Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049331 PARK ASSIST / MONITORING _0235792 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB5  Open in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects an open in the blind spot monitor indicator LH.

DTC Code DTC Detection Condition Trouble Area
C1AB5 With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the current flowing to the indicator is below a specified value when indicator operation voltage is sent to the indicator.
·

Blind spot monitor indicator LH

·

Outer rear view mirror assembly LH

·

Harness or connector

·

Blind spot monitor sensor LH



WIRING DIAGRAM

E221720E44
2.531,1.26 2.667,1.406 0.135,0.146 10 false 7 3.51,1.26 3.646,1.406 0.135,0.146 10 false 9 5.385,1.26 5.51,1.406 0.125,0.146 10 false 6 3.063,1.26 3.469,1.406 0.406,0.146 10 false BSL+ 5.563,1.333 5.969,1.479 0.406,0.146 10 false OMIL 3.167,1.729 3.438,1.875 0.271,0.146 10 false LP- 0.938,2.146 1.313,2.292 0.375,0.146 10 false m5 0.76,3.375 1.208,3.521 0.448,0.146 10 false M5 5.49,3.375 5.938,3.521 0.448,0.146 10 false O46 2.375,1.344 2.51,1.49 0.135,0.146 10 false + 2.385,1.792 2.521,1.938 0.135,0.146 10 false - 2.542,1.729 2.677,1.875 0.135,0.146 10 false 5 3.51,1.729 3.646,1.875 0.135,0.146 10 false 5 0.938,2.313 3.063,2.698 2.125,0.385 10 false Outer Rear View Mirror Glass LH (Blind Spot Monitor Indicator LH) 0.76,3.542 3.094,3.708 2.333,0.167 10 false Outer Rear View Mirror Assembly LH 5.49,3.542 6.646,3.885 1.156,0.344 10 false Blind Spot Monitor Sensor LH

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch assembly (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.




OK

NG

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH AND BODY GROUND)
a.

Disconnect the O46 blind spot monitor sensor LH connector.


b.

Disconnect the M5 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O46-6 (OMIL) - M5-9 (BSL+) Always Below 1 Ω
M5-5 (LP-) - Body ground Always Below 1 Ω




OK

3.INSPECT BLIND SPOT MONITOR INDICATOR LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT BLIND SPOT MONITOR INDICATOR LH
a.
E231442E02
1.094,1.25 0.865,0.708 0.865,0.708 0.75,0.708 true 1.802,1.25 2.094,0.688 2.094,0.688 2.302,0.688 true 0.146,2.542 0.396,2.74 0.25,0.198 10 false *1 2.354,0.604 2.719,0.771 0.365,0.167 10 false LP- 0.354,0.625 0.74,0.792 0.385,0.167 10 false BSL+

Remove the outer rear view mirror assembly LH (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL).


b.

Apply battery voltage to the terminal of the outer rear view mirror assembly LH, and check that the blind spot monitor indicator turns on.

Standard:
Connection Specified Condition
Battery positive (+) → 9 (BSL+)
Battery negative (-) → 5 (LP-)
Indicator turns on


Text in Illustration
*1 Blind Spot Monitor Indicator LH



OK

NG

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.
E231117E04
1.031,0.906 1.135,0.438 1.135,0.438 1.198,0.438 true 1.719,0.906 1.823,0.438 1.823,0.438 1.896,0.438 true 1.719,3.021 1.26,3.188 1.26,3.188 1.188,3.188 true 1.719,2.698 2.167,2.177 2.167,2.177 2.229,2.177 true 0.083,0.063 0.271,0.208 0.188,0.146 10 false *a 1.229,0.354 1.635,0.5 0.406,0.146 10 false BSL+ 0.094,1.771 0.281,1.917 0.188,0.146 10 false *b 1.938,0.365 2.344,0.51 0.406,0.146 10 false LP- 1.042,3.094 1.167,3.24 0.125,0.146 10 false + 2.292,2.083 2.417,2.229 0.125,0.146 10 false -

Remove the outer rear view mirror assembly LH (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL).


b.

Remove the outer rear view mirror glass LH (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>REMOVAL).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (BSL+) - 7 (+) Always Below 1 Ω
5 (LP-) - 5 (-) Always Below 1 Ω


Text in Illustration
*a Vehicle Side
*b Outer Rear View Mirror Glass LH Side



OK

REPLACE OUTER REAR VIEW MIRROR GLASS LH (BLIND SPOT MONITOR INDICATOR LH)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH