Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM27L0U _57 Power Source / Network _049335 NETWORKING _0235802 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Open in One Side of CAN Branch Line  


DESCRIPTION

If 2 or more ECUs and/or sensors do not appear on the Techstream "Bus Check" screen, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).

Symptom Trouble Area
2 or more ECUs and/or sensors do not appear on the Techstream "Bus Check" screen.
·

Air conditioning amplifier assembly

·

4 wheel drive control ECU (4WD control ECU)*1

·

Bus buffer ECU*2

·

Network gateway ECU*3

·

Center airbag sensor assembly

·

Steering angle sensor

·

Main body ECU (cowl side junction block LH)

·

Power steering ECU assembly

·

Suspension control ECU*4

·

Brake actuator assembly (skid control ECU)

·

CAN branch wire or connector



*1: for 4WD

*2: w/ Bus Buffer ECU

*3: w/ Network Gateway ECU

*4: w/ Air Suspension System

WIRING DIAGRAM

C242851E01
5.836,1.484 6.109,1.620 0.272,0.137 10 A27 5.836,1.633 6.168,1.770 0.331,0.137 10 ECM 5.595,1.252 6.058,1.389 0.463,0.137 10 CANL 5.595,0.681 6.058,0.818 0.463,0.137 10 CANH 0.643,1.633 2.263,1.946 1.620,0.312 10 Air Conditioning Amplifier Assembly 0.643,1.484 0.915,1.620 0.272,0.137 10 H24 5.336,1.074 5.507,1.211 0.172,0.137 10 11 5.336,0.695 5.507,0.832 0.172,0.137 10 10 1.903,1.074 2.075,1.211 0.172,0.137 10 12 1.903,0.695 2.075,0.832 0.172,0.137 10 11 3.991,1.074 4.162,1.211 0.172,0.137 10 14 3.991,0.695 4.086,0.832 0.095,0.137 10 3 3.097,1.074 3.269,1.211 0.172,0.137 10 12 3.174,0.695 3.270,0.832 0.095,0.137 10 1 1.377,1.163 1.771,1.300 0.394,0.137 10 CANL 1.356,0.78 1.770,0.917 0.415,0.137 10 CANH 3.991,4.141 4.162,4.277 0.172,0.137 10 15 3.991,3.762 4.086,3.899 0.095,0.137 10 4 3.097,4.141 3.269,4.277 0.172,0.137 10 17 3.174,3.762 3.270,3.899 0.095,0.137 10 6 3.097,2.732 3.269,2.868 0.172,0.137 10 16 1.903,4.141 2.075,4.277 0.172,0.137 10 15 1.903,3.762 2.088,3.899 0.185,0.137 10 16 5.304,3.161 5.576,3.298 0.272,0.137 10 A28 5.304,3.296 7.021,3.608 1.717,0.312 10 4 Wheel Drive Control ECU (4WD Control ECU)*1 0.844,3.161 1.116,3.298 0.272,0.137 10 H66 0.844,3.296 1.975,3.435 1.132,0.139 10 Bus Buffer ECU*2 0.844,4.585 1.428,4.721 0.585,0.137 10 H120 0.844,4.719 2.433,4.858 1.590,0.139 10 Network Gateway ECU*3 5.336,2.732 5.507,2.868 0.172,0.137 10 20 5.336,2.353 5.507,2.490 0.172,0.137 10 19 1.903,2.732 2.075,2.868 0.172,0.137 10 2 1.903,2.353 2.075,2.490 0.172,0.137 10 3 3.991,2.732 4.162,2.868 0.172,0.137 10 13 3.991,2.353 4.086,2.490 0.095,0.137 10 2 3.174,2.353 3.270,2.490 0.095,0.137 10 5 1.405,2.821 1.771,2.958 0.366,0.137 10 CAN- 1.377,2.438 1.771,2.575 0.394,0.137 10 CAN+ 5.595,2.821 5.989,2.958 0.394,0.137 10 CANL 5.595,2.438 6.009,2.575 0.415,0.137 10 CANH 5.409,7.669 5.681,7.806 0.272,0.137 10 H6 5.409,7.804 6.818,7.954 1.409,0.150 10 Steering Angle Sensor 1.226,7.669 1.499,7.806 0.272,0.137 10 H19 1.226,7.804 1.603,7.943 0.377,0.139 10 DLC3 5.41,7.24 5.508,7.376 0.097,0.137 10 9 5.336,6.861 5.507,6.998 0.172,0.137 10 10 1.903,7.24 2.075,7.376 0.172,0.137 10 14 1.903,6.861 2.075,6.998 0.172,0.137 10 6 3.991,7.24 4.162,7.376 0.172,0.137 10 15 3.991,6.861 4.086,6.998 0.095,0.137 10 4 3.097,7.24 3.269,7.376 0.172,0.137 10 14 3.174,6.861 3.270,6.998 0.095,0.137 10 3 1.377,7.329 1.771,7.465 0.394,0.137 10 CANL 1.356,6.946 1.770,7.083 0.415,0.137 10 CANH 5.595,7.329 5.989,7.465 0.394,0.137 10 CANL 5.595,6.946 6.009,7.083 0.415,0.137 10 CANH 0.778,5.994 1.050,6.131 0.272,0.137 10 H56 0.778,6.129 2.139,6.479 1.361,0.350 10 Center Airbag Sensor Assembly 1.903,5.564 2.075,5.701 0.172,0.137 10 22 1.903,5.186 2.075,5.323 0.172,0.137 10 13 3.991,5.564 4.162,5.701 0.172,0.137 10 16 3.991,5.186 4.086,5.323 0.095,0.137 10 5 3.097,5.564 3.269,5.701 0.172,0.137 10 12 3.174,5.186 3.270,5.323 0.095,0.137 10 1 1.377,5.653 1.771,5.790 0.394,0.137 10 CANL 1.352,5.271 1.770,5.408 0.418,0.137 10 CANH 2.889,4.719 4.479,4.865 1.590,0.145 10 No. 2 Junction Connector 2.889,4.584 3.279,4.721 0.390,0.137 10 H115 4.15,8.245 5.740,8.391 1.590,0.145 10 No. 1 Junction Connector 4.15,8.111 4.540,8.247 0.390,0.137 10 H119 0.192,8.312 1.584,8.450 1.392,0.139 10 *2: w/ Bus Buffer ECU 0.192,8.585 2.025,8.731 1.833,0.146 10 *3: w/ Network Gateway ECU 0.192,8.067 0.980,8.205 0.788,0.139 10 *1: for 4WD 1.401,4.241 1.771,4.378 0.369,0.137 10 CA1L 1.38,3.859 1.771,3.996 0.390,0.137 10 CA1H

C242852E01
5.327,1.69 6.973,1.997 1.645,0.306 10 Main Body ECU (Cowl Side Junction Block LH) 5.327,1.548 5.600,1.685 0.272,0.137 10 H2 5.595,1.23 6.058,1.367 0.463,0.137 10 CANL 5.595,0.848 6.058,0.984 0.463,0.137 10 CANH 0.745,1.69 2.694,1.835 1.949,0.144 10 Power Steering ECU Assembly 0.745,1.548 1.110,1.685 0.365,0.137 10 H117 5.41,1.141 5.508,1.278 0.097,0.137 10 6 5.41,0.763 5.508,0.900 0.097,0.137 10 5 1.903,1.141 2.075,1.278 0.172,0.137 10 2 1.903,0.763 2.075,0.900 0.172,0.137 10 1 3.991,1.141 4.162,1.278 0.172,0.137 10 17 3.991,0.763 4.086,0.900 0.095,0.137 10 6 3.097,1.141 3.269,1.278 0.172,0.137 10 18 3.175,0.763 3.270,0.900 0.095,0.137 10 7 1.377,1.23 1.771,1.367 0.394,0.137 10 CANL 1.356,0.848 1.770,0.984 0.415,0.137 10 CANH 3.991,2.967 4.162,3.104 0.172,0.137 10 13 3.991,2.589 4.086,2.726 0.095,0.137 10 2 3.097,2.967 3.269,3.104 0.172,0.137 10 20 3.175,2.589 3.270,2.726 0.095,0.137 10 9 0.844,3.397 1.116,3.533 0.272,0.137 10 A19 0.844,3.532 2.436,3.837 1.592,0.305 10 Brake Actuator Assembly (Skid Control ECU) 1.903,2.967 2.075,3.104 0.172,0.137 10 13 1.903,2.589 2.075,2.726 0.172,0.137 10 12 1.381,3.056 1.771,3.193 0.389,0.137 10 CANL 1.358,2.674 1.770,2.810 0.412,0.137 10 CANH 0.844,5.325 1.134,5.462 0.291,0.137 10 O16 0.844,5.46 2.436,5.602 1.592,0.142 10 Suspension Control ECU 1.903,4.924 2.075,5.061 0.172,0.137 10 8 1.903,4.335 2.075,4.472 0.172,0.137 10 7 1.381,5.013 1.771,5.150 0.389,0.137 10 CANL 1.358,4.42 1.770,4.557 0.412,0.137 10 CANH 5.336,6.492 5.507,6.629 0.172,0.137 10 34 5.336,5.915 5.507,6.052 0.172,0.137 10 33 5.595,6.668 5.989,6.804 0.394,0.137 10 CANL 5.595,5.915 6.009,6.052 0.415,0.137 10 CANH 2.889,3.518 4.479,3.663 1.590,0.145 10 No. 1 Junction Connector 2.889,3.383 3.279,3.520 0.390,0.137 10 H119 2.889,6.949 4.479,7.094 1.590,0.145 10 No. 4 Junction Connector 3.982,6.002 4.268,6.139 0.286,0.137 10 O41 4.077,5.785 4.175,5.922 0.099,0.137 10 1 3.982,6.586 4.268,6.723 0.286,0.137 10 O41 4.077,6.369 4.175,6.506 0.099,0.137 10 7 3.982,4.433 4.268,4.570 0.286,0.137 10 O41 4.077,4.216 4.175,4.353 0.099,0.137 10 2 3.982,5.017 4.268,5.154 0.286,0.137 10 O41 4.077,4.8 4.175,4.937 0.099,0.137 10 8 2.994,4.433 3.281,4.570 0.286,0.137 10 O42 3.089,4.216 3.188,4.353 0.099,0.137 10 6 2.994,5.017 3.281,5.154 0.286,0.137 10 O42 3.052,4.8 3.224,4.937 0.173,0.137 10 12 5.431,6.895 5.722,7.032 0.291,0.137 10 H37 5.431,7.03 6.638,7.334 1.206,0.304 10 Combination Meter Assembly 0.157,0.112 2.364,0.372 2.207,0.259 12 w/ Air Suspension System:

C242853E01
5.327,1.861 5.600,1.998 0.272,0.137 10 H2 5.327,2.003 6.973,2.309 1.645,0.306 10 Main Body ECU (Cowl Side Junction Block LH) 5.595,1.543 6.058,1.679 0.463,0.137 10 CANL 5.595,1.16 6.058,1.297 0.463,0.137 10 CANH 0.745,2.003 2.694,2.147 1.949,0.144 10 Power Steering ECU Assembly 0.745,1.861 1.110,1.998 0.365,0.137 10 H117 5.41,1.453 5.508,1.590 0.097,0.137 10 6 5.41,1.075 5.508,1.212 0.097,0.137 10 5 1.903,1.453 2.075,1.590 0.172,0.137 10 2 1.903,1.075 2.075,1.212 0.172,0.137 10 1 3.991,1.453 4.162,1.590 0.172,0.137 10 17 3.991,1.075 4.086,1.212 0.095,0.137 10 6 3.097,1.453 3.269,1.590 0.172,0.137 10 18 3.175,1.075 3.270,1.212 0.095,0.137 10 7 1.377,1.543 1.771,1.679 0.394,0.137 10 CANL 1.356,1.16 1.770,1.297 0.415,0.137 10 CANH 3.991,3.28 4.162,3.417 0.172,0.137 10 13 3.991,2.902 4.086,3.038 0.095,0.137 10 2 3.097,3.279 3.269,3.416 0.172,0.137 10 20 3.175,2.901 3.270,3.038 0.095,0.137 10 9 0.844,3.709 1.116,3.846 0.272,0.137 10 A19 0.844,3.844 2.436,4.149 1.592,0.305 10 Brake Actuator Assembly (Skid Control ECU) 1.903,3.279 2.075,3.416 0.172,0.137 10 13 1.903,2.901 2.075,3.038 0.172,0.137 10 12 1.381,3.369 1.771,3.505 0.389,0.137 10 CANL 1.358,2.986 1.770,3.123 0.412,0.137 10 CANH 5.336,3.286 5.507,3.422 0.172,0.137 10 34 5.336,2.905 5.507,3.042 0.172,0.137 10 33 5.595,3.461 5.989,3.598 0.394,0.137 10 CANL 5.595,2.905 6.009,3.042 0.415,0.137 10 CANH 2.889,3.83 4.479,3.976 1.590,0.145 10 No. 1 Junction Connector 2.889,3.695 3.279,3.832 0.390,0.137 10 H119 5.431,3.688 5.722,3.825 0.291,0.137 10 H37 5.431,3.823 6.638,4.127 1.206,0.304 10 Combination Meter Assembly 0.157,0.113 2.364,0.372 2.207,0.259 12 w/o Air Suspension System:

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the following inspection for the ECUs (sensors) which are displayed on the Techstream. If a malfunction cannot be identified, perform the following inspections for the ECUs (sensors) connected to the CAN communication system.

·

Do not remove the combination meter assembly and ECM as they are the end parts of the circuit. If removed, CAN communication will not be possible.

·

The open circuit confirmation of the combination meter assembly, ECM and CAN main wire is performed in the Check CAN Bus Line procedure of "How to Proceed with Troubleshooting". This inspection only has procedures for checking for an open circuit on one side of a CAN branch wire.



PROCEDURE

1.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the H24 air conditioning amplifier assembly connector.


b.

Select "CAN Bus Check" on the Techstream (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Air Conditioning Amplifier" is not displayed on the Techstream A
Several ECUs and sensors in addition to "Air Conditioning Amplifier" are displayed on the Techstream B



A

2.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE)

B

3.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (4WD CONTROL ECU)
2.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE)
a.
U153695E03
1.781,1.365 2.24,1.896 2.24,1.896 2.333,1.896 true 1.698,1.365 1.25,1.896 1.25,1.896 1.156,1.896 true 0.375,1.302 0.656,1.448 0.281,0.146 10 false H24 0.75,1.813 1.135,1.958 0.385,0.146 10 false CANL 2.385,1.802 2.802,1.948 0.417,0.146 10 false CANH 0.052,0.042 0.333,0.188 0.281,0.146 10 false *a

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H24-11 (CANH) - H24-12 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY)

3.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (4WD CONTROL ECU)
NOTICE:

For vehicles without an 4WD, go to "Check for Open in One Side of CAN Branch Wire (Bus Buffer ECU)".


a.

Disconnect the A28 4 wheel drive control ECU (4WD control ECU) connector.


b.

Select "CAN Bus Check" on the Techstream (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Four Wheel Drive Control" is not displayed on the Techstream A
Several ECUs and sensors in addition to "Four Wheel Drive Control" are displayed on the Techstream B



A

4.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (4WD CONTROL ECU CAN BRANCH WIRE)

B

5.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (BUS BUFFER ECU)
4.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (4WD CONTROL ECU CAN BRANCH WIRE)
a.
U153824E01
1.02,1.14 0.808,1.545 0.808,1.545 0.69,1.545 false 0.659,0.898 0.719,0.898 0.719,0.898 0.928,1.115 false 0.178,1.468 0.597,1.610 0.420,0.142 10 CANH 0.178,0.818 0.597,0.960 0.420,0.142 10 CANL 0.08,0.05 0.500,0.192 0.420,0.142 10 *a 2.86,1.106 3.131,1.248 0.272,0.142 10 A28

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A28-19 (CANH) - A28-20 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to 4 Wheel Drive Control ECU [4WD Control ECU])



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU (4WD CONTROL ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (4WD CONTROL ECU)

5.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (BUS BUFFER ECU)
NOTICE:

For vehicles without an bus buffer ECU, go to "Check for Open in One Side of CAN Branch Wire (Network Gateway ECU)".


a.

Disconnect the H66 bus buffer ECU connector.


b.

Select "CAN Bus Check" on the Techstream (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Accessory Gateway" is not displayed on the Techstream A
Several ECUs and sensors in addition to "Accessory Gateway" are displayed on the Techstream B



A

6.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (BUS BUFFER ECU CAN BRANCH WIRE)

B

7.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (NETWORK GATEWAY ECU)
6.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (BUS BUFFER ECU CAN BRANCH WIRE)
a.
U153828E01
0.636,0.826 1.034,0.966 0.398,0.140 10 CAN+ 0.801,1.651 1.168,1.789 0.368,0.137 10 CAN- 2.544,1.107 2.817,1.245 0.273,0.138 10 H66 0.063,0.062 0.333,0.228 0.270,0.166 10 *a 1.395,1.157 1.192,0.912 1.192,0.912 1.117,0.912 false 1.262,1.723 1.336,1.723 1.336,1.723 1.745,1.256 false

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H66-3 (CAN+) - H66-2 (CAN-) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Bus Buffer ECU)



OK

REPLACE BUS BUFFER ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (BUS BUFFER ECU)

7.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (NETWORK GATEWAY ECU)
NOTICE:

For vehicles without an network gateway ECU, go to "Check for Open in One Side of CAN Branch Wire (Center Airbag Sensor Assembly)".


a.

Disconnect the H120 network gateway ECU connector.


b.

Select "CAN Bus Check" on the Techstream (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"CAN Gateway1" is not displayed on the Techstream A
Several ECUs and sensors in addition to "CAN Gateway1" are displayed on the Techstream B



A

8.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (NETWORK GATEWAY ECU CAN BRANCH WIRE)

B

9.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY)
8.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (NETWORK GATEWAY ECU CAN BRANCH WIRE)
a.
U153772E01
2.741,1.136 3.098,1.273 0.357,0.137 10 H120 1.246,1.243 1.037,1.018 1.037,1.018 0.914,1.018 false 1.031,1.637 1.103,1.637 1.103,1.637 1.355,1.293 false 0.424,0.944 0.813,1.081 0.389,0.137 10 CA1H 0.582,1.551 0.970,1.688 0.389,0.137 10 CA1L 0.07,0.056 0.371,0.193 0.301,0.137 10 *a

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H120-16 (CA1H) - H120-15 (CA1L) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Network Gateway ECU)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (NETWORK GATEWAY ECU)

9.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the H56 center airbag sensor assembly connector.


b.

Select "CAN Bus Check" on the Techstream (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Airbag" is not displayed on the Techstream A
Several ECUs and sensors in addition to "Airbag" are displayed on the Techstream B



A

10.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)

B

11.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR)
10.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)
a.
U153693E02
2.031,1 2.5,0.417 2.5,0.417 2.583,0.417 true 2.135,1.271 2.49,1.677 2.49,1.677 2.573,1.677 true 0.427,1.01 0.698,1.156 0.271,0.146 10 false H56 2.646,0.333 3.083,0.51 0.438,0.177 10 false CANH 0.125,0.073 0.333,0.25 0.208,0.177 10 false *a 2.615,1.615 3.021,1.792 0.406,0.177 10 false CANL

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H56-13 (CANH) - H56-22 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Center Airbag Sensor Assembly)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY)

11.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR)
a.

Disconnect the H6 steering angle sensor connector.


b.

Select "CAN Bus Check" on the Techstream (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Spiral cable (Steering Angle Sensor)" is not displayed on the Techstream A
Several ECUs and sensors in addition to "Spiral cable (Steering Angle Sensor)" are displayed on the Techstream B



A

12.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)

B

13.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU)
12.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)
a.
U153835E01
1.172,1.309 0.944,1.537 0.944,1.537 0.834,1.537 false 1.008,1.802 1.068,1.802 1.068,1.802 1.307,1.309 false 0.338,1.451 0.759,1.594 0.421,0.143 10 CANH 2.789,1.199 2.984,1.342 0.195,0.143 10 H6 0.51,1.72 0.931,1.863 0.421,0.143 10 CANL 0.058,0.035 0.253,0.178 0.195,0.143 10 *a

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H6-10 (CANH) - H6-9 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Steering Angle Sensor)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (STEERING ANGLE SENSOR)

13.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU)
a.

Disconnect the H2 main body ECU (cowl side junction block LH) connector.


b.

Select "CAN Bus Check" on the Techstream (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Main Body" is not displayed on the Techstream A
Several ECUs and sensors in addition to "Main Body" are displayed on the Techstream B



A

14.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU CAN BRANCH WIRE)

B

15.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY)
14.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU CAN BRANCH WIRE)
a.
U153837E01
1.404,1.351 1.138,1.617 1.138,1.617 1,1.617 false 1.249,1.973 1.356,1.973 1.356,1.973 1.537,1.351 false 0.495,1.541 0.916,1.678 0.422,0.137 10 CANH 0.74,1.896 1.161,2.032 0.422,0.137 10 CANL 2.501,1.178 2.700,1.315 0.199,0.137 10 H2 0.067,0.048 0.267,0.185 0.199,0.137 10 *a

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H2-5 (CANH) - H2-6 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH])



OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (MAIN BODY ECU)

15.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY)
a.

Disconnect the H117 power steering ECU assembly connector.


b.

Select "CAN Bus Check" on the Techstream (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Power Steering (EPS)" is not displayed on the Techstream A
Several ECUs and sensors in addition to "Power Steering (EPS)" are displayed on the Techstream B



A

16.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY CAN BRANCH WIRE)

B

17.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SUSPENSION CONTROL ECU)
16.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY CAN BRANCH WIRE)
a.
U154144E02
1.302,1.438 1.479,1.771 1.479,1.771 1.573,1.771 true 1.115,1.438 0.938,1.771 0.938,1.771 0.844,1.771 true 0.094,0.063 0.333,0.281 0.24,0.219 10 false *a 1.635,1.719 2.083,1.927 0.448,0.208 10 false CANL 0.417,1.677 0.865,1.885 0.448,0.208 10 false CANH 1.604,0.406 1.958,0.542 0.354,0.135 10 false H117

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H117-1 (CANH) - H117-2 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (POWER STEERING ECU)

17.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SUSPENSION CONTROL ECU)
NOTICE:

For vehicles without an air suspension control system, go to "Check for Open in One Side of CAN Branch Wire (Skid Control ECU)".


a.

Disconnect the O16 suspension control ECU connector.


b.

Select "CAN Bus Check" on the Techstream (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Suspension Control (Air Suspension)" is not displayed on the Techstream A
Several ECUs and sensors in addition to "Suspension Control (Air Suspension)" are displayed on the Techstream B



A

18.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SUSPENSION CONTROL ECU CAN BRANCH WIRE)

B

19.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU)
18.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SUSPENSION CONTROL ECU CAN BRANCH WIRE)
a.
U153871E01
1.06,1.462 0.866,1.634 0.866,1.634 0.769,1.634 false 0.939,1.989 1.044,1.989 1.044,1.989 1.195,1.462 false 0.077,0.049 0.255,0.189 0.178,0.140 10 *a 0.256,1.55 0.673,1.691 0.417,0.140 10 CANH 0.423,1.909 0.840,2.049 0.417,0.140 10 CANL 2.717,1.235 2.997,1.375 0.280,0.140 10 O16

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
O16-7 (CANH) - O16-8 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Suspension Control ECU)



OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (SUSPENSION CONTROL ECU)

19.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU)
a.
U153873E01
1.246,1.152 1.073,0.726 1.073,0.726 0.961,0.726 false 1.342,1.161 1.093,1.858 1.093,1.858 0.961,1.858 false 0.08,0.054 0.252,0.214 0.172,0.159 10 *a 1.561,0.61 1.829,0.748 0.268,0.137 10 A19 0.432,1.788 0.865,1.925 0.433,0.137 10 CANH 0.478,0.648 0.874,0.785 0.395,0.137 10 CANL

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the A19 brake actuator assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A19-12 (CANH) - A19-13 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU)