Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235847 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1780  Front Occupant Classification Sensor LH Circuit Malfunction  


DESCRIPTION

The front occupant detection sensor LH circuit consists of the occupant classification ECU and the front occupant detection sensor LH.

DTC B1780 is stored when a malfunction is detected in the front occupant detection sensor LH circuit.

DTC Code DTC Detection Condition Trouble Area
B1780 One of following conditions is met:
·

Occupant classification ECU receives line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to +B signal in front occupant detection sensor LH circuit for 2 seconds

·

Front occupant detection sensor LH malfunction

·

Occupant classification ECU malfunction


·

Front seat assembly RH (Front occupant detection sensor LH)

·

Front seat wire RH

·

Occupant classification ECU



HINT:
·

When DTC B1650/32 is detected as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1780 of the occupant classification system.

·

Use the Techstream to check for DTCs of the occupant classification ECU, otherwise the DTC cannot be read.



WIRING DIAGRAM

B151586E19
1.577,1.701 1.733,1.882 0.156,0.181 10 2 1.577,0.389 1.733,0.570 0.156,0.181 10 1 1.577,3.036 1.733,3.217 0.156,0.181 10 3 5.466,0.392 5.685,0.618 0.219,0.225 10 11 5.218,3.796 5.508,3.977 0.290,0.181 10 W1 5.532,1.694 5.688,1.876 0.156,0.181 10 7 5.532,3.028 5.736,3.209 0.205,0.181 10 1 5.732,0.471 6.143,0.652 0.411,0.181 10 SVC1 5.732,1.798 6.087,1.979 0.355,0.181 10 SIG1 5.732,3.127 6.169,3.308 0.438,0.181 10 SGD1 1.095,0.471 1.507,0.652 0.411,0.181 10 SVC1 1.119,1.798 1.474,1.979 0.355,0.181 10 SIG1 1.079,3.127 1.517,3.308 0.438,0.181 10 SGD1 0.136,3.964 2.550,4.164 2.414,0.200 10 Front Occupant Detection Sensor LH 5.229,3.964 7.029,4.145 1.800,0.181 10 Occupant Classification ECU 0.136,3.796 0.453,3.977 0.317,0.181 10 W2

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

If troubleshooting (wire harness inspection) is difficult to perform, remove the front seat RH installation bolts to see the undersurface of the seat cushion.

·

In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause problems, such as seat rail deformation. Hold the seat up only for as long as necessary.



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear any DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:
·

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

·

Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.




c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Using the Techstream, check for DTCs of the occupant classification ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1780 is not output.


HINT:

DTCs other than DTC B1780 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTION OF CONNECTOR
2.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the occupant classification ECU and the front occupant detection sensor LH.

OK:

Connectors are properly connected.




OK

3.CHECK CONNECTOR

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTOR
a.

Check that the connectors (on the occupant classification ECU side and front occupant detection sensor LH side) are not damaged (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

OK:

Connectors are not deformed or damaged.




OK

4.CHECK FRONT SEAT WIRE RH

NG

REPLACE FRONT SEAT WIRE RH

4.CHECK FRONT SEAT WIRE RH
U153559E01
3.85,1.031 4.251,1.199 0.400,0.168 10 SGD1 3.814,1.988 4.160,2.156 0.346,0.168 10 SIG1 6.551,1.309 7.061,1.640 0.510,0.331 10 Service Wire 3.729,1.528 3.926,1.227 false 3.727,1.671 3.889,1.964 false 4.253,1.988 4.645,2.156 0.393,0.168 10 SVC1 4.096,1.671 4.328,1.964 false 2.827,1.434 3.091,1.587 0.264,0.153 10 W1 5.031,1.434 5.296,1.587 0.264,0.153 10 W2 0.518,1.084 0.659,1.246 0.142,0.162 10 D 0.83,1.262 0.968,1.424 0.138,0.162 10 C 5.263,1.979 5.672,2.141 0.409,0.162 10 SVC1 6.517,1.828 6.926,1.990 0.409,0.162 10 SGD1 1.299,1.264 1.431,1.436 0.132,0.172 10 B 1.633,1.084 1.772,1.245 0.139,0.161 10 A 1.473,1.37 2.327,1.870 0.853,0.500 10 Occupant Classification ECU 4.71,0.049 7.153,0.588 2.443,0.538 10 Front view of wire harness connector: (to Front Occupant Detection Sensor LH) 2.279,0.049 4.605,0.430 2.326,0.380 10 Front view of wire harness connector: (to Occupant Classification ECU) 0.046,1.443 1.035,1.999 0.989,0.555 10 Front Occupant Classification Sensor LH 4.763,1.124 5.571,1.290 0.808,0.166 10 Connector C 2.562,1.134 3.352,1.299 0.789,0.166 10 Connector B 0.339,0.143 1.028,0.493 0.689,0.351 10 Front Seat Wire RH 5.953,1.625 5.596,1.979 false 6.139,1.625 6.496,1.899 false 5.911,2.042 6.249,2.210 0.337,0.168 10 SIG1 6.062,1.625 6.062,2.042 false 6.286,1.973 6.356,2.26 6.356,2.26 6.416,2.26 false 6.356,1.259 6.464,1.391 6.464,1.391 6.523,1.391 false 1.176,1.102 1.176,0.255 1.176,0.255 1.045,0.255 false 6.439,2.174 6.949,2.505 0.510,0.331 10 Service Wire

a.

Disconnect the connectors from the occupant classification ECU and the front occupant detection sensor LH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
W1-1 (SGD1) - Body ground Ignition switch ON Below 1 V
W1-7 (SIG1) - Body ground
W1-11 (SVC1) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using service wires, connect terminals 1 (SVC1) and 3 (SGD1), and connect terminals 2 (SIG1) and 3 (SGD1) of connector C.

NOTICE:

Do not forcibly insert the service wires into the terminals of the connector.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W1-7 (SIG1) - W1-1 (SGD1) Always Below 1 Ω
W1-11 (SVC1) - W1-1 (SGD1)



i.

Disconnect the service wires from connector C.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W1-7 (SIG1) - W1-1 (SGD1) Always 1 MΩ or higher
W1-11 (SVC1) - W1-1 (SGD1)
W1-1 (SGD1) - Body ground
W1-7 (SIG1) - Body ground
W1-11 (SVC1) - Body ground
W1-7 (SIG1) - W1-11 (SVC1)




OK

5.CHECK FOR DTC

NG

REPLACE FRONT SEAT WIRE RH

5.CHECK FOR DTC
a.

Connect the connectors to the occupant classification ECU and the front occupant detection sensor LH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear any DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:
·

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

·

Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.




e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Using the Techstream, check for DTCs of the occupant classification ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1780 is not output.


HINT:

DTCs other than DTC B1780 may be output at this time, but they are not related to this check.




OK

NG

6.REPLACE OCCUPANT CLASSIFICATION ECU
6.REPLACE OCCUPANT CLASSIFICATION ECU
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the occupant classification ECU.


HINT:

Perform the inspection using parts from a normal vehicle when possible.




NEXT

7.PERFORM ZERO POINT CALIBRATION
7.PERFORM ZERO POINT CALIBRATION
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Using the Techstream, perform the zero point calibration (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



OK

8.PERFORM SENSITIVITY CHECK

NG

10.REPLACE FRONT SEAT ASSEMBLY RH
8.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




OK

9.CHECK FOR DTC

NG

10.REPLACE FRONT SEAT ASSEMBLY RH
9.CHECK FOR DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear any DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:
·

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

·

Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.




c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Using the Techstream, check for DTCs of the occupant classification ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1780 is not output.


HINT:

DTCs other than DTC B1780 may be output at this time, but they are not related to this check.




OK

END

NG

10.REPLACE FRONT SEAT ASSEMBLY RH
10.REPLACE FRONT SEAT ASSEMBLY RH
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the front seat assembly RH.



HINT:

Perform the inspection using parts from a normal vehicle when possible.



NEXT

11.PERFORM ZERO POINT CALIBRATION
11.PERFORM ZERO POINT CALIBRATION
a.

Connect the Techstream to the DLC3.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Using the Techstream, perform the zero point calibration (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



NEXT

12.PERFORM SENSITIVITY CHECK
12.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




NEXT

END