886 0.284,0.151 10 LP- 0.989,2.155 1.367,2.306 0.378,0.151 10 I6 0.755,3.365 1.198,3.516 0.443,0.151 10 L6 5.405,3.391 5.848,3.542 0.443,0.151 10 P25 2.357,1.366 2.494,1.517 0.137,0.151 10 + 2.357,1.84 2.494,1.991 0.137,0.151 10 - 2.553,1.737 2.691,1.888 0.137,0.151 10 5 3.506,1.737 3.643,1.888 0.137,0.151 10 5 0.989,2.328 3.108,2.697 2.119,0.369 10 Outer Rear View Mirror Glass RH (Blind Spot Monitor Indicator RH) 0.755,3.547 3.133,3.721 2.378,0.174 10 Outer Rear View Mirror Assembly RH 5.405,3.573 6.602,3.888 1.198,0.316 10 Blind Spot Monitor Sensor RH

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch assembly (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.




OK

NG

2.CHECK HARNESS AND CONNECTOR
2.CHECK HARNESS AND CONNECTOR
a.

Disconnect the P25 blind spot monitor sensor RH connector.


b.

Disconnect the L6 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L6-9 (BSR+) - Body ground Always 10 kΩ or higher




OK

3.INSPECT OUTER REAR VIEW MIRROR GLASS RH (BLIND SPOT MONITOR INDICATOR RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER REAR VIEW MIRROR GLASS RH (BLIND SPOT MONITOR INDICATOR RH)
a.
B286082E03
2.563,3.01 2.781,3.208 2.781,3.208 3.031,3.208 true 2.563,2.698 2.948,2.292 2.948,2.292 3.031,2.292 true 3.094,3.125 3.229,3.271 0.135,0.146 10 false + 3.094,2.198 3.229,2.344 0.135,0.146 10 false -

Remove the outer rear view mirror glass RH (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>REMOVAL).


b.

Check the outer rear view mirror indicator.

i.

Apply battery voltage to the outer rear view mirror glass RH (outer rear view mirror indicator RH) and check that the outer rear view mirror indicator turns on.

OK:
Connection Specified Condition
Battery positive (+) → Terminal 7 (+)
Battery negative (-) → Terminal 5 (-)
Indicator turns on





OK

4.CHECK HARNESS AND CONNECTOR

NG

REPLACE OUTER REAR VIEW MIRROR GLASS RH

4.CHECK HARNESS AND CONNECTOR
a.

Disconnect the l6 outer rear view mirror glass RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P25-6 (OMIR) - Body ground Always 10 kΩ or higher




OK

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH