Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049331 PARK ASSIST / MONITORING _0235792 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB4  Open in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects an open in the blind spot monitor indicator RH.

DTC Code DTC Detection Condition Trouble Area
C1AB4 With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the current flowing to the indicator is below a specified value when indicator operation voltage is sent to the indicator.
·

Blind spot monitor indicator RH

·

Outer rear view mirror assembly RH

·

Harness or connector

·

Blind spot monitor sensor RH



WIRING DIAGRAM

E221720E03
2.544,1.272 2.681,1.424 0.137,0.151 10 7 3.506,1.272 3.643,1.424 0.137,0.151 10 9 5.397,1.258 5.525,1.410 0.128,0.151 10 6 3.062,1.272 3.468,1.424 0.406,0.151 10 BSR+ 5.57,1.356 5.976,1.508 0.406,0.151 10 OMIR 3.142,1.735 3.426,1.886 0.284,0.151 10 LP- 0.989,2.155 1.367,2.306 0.378,0.151 10 I6 0.755,3.365 1.198,3.516 0.443,0.151 10 L6 5.405,3.391 5.848,3.542 0.443,0.151 10 P25 2.357,1.366 2.494,1.517 0.137,0.151 10 + 2.357,1.84 2.494,1.991 0.137,0.151 10 - 2.553,1.737 2.691,1.888 0.137,0.151 10 5 3.506,1.737 3.643,1.888 0.137,0.151 10 5 0.989,2.328 3.108,2.697 2.119,0.369 10 Outer Rear View Mirror Glass RH (Blind Spot Monitor Indicator RH) 0.755,3.547 3.133,3.721 2.378,0.174 10 Outer Rear View Mirror Assembly RH 5.405,3.573 6.602,3.888 1.198,0.316 10 Blind Spot Monitor Sensor RH

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch assembly (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.




OK

NG

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - BLIND SPOT MONITOR SENSOR RH AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - BLIND SPOT MONITOR SENSOR RH AND BODY GROUND)
a.

Disconnect the P25 blind spot monitor sensor RH connector.


b.

Disconnect the L6 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P25-6 (OMIR) - L6-9 (BSR+) Always Below 1 Ω
L6-5 (LP-) - Body ground Always Below 1 Ω




OK

3.INSPECT BLIND SPOT MONITOR INDICATOR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT BLIND SPOT MONITOR INDICATOR RH
a.
E231441E02
1.021,1.167 0.938,0.677 0.938,0.677 0.729,0.677 true 1.729,1.167 2.25,0.656 2.25,0.656 2.604,0.656 true 0.146,2.542 0.396,2.74 0.25,0.198 10 false *1 2.677,0.573 3.042,0.74 0.365,0.167 10 false LP- 0.313,0.594 0.771,0.76 0.458,0.167 10 false BSR+

Remove the outer rear view mirror assembly RH (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL).


b.

Apply battery voltage to the terminal of the outer rear view mirror assembly RH, and check that the blind spot monitor indicator turns on.

Standard:
Connection Specified Condition
Battery positive (+) → 9 (BSR+)
Battery negative (-) → 5 (LP-)
Indicator turns on


Text in Illustration
*1 Blind Spot Monitor Indicator RH



OK

NG

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
a.
E231117E03
1.031,0.906 1.135,0.438 1.135,0.438 1.198,0.438 true 1.719,0.906 1.823,0.438 1.823,0.438 1.896,0.438 true 1.719,3.021 1.26,3.188 1.26,3.188 1.188,3.188 true 1.719,2.698 2.167,2.177 2.167,2.177 2.229,2.177 true 0.083,0.063 0.271,0.208 0.188,0.146 10 false *a 1.229,0.354 1.635,0.5 0.406,0.146 10 false BSR+ 0.094,1.771 0.281,1.917 0.188,0.146 10 false *b 1.938,0.365 2.344,0.51 0.406,0.146 10 false LP- 1.042,3.094 1.167,3.24 0.125,0.146 10 false + 2.292,2.083 2.417,2.229 0.125,0.146 10 false -

Remove the outer rear view mirror assembly RH (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL).


b.

Remove the outer rear view mirror glass RH (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>REMOVAL).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (BSR+) - 7 (+) Always Below 1 Ω
5 (LP-) - 5 (-) Always Below 1 Ω


Text in Illustration
*a Vehicle Side
*b Outer Rear View Mirror Glass RH Side



OK

REPLACE OUTER REAR VIEW MIRROR GLASS RH (BLIND SPOT MONITOR INDICATOR RH)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH