Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235848 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1805/52  Short in Front Passenger Side Squib Circuit  B1806/52  Open in Front Passenger Side Squib Circuit  B1807/52  Short to GND in Front Passenger Side Squib Circuit  B1808/52  Short to B+ in Front Passenger Side Squib Circuit  


DESCRIPTION

The front passenger side squib circuit consists of the center airbag sensor and the front passenger airbag.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front passenger side squib circuit.

DTC Code Detection Condition Trouble Area
B1805/52 When one of following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the front passenger side squib circuit during primary check.

·

Front passenger side squib malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Front passenger airbag assembly (Front passenger side squib)

·

Center airbag sensor assembly


B1806/52 When one of following conditions is met:
·

The center airbag sensor receives an open circuit signal in the front passenger side squib circuit for 2 seconds.

·

Front passenger side squib malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Front passenger airbag assembly (Front passenger side squib)

·

Center airbag sensor assembly


B1807/52 When one of following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the front passenger side squib circuit for 0.5 seconds.

·

Front passenger side squib malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Front passenger airbag assembly (Front passenger side squib)

·

Center airbag sensor assembly


B1808/52 When one of following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the front passenger side squib circuit for 0.5 seconds.

·

Front passenger side squib malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Front passenger airbag assembly (Front passenger side squib)

·

Center airbag sensor assembly



WIRING DIAGRAM

C146249E45
0.346,3.282 0.649,3.438 0.303,0.156 10 z10 0.343,3.455 2.235,3.611 1.892,0.156 10 Front Passenger Side Squib 5.628,3.288 5.971,3.472 0.343,0.184 10 H56 5.625,3.452 6.998,3.611 1.373,0.159 10 Center Airbag Sensor 1.3,1.106 1.617,1.275 0.317,0.170 10 P+ 5.835,1.106 6.046,1.276 0.211,0.170 10 P+ 1.31,2.297 1.581,2.466 0.270,0.170 10 P- 5.847,2.316 6.058,2.486 0.211,0.170 10 P- 1.651,1.084 1.803,1.282 0.152,0.198 10 1 3.388,2.205 3.540,2.403 0.152,0.198 10 2 1.632,2.297 1.760,2.481 0.128,0.184 10 2 3.384,1.008 3.512,1.192 0.128,0.184 10 1 5.659,1.105 5.780,1.261 0.121,0.156 10 4 5.645,2.282 5.773,2.451 0.128,0.170 10 3 3.31,1.199 3.618,1.396 0.309,0.198 10 Hz1 3.312,2.397 3.620,2.595 0.309,0.198 10 Hz1

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

Perform the simulation method by selecting "check mode" (signal check) with the Techstream (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).



PROCEDURE

1.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connector is properly connected to the front passenger airbag.

OK:

The connector is properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the front passenger airbag.


e.

Check that the No. 2 instrument panel wire connector (on the front passenger airbag side) is not damaged.

OK:

The lock button is not disengaged, or the claw of the lock is not deformed or damaged.




OK

2.CHECK FRONT PASSENGER AIRBAG (FRONT PASSENGER SIDE SQUIB)

NG

REPLACE NO. 2 INSTRUMENT PANEL WIRE

2.CHECK FRONT PASSENGER AIRBAG (FRONT PASSENGER SIDE SQUIB)
a.
U153443E02
0.552,0.813 0.333,1.333 false 2.094,3.677 2.5,3.813 false 1.854,4.167 2.271,4.292 false 0.188,1.365 1.271,1.677 1.083,0.313 10 false Front Passenger Side Squib 1.656,1.594 3.021,1.802 1.365,0.208 10 false Center Airbag Sensor 0.667,0.896 0.813,1.073 0.146,0.177 10 false F 0.854,0.885 1,1.063 0.146,0.177 10 false E 1.24,0.885 1.385,1.063 0.146,0.177 10 false D 1.375,0.885 1.521,1.063 0.146,0.177 10 false C 0.51,2.5 2.844,2.854 2.333,0.354 10 false Front view of wire harness connector: (to Front Passenger Side Squib) 0.708,3.646 0.969,3.833 0.26,0.188 10 false z10 2.271,3.302 3.156,3.49 0.885,0.188 10 false Connector E 2.552,3.76 2.865,3.938 0.313,0.177 10 false SST 2.333,4.177 3.25,4.385 0.917,0.208 10 false Color: Orange

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (orange connector).

CAUTION:

Never connect the tester to the front passenger airbag (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1805, B1806, B1807, B1808 or 52 is not output.


HINT:

Codes other than DTC B1805, B1806, B1807, B1808 and 52 may be output at this time, but they are not related to this check.




OK

NG

3.CHECK CONNECTOR
3.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector E.


d.

Check that the connector is properly connected to the center airbag sensor assembly.

OK:

The connector is properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



e.

Disconnect the connector from the center airbag sensor assembly.


f.

Check that the terminal of the connector is not damaged.

OK:

The terminal is not deformed or damaged.



g.

Check that the short spring for the instrument panel wire with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.




OK

4.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT
a.
U153445E02
0.635,0.833 0.417,1.354 false 1.531,3.479 1.146,3.75 false 1.615,3.479 2,3.75 false 1.771,4.125 2.188,4.25 false 0.26,1.385 1.344,1.698 1.083,0.313 10 false Front Passenger Side Squib 1.885,1.625 3.25,1.833 1.365,0.208 10 false Center Airbag Sensor 0.74,0.917 0.885,1.094 0.146,0.177 10 false F 0.958,0.906 1.104,1.083 0.146,0.177 10 false E 1.823,0.906 1.969,1.083 0.146,0.177 10 false B 2.198,0.667 2.344,0.844 0.146,0.177 10 false A 1.333,0.896 1.479,1.073 0.146,0.177 10 false D 1.458,0.896 1.604,1.073 0.146,0.177 10 false C 0.49,2.438 2.823,2.792 2.333,0.354 10 false Front view of wire harness connector: (to Front Passenger Side Squib) 0.604,3.375 0.854,3.563 0.25,0.188 10 false z10 2.083,3.198 2.969,3.385 0.885,0.188 10 false Connector E 2.26,4.167 3.177,4.375 0.917,0.208 10 false Color: Orange 1.01,3.771 1.292,3.979 0.281,0.208 10 false P+ 1.958,3.76 2.281,3.969 0.323,0.208 10 false P-

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z10-1 (P+) - Body ground Ignition switch ON Below 1 V
z10-2 (P-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z10-1 (P+) - z10-2 (P-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z10-1 (P+) - z10-2 (P-) Always 1 MΩ or higher
z10-1 (P+) - Body ground Always 1 MΩ or higher
z10-2 (P-) - Body ground Always 1 MΩ or higher




OK

5.CHECK CENTER AIRBAG SENSOR

NG

6.CHECK CONNECTOR
5.CHECK CENTER AIRBAG SENSOR
a.
C162203E03
0.1,1.367 1.204,1.696 1.104,0.328 10 Front Passenger Side Squib 0.85,0.604 0.577,1.335 false 1.582,1.346 2.986,1.504 1.404,0.158 10 Center Airbag Sensor 1.067,0.708 1.251,0.892 0.184,0.184 10 E 0.94,0.708 1.124,0.892 0.184,0.184 10 F 1.621,0.697 1.804,0.880 0.184,0.184 10 C 1.494,0.697 1.678,0.880 0.184,0.184 10 D

Restore the released activation prevention mechanism of connector B to the original condition.


b.

Connect the connectors to the front passenger airbag and the center airbag sensor.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1805, B1806, B1807, B1808 or 52 is not output.


HINT:

Codes other than DTC B1805, B1806, B1807, B1808 and 52 may be output at this time, but they are not related to this check.




OK

NG

6.CHECK CONNECTOR
a.

Restore the released activation prevention mechanism of connector B to the original condition.


b.

Check that the connectors that link the instrument panel wire and No. 2 instrument panel wire harness are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



c.

Disconnect the connectors that link the instrument panel wire and No. 2 instrument panel wire.


d.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



e.

Check that the short spring for the No. 2 instrument panel wire connector with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.




OK

7.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE)

NG

REPLACE HARNESS AND CONNECTOR

7.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE)
a.
U153575E02
1.667,1.01 1.542,1.01 1.542,1.01 1.542,1.438 false 0.542,1.438 0.542,0.281 0.542,0.281 0.656,0.281 false 0.698,0.219 2.469,0.396 1.771,0.177 10 false Front Passenger Side Squib 0.875,0.604 2.719,0.771 1.844,0.167 10 false No. 2 Instrument Panel Wire 1.729,0.917 3.135,1.083 1.406,0.167 10 false Instrument Panel Wire 1.979,1.427 2.146,1.594 0.167,0.167 10 false A 1.646,1.656 1.813,1.823 0.167,0.167 10 false B 1.323,1.635 1.49,1.802 0.167,0.167 10 false C 1.125,1.646 1.292,1.813 0.167,0.167 10 false D 0.813,1.656 0.979,1.823 0.167,0.167 10 false E 0.615,1.656 0.781,1.823 0.167,0.167 10 false F 1.531,2.26 2.896,2.406 1.365,0.146 10 false Center Airbag Sensor 0.292,2.667 2.646,3 2.354,0.333 10 false Front view of wire harness connector: (to Instrument Panel Wire) 2.188,3.698 3.021,3.927 0.833,0.229 10 false Connector C 0.49,3.792 0.792,3.969 0.302,0.177 10 false Hz1

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Hz1-1 - Body ground Ignition switch ON Below 1 V
Hz1-2 - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Hz1-1 - Hz1-2 Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Hz1-1 - Hz1-2 Always 1 MΩ or higher
Hz1-1 - Body ground Always 1 MΩ or higher
Hz1-2 - Body ground Always 1 MΩ or higher




OK

REPLACE NO. 2 INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE