Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235847 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1787  Rear Occupant Classification Sensor LH Collision Detection  


DESCRIPTION

DTC B1787 is stored when the occupant classification ECU receives a collision detection signal, which is sent by the rear occupant detection sensor LH when an accident occurs.

DTC B1787 is also stored when the front seat assembly RH is subjected to a strong impact, even if an actual accident has not occurred.

However, when the occupant classification ECU outputs a collision detection signal, even if the vehicle is not in a collision, DTC B1787 can be cleared by conducting the zero point calibration and sensitivity check.

Therefore, if DTC B1787 is stored, first perform the zero point calibration and sensitivity check.

DTC Code DTC Detection Condition Trouble Area
B1787 Either of following conditions is met:
·

Occupant classification ECU receives collision detection signal, which is sent by rear occupant detection sensor LH when accident occurs

·

Front seat assembly RH is subjected to strong impact, even if actual accident has not occurred


·

Front seat assembly RH (Rear occupant detection sensor LH)

·

Occupant classification ECU



HINT:
·

When DTC B1650/32 is stored as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1787 of the occupant classification system.

·

Use the Techstream to check for DTCs of the occupant classification ECU, otherwise the DTCs cannot be read.



WIRING DIAGRAM

B151586E21
1.577,1.701 1.733,1.882 0.156,0.181 10 2 1.577,0.389 1.733,0.570 0.156,0.181 10 1 1.577,3.036 1.733,3.217 0.156,0.181 10 3 5.532,0.392 5.703,0.574 0.171,0.181 10 5 5.218,3.796 5.508,3.977 0.290,0.181 10 W1 5.532,1.694 5.688,1.876 0.156,0.181 10 9 5.494,3.028 5.699,3.209 0.205,0.181 10 3 5.732,0.471 6.143,0.652 0.411,0.181 10 SVC3 5.732,1.798 6.087,1.979 0.355,0.181 10 SIG3 5.732,3.127 6.169,3.308 0.438,0.181 10 SGD3 1.095,0.471 1.507,0.652 0.411,0.181 10 SVC3 1.119,1.798 1.474,1.979 0.355,0.181 10 SIG3 1.079,3.127 1.517,3.308 0.438,0.181 10 SGD3 0.136,3.964 2.525,4.164 2.390,0.200 10 Rear Occupant Detection Sensor LH 5.229,3.964 7.029,4.145 1.800,0.181 10 Occupant Classification ECU 0.136,3.796 0.453,3.977 0.317,0.181 10 W4

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear any DTCs stored in the center airbag sensor (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).


c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Using the Techstream, check for DTCs of the occupant classification ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1787 is not output.


HINT:

DTCs other than DTC B1787 may be output at this time, but they are not related to this check.




OK

NG

2.PERFORM ZERO POINT CALIBRATION
2.PERFORM ZERO POINT CALIBRATION
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Using the Techstream, perform the zero point calibration (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



OK

3.PERFORM SENSITIVITY CHECK

NG

5.REPLACE FRONT SEAT ASSEMBLY RH
3.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




OK

4.CHECK FOR DTC

NG

5.REPLACE FRONT SEAT ASSEMBLY RH
4.CHECK FOR DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear any DTCs stored in the center airbag sensor (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).


c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Using the Techstream, check for DTCs of the occupant classification ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1787 is not output.


HINT:

DTCs other than DTC B1787 may be output at this time, but they are not related to this check.




OK

END

NG

5.REPLACE FRONT SEAT ASSEMBLY RH
5.REPLACE FRONT SEAT ASSEMBLY RH
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the front seat assembly RH.


HINT:

Perform the inspection using parts from a normal vehicle when possible.




NEXT

6.PERFORM ZERO POINT CALIBRATION
6.PERFORM ZERO POINT CALIBRATION
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Using the Techstream, perform the zero point calibration (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



OK

7.PERFORM SENSITIVITY CHECK

NG

9.REPLACE OCCUPANT CLASSIFICATION ECU
7.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




OK

8.CHECK FOR DTC

NG

9.REPLACE OCCUPANT CLASSIFICATION ECU
8.CHECK FOR DTC
a.

Connect the connectors to the occupant classification ECU and the rear occupant detection sensor LH.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Clear any DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:
·

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

·

Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.




d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Using the Techstream, check for DTCs of the occupant classification ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1787 is not output.


HINT:

DTCs other than DTC B1787 may be output at this time, but they are not related to this check.




OK

END

NG

9.REPLACE OCCUPANT CLASSIFICATION ECU
9.REPLACE OCCUPANT CLASSIFICATION ECU
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the occupant classification ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL).

HINT:

Perform the inspection using parts from a normal vehicle when possible.




NEXT

10.PERFORM ZERO POINT CALIBRATION
10.PERFORM ZERO POINT CALIBRATION
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Using the Techstream, perform the zero point calibration (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



NEXT

11.PERFORM SENSITIVITY CHECK
11.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




NEXT

END