Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235847 OCCUPANT CLASSIFICATION SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  Trouble in Passenger Airbag ON/OFF Indicator  


DESCRIPTION

The occupant classification system detects the front passenger seat condition. It then informs a passenger of the front passenger airbag assembly and front seat side airbag assembly condition (activated/not activated) with the passenger airbag ON/OFF indicator.

HINT:

Approximately 6 seconds after the ignition switch is turned ON, the passenger airbag ON/OFF indicator will be on/off depending on the conditions listed below.


Front Passenger Seat Condition Passenger Airbag ON/OFF Indicator SRS Warning Light
ON Indicator OFF Indicator
Vacant OFF OFF OFF
Adult is seated. ON OFF OFF
Child is seated. OFF ON OFF
Child restraint system is set. OFF ON OFF
Occupant classification system failure OFF ON ON

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

When the indicator is malfunctioning, if the SRS warning light is off, follow the procedures below as a DTC is not output. If the SRS warning light is on, a DTC is output. Troubleshoot for the output DTC.


PROCEDURE

1.CHECK SRS WARNING LIGHT
a.

Turn the ignition switch to ON, and check the SRS warning light condition.

HINT:

If this trouble occurs, the SRS warning light is off. If the light is on, a DTC is output. Troubleshoot for the output DTC.



OK:

After the primary check period, the SRS warning light goes off.


HINT:

The primary check is performed for approximately 6 seconds after the ignition switch is turned ON.



OK

2.PERFORM ZERO POINT CALIBRATION

NG

2.PERFORM ZERO POINT CALIBRATION
a.

Turn the ignition switch off.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Using the Techstream, perform the zero point calibration (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

OK:

Zero point calibration is completed using the Techstream.




OK

3.PERFORM SENSITIVITY CHECK

NG

4.RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT
3.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




OK

END

NG

4.RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT
4.RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT
a.

Turn the ignition switch off.


b.

Loosen the 4 installation bolts of the front seat assembly RH.


c.

Tighten the 4 installation bolts of the front seat assembly RH to the specified torque.



Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


NEXT

5.PERFORM ZERO POINT CALIBRATION
5.PERFORM ZERO POINT CALIBRATION
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Using the Techstream, perform the zero point calibration (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

OK:

Zero point calibration is completed using the Techstream.




OK

6.PERFORM SENSITIVITY CHECK

NG

7.READ VALUE USING TECHSTREAM (PASSENGER SIDE BUCKLE SWITCH)
6.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




OK

END

NG

7.READ VALUE USING TECHSTREAM (PASSENGER SIDE BUCKLE SWITCH)
7.READ VALUE USING TECHSTREAM (PASSENGER SIDE BUCKLE SWITCH)
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Using the Techstream, read the Data List (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DATA LIST / ACTIVE TEST).

i.

Read the display when the passenger side buckle switch is operated.

Occupant Detection
Tester Display Measure Item/Range Normal Condition Diagnostic Note
Passenger Buckle SW Passenger side buckle switch / Set, Unset or NG Unset: Passenger side seat belt is unfastened
Set: Passenger side seat belt is fastened
NG: Passenger side seat belt is malfunctioning
-

OK:

The Techstream display changed correctly according to the operation of buckle switch.





OK

8.CHECK CONNECTOR

NG

12.CHECK CONNECTOR
8.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Disconnect the connectors from the occupant classification ECU and the 4 occupant classification sensors.


d.

Check that the connectors (on the occupant classification ECU side and 4 occupant classification sensors side) are not damaged.

OK:

Connectors are not deformed or damaged.




OK

9.REPLACE OCCUPANT CLASSIFICATION ECU

NG

REPLACE FRONT SEAT WIRE RH

9.REPLACE OCCUPANT CLASSIFICATION ECU
a.


NEXT

10.PERFORM ZERO POINT CALIBRATION
10.PERFORM ZERO POINT CALIBRATION
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Using the Techstream, perform the zero point calibration (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

OK:

Zero point calibration is completed using the Techstream.




NEXT

11.PERFORM SENSITIVITY CHECK
11.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




NEXT

END

12.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the occupant classification ECU and front seat inner belt RH.


d.

Check that the connectors (on the occupant classification ECU side and front seat inner belt RH side) are not damaged.

OK:

Connectors are not deformed or damaged.




OK

13.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

NG

REPLACE FRONT SEAT WIRE RH

13.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
a.

Replace the front seat inner belt RH (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).



NEXT

14.PERFORM ZERO POINT CALIBRATION
14.PERFORM ZERO POINT CALIBRATION
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Using the Techstream, perform zero point calibration (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

OK:

Zero point calibration is completed using the Techstream.




NEXT

15.PERFORM SENSITIVITY CHECK
15.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




NEXT

END