Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049331 PARK ASSIST / MONITORING _0235792 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB3  Short to GND in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects a ground short in the blind spot monitor indicator LH.

DTC Code DTC Detection Condition Trouble Area
C1AB3 With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the voltage output from the blind spot monitor sensor to the indicator is low for a certain amount of time.
·

Outer rear view mirror assembly LH

·

Harness or connector

·

Blind spot monitor sensor LH



WIRING DIAGRAM

E221720E44
2.531,1.26 2.667,1.406 0.135,0.146 10 false 7 3.51,1.26 3.646,1.406 0.135,0.146 10 false 9 5.385,1.26 5.51,1.406 0.125,0.146 10 false 6 3.063,1.26 3.469,1.406 0.406,0.146 10 false BSL+ 5.563,1.333 5.969,1.479 0.406,0.146 10 false OMIL 3.167,1.729 3.438,1.875 0.271,0.146 10 false LP- 0.938,2.146 1.313,2.292 0.375,0.146 10 false m5 0.76,3.375 1.208,3.521 0.448,0.146 10 false M5 5.49,3.375 5.938,3.521 0.448,0.146 10 false O46 2.375,1.344 2.51,1.49 0.135,0.146 10 false + 2.385,1.792 2.521,1.938 0.135,0.146 10 false - 2.542,1.729 2.677,1.875 0.135,0.146 10 false 5 3.51,1.729 3.646,1.875 0.135,0.146 10 false 5 0.938,2.313 3.063,2.698 2.125,0.385 10 false Outer Rear View Mirror Glass LH (Blind Spot Monitor Indicator LH) 0.76,3.542 3.094,3.708 2.333,0.167 10 false Outer Rear View Mirror Assembly LH 5.49,3.542 6.646,3.885 1.156,0.344 10 false Blind Spot Monitor Sensor LH

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch assembly (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.




OK

NG

2.CHECK HARNESS AND CONNECTOR
2.CHECK HARNESS AND CONNECTOR
a.

Disconnect the O46 blind spot monitor sensor LH connector.


b.

Disconnect the M5 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M5-9 (BSL+) - Body ground Always 10 kΩ or higher




OK

3.INSPECT OUTER REAR VIEW MIRROR GLASS LH (OUTER REAR VIEW MIRROR INDICATOR LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER REAR VIEW MIRROR GLASS LH (OUTER REAR VIEW MIRROR INDICATOR LH)
a.
B284119E04
2.573,2.979 2.813,3.208 2.813,3.208 3.063,3.208 true 2.573,2.698 2.948,2.281 2.948,2.281 3.052,2.281 true 3.125,3.115 3.313,3.302 0.188,0.188 10 false + 3.104,2.188 3.292,2.375 0.188,0.188 10 false -

Remove the outer rear view mirror glass LH (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>REMOVAL).


b.

Check the outer rear view mirror indicator.

i.

Apply battery voltage to the outer rear view mirror glass LH (outer rear view mirror indicator LH) and check that the outer rear view mirror indicator turns on.

OK:
Connection Specified Condition
Battery positive (+) → Terminal 7 (+)
Battery negative (-) → Terminal 5 (-)
Indicator turns on





OK

4.CHECK HARNESS AND CONNECTOR

NG

REPLACE OUTER REAR VIEW MIRROR GLASS LH

4.CHECK HARNESS AND CONNECTOR
a.

Disconnect the m5 outer rear view mirror glass LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O46-6 (OMIL) - Body ground Always 10 kΩ or higher




OK

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH